DEURKLINK24 ELIOT On Sheild Door Lock Instructions
- June 3, 2024
- DEURKLINK24
Table of Contents
ELIOT ON SHIELD
Iinstruction Manual
ELIOT On Sheild Door Lock
Eliot on shield
Eliot on shield toilet
Eliot on shield bit lock
Eliot on shield profile cylinder
BEFORE YOU START!
Check the content.
Do you have the door handle in the rightsize? The packaging should contain:
- 2 door handles with shield
- connection pin
- 2 bolts
- Allen key
With the toilet door handle you will also find the toilet lock, a transparent adapter (to fi t the pin, if necessary) anda thin Allen key for securing the toilet lock.
MONTAGE
Gather the necessary tools.
To mount the door handle, you will need the following tools:
- tape measure for checking dimensions
- drill and an 10 mm drill bit
- flat-blade screwdriver
- pencil (or e.g. an awl) for marking the drill holes
- level (optional, but handy)
- Allen key (included)
MOUNTING
Insert the pen through the lock.
Insert the connecting pin through the lock so that it protrudes equally far on
both sides of the door.
Now slide the door handle over the pin until the door handle connects to the
door.
Secure the door handle to the pin (temporarily).
Use the supplied Allen key to temporarily ti ghten the bolt in the door handle
so that the handle remains in the correct position when marking the drill
holes.
Mark the drill holes.
Make sure that the door handle is level when you mark out the drill holes.
If the handle is mounted on the door properly and straight, use a pencil (or
an awl, for instance) to mark out the drill holes.
Drill the holes for fastening.
Unscrew the door handle with the Allen key and remove the door handlefrom the
door.
Carefully drill 10 mm diameter holes perpendicular to the door where you have
marked them.
Note! Don’t drill the holes all the way through the door yet, but only
about halfway through.
Repeat for the other side.
Now repeat steps 4, 5 and 6 for the other side of the door. You use the same
door handle for this (containing the screw holes).
Note! The drill holes should now go allthe way through the door.
Screw the door handles onto the door.
Now put both door handles back on the connecting pin and press it against the
door as firmly as possible.
Secure them in the drill holes using the included bolts. Use a hand
screwdriver (not a battery-powered screwdriver) to avoid applying too much
pressure.
Secure the door handle to the connecting pin.
Secure the door handle to the connecting pin using the Allen key.
Check that everything is securely fastened by moving the door handle up and
down several times.
If it is loose or crooked, you can easily make some adjustments using a
screwdriver.
Are you mounting a door handle with a toilet lock?
You insert the connecting pin of the toilet lock through the door. Use the
transparent adapter to make the pin fi t.Slide the knob of the toilet lock
onto thepin on the other side.
Use the included Allen key to tighten the bolt in the knob at the bottom.
We hope you enjoy your new door handle!
Free parts service
Are you missing a screw, socket bolt, washer, adapter or other parts of a door
handle or rosettethat you bought from us?
Then please send an e-mail to
info@deurklink24.nl and these parts will
then be sent free of charge.
10-year warranty
We offer a 10 year warranty on the moving parts of all door handles and
rosettes. A defect is repaired with new parts or an entirely new product.
Shipping costs are also covered by the warranty.
The lock hole does not match
When you cannot mount the door lock correctly because the lock distance of the
door latch does not match the one on your lock, exchange is no problem. Please
contact us via info@deurklink24.nl for this.
The door handle is crooked
If the door handle is not perpendicular to the shield, you can easily solve
this. You first assemble the door handle set according to the manual. Then,
gently push the door handle up until it is at a 90-degree angle to the shield.
The door handle will now stay perpendicular. If it doesn’t work, please feel
free to contact us.
Detach door handle from shield (turn handle)
With the help of locking ring pliers, it is possible to disassemble the handle
from the shield. Then you can reassemble everything in mirror image. The
visible screw holes of the shield are now on the other side. Because the
recoil spring has to be under tension, it is very difficult to reassemble the
handle. Disassembling the door handle voids the warranty.
Maintenance
Regularly wipe the door handle with a soft, possibly damp cloth. Do not use any cleaning agents. Depending on the situation, the black coating may become lighter over time. Applying a thin layer of clear wax or acid-free Vaseline largely eliminates this effect.
WE HOPE YOU ENJOY
YOUR NEW DOOR HANDLE!
DEURKLINK24
Impact 71b
6921 RZ Duiven
info@deurklink24.nl
www.deurklink24.nl
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>