Shenzhen Rieezo Intelligent Technology T3PROMAX Smart Bracelet User Manual
- June 3, 2024
- Shenzhen Rieezo Intelligent Technology
Table of Contents
Shenzhen Rieezo Intelligent Technology T3PROMAX Smart Bracelet
Watch charging and activation
Before using the product for the first time, please charge the watch with the charger in the box. (The input voltage of the device is standard wireless charging 5.0V, please do not use other specifications of power supply for charging) Download the APP on Mobile phone
- Scan the QR code below to download the application
- You can also directly search for iband download in the application market
- You can also scan the QR code icon on the watch to download
Scan the QR code to download APP
Connect the watch
-
search device binding
Open the APP, search for devices in the ‘Device Binding’ interface, and click Bin. -
Scan code and bind
-
Watch: shortcut menu – QR code
-
Open APP – ‘Device binding’ – click QR code icon
-
Scan the QR code for binding.
In the watch shortcut menu – Settings – Device Information, the watch MAC
address will be displayed. You can determine your device through the MAC
address in the device list;
After the watch is bound successfully, every time you open the APP, the watch
will automatically connect with the mobile phone, and you can synchronize data
by pulling down the APP step counting interface.
Connect call Bluetooth
( Note: the last four digits are the MAC address of the watch)
- Open this icon. Green means open
Watch shortcut menu, click the phone icon, open the phone settings and
Bluetooth interface to search for the corresponding Bluetooth model, and click
Connect.
Change UI style
Double click the rotation button in the function list interface to switch the
UI style.
Introduction to call function
Call function This function needs to be connected to audio Bluetooth.
When dialing, you can enter the phone number as required and then dial. After
the phone is connected via Bluetooth, it will be automatically disconnected
2~5 minutes after it is not in the phone interface, and will be automatically
connected 3~5 seconds after a phone comes in.
Top contacts Favorite contacts: You need to set and add the favorite
contacts in the favorite contact bar on the APP side. The set favorite
contacts will be automatically synchronized to the device, and up to 32
contacts can be saved.
Call log Function can save the last 10 call records
Introduction to watch functions
Dial switch On the main screen, long press for 3 seconds to enter the
dial switch interface, slide left and right to switch, and click to select the
dial,
Rotation button: rotate the button on the dial page to preview all dials
shortcut menu Function overview: QR code, Call intelligent power
saving mode (When the call intelligent power saving mode is enabled, the call
automatically in sleeps situation if no call comes in for 2-5 minutes, and the
call automatically connects when it comes in. Make sure the APP be
connected.), phone, voice, brightness, settings, call mute/vibration.
music After the watch is connected to the APP, you can control the pause
and start of the mobile music player, volume adjustment and song switching
weather You can view the weather of the last three days. The data is
updated by the APP. Please connect to the APP in time to update.
Step counting interface You can view step counting related data in this
interface.
Heart rate interface If you stay on this interface for 2 seconds, your
heart rate will be measured automatically, or you can turn on the timing
measurement function in the APP.
Respiratory interface In this interface, you can set the breathing
duration, rhythm, etc.
Multisport Click to enter the sub interface to select different sports
modes for training.
Alipay Use mobile phone Alipay to scan the code for binding, and click
“agree to the agreement and bind”. After successful binding, double-click the
payment code of Alipay displayed on the main screen, or you can unbind it.
Note:
The function can only be accessed in Chinese and English.
Frequently perceived questions and answers
Why does the blood pressure value deviate from the sphygmomanometer?
The deviation between the values measured by the watch and the
sphygmomanometer is determined by a variety of factors. The measuring position
of the sphygmomanometer is in the brachial artery. The measuring position of
the watch is in the two main branches of the micro artery. Under normal
circumstances, the difference between the aortic blood pressure measurement
value and the micro arterial blood pressure measurement value will be 30 to
40; If you use a watch and a sphygmomanometer to measure at the same time,
because the blood flowing in the artery is in the centrifugal direction, the
bandage during the sphygmomanometer measurement will make the part below the
middle of your elbow under pressure, and temporarily the blood cannot flow
smoothly to the lower artery branches, increasing the tension of the blood
vessels, which will make the deviation of the upper and lower blood pressure
measurement values larger.
Why can’t I wear a watch to take a hot bath?
- The high temperature of the bath water will produce a lot of water vapor, and the water vapor is in the vapor phase. Its molecular radius is small and it is easy to seep into the gap of the watch shell. When the temperature drops, it will condense into liquid droplets again, which is easy to cause short circuit in the internal circuit of the watch, damage the watch circuit board, and then damage the watch.
- The P68 waterproof, splash proof and dust-proof function is not permanently effective, and the protection performance may decline due to daily wear.
- It does not support immersion, long time use in the rain, severe sand and dust, and high humidity environment. In addition, if the mobile phone fails due to internal water ingress, normal warranty cannot be provided.
Why can’t the watch receive the message?
Android phone settings:
- Confirm that the message push switch is enabled on the mobile client:
- The confirmation message can be displayed normally in the mobile notification bar. Watch message push is done by reading the message in the mobile notification bar; If there is no message in the mobile phone notification bar, the watch will be unable to receive the push: (You need to find the notification settings in the mobile phone settings, and turn on the notification switches of WeChat, QQ, phone, SMS, and mobile phone clients.)
- Open the auxiliary function settings of the bracelet client. (In the phone settings, find the auxiliary function settings of the auxiliary function opening bracelet client.
Apple Phone Settings:
- Confirm that the message push switch is enabled on the mobile client,
- The confirmation message can be displayed normally in the mobile notification bar.
(You need to find the notification settings in the mobile phone settings, and turn on the notification switches of WeChat, QQ, phone, SMS, and mobile phone clients.)
FCC Warnning:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuan t to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiateradio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmfulinterferenc e to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different f rom that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution:
Any changes or modifications to this device not explicitly approved by
manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>