AMLUXX 2 Panel Bath Screen Instruction Manual
- June 3, 2024
- AMLUXX
Table of Contents
AMLUXX 2 Panel Bath Screen Instruction Manual
Please read these instructions in full before installing
IMPORTANT
- Check that the bathtub has been installed to the manufacturer’s instructions. Please note – All product is supplied without a tray. IMPORTANT
- Opening wall adjustments 2 panel Bath screen adjustment =38.19″-39″(970-990mm)
GENERAL SAFETY INSTRUCTIONS
- Do not fix the wall profile to newly plastered, painted or papered walls as chemical reaction may cause discolouration to the surfacen finish.
- lmportant: The wall plugs included in this pack are for solid walls only. If the product is to be mounted on a partition or stud wall, specialised fixings should be purchased separately.
- Fixing tips; A piece of insulating tape or a couple of layers of masking tape applied to the wall before marking out the fixing holes will help stop the drill from wandering, particularly on tiled surfaces.
- When working near a basin or bath insert the plug into the waste,m this will help you avoid losing small parts. Also take care not to drop accessories or tools onto the bath or basin, use a towel or bathmat to protect delicate surfaces.
- CAUTION! Before drilling into any walls check that there are no hidden cables or pipes. Exercise great care when using power tools near water. The use of a residual current device (RCD) or cordless drill is recommended. Always double check the positioning and measurements before drilling holes.
Tools required (not supplied)
Electric drill| | Tape measure|
---|---|---|---
Drill(Ø3.2mm)| | Rubber hammer|
Drill(Ø6mm)| | Knife|
Cross head screw driver| | Pencil|
Spirit level| | Silicone sealant|
IDENTIFICATION OF PARTS
Fixings & fittings supplied
| Item No.: | Part | Quantity | Item No.: | Part | Quantity |
|---|---|---|---|---|---|
| 6FD01 |  | X1 | 6FD10 | X 2 | ||
| 6FD02 |  | X1 | 6FD11 | X 1 | ||
| 6FD03 |  | X 1 | 6FD12 | **** | X 1 | |
| 6FD04 |  | X 1 | 6FD13 | **R | ||
| L** | X 1 | ||||
| 6FD05 | X 4 | 6FD14 | X 4 | ||
| 6FD06 | X 4 | 6FD15 | ** ** | X 1 | ||||
| 6FD07 | X 4 | 6FD16 | X 1 | ||
| 6FD08 |  | X 1 | 6FD17 | 4mm | X 1 | |
| 6FD09 |  | X 1 |
2Panel bath sceen is ok to be installed in left and right hand.Below steps are based on left hand.Please choose the direction and following below steps.
Technical Drawing
- Put the wall profile 6FD01 against the wall,and make sure the profile to be 10mm away from the outside edge.and ensure it isvertical using a spirit level.
- Mark the holes on the wall.
- Drill the holes(Ø6mm) accordingly.
- Insert the wall plugs 6FD05(4x) in the wall.
- Fix the wall profile 6FD01 on the wall with screws 6FD07(4x) .
- Insert screen panel 6FD03 into the wall profile.
- There is 20mm(0.79″) adjustment between panel and wall profile for any out of true walls.
- From inside drill throught the vertical profile and into wall profile where shown,using a 3.2mm drill.
- Fix wall profile and frame together with screws 6FD14(4x) and washers 6FD06(4x)
- -Connect the screen panel 6FD03 and 6FD04 with hinges 6FD10( 2x).Fasten inner screws with hex key 6FD17.
- Cover the screws with cap from inside.
- -Attached the vertical anti-water sealer 6FD08 on the screen panel 6FD04
- Attched the bottom anti-water sealer 6FD09 on the screen panel 6FD04.Make sure the vertical sealer is stand on the bottom anti- water sealer.
Caution: The triangle bubble
should be mounted towards the inside of the bathtub.
- Connect the bottom anti-water strip 6FD11 with the end caps 6FD12 and 6FD13.
- Apply silicone sealant on the back of strip
- Put bottom anti-water strip on the door bottom.
- Cover the wall profile with conceal profile 6FD02 from inside.
- Put the top cover 6FD15 on the vertical profile first.
- Put the top cpver 6FD16 on the wall profile.\
- Apply silicone sealant to the outside of the enclosure. Please note: Do not apply silicone sealant to the inside of the enclosure.Also please do not take shower within 24 hours after apply the silicone.
Cleaning and Maintenance:
Please do not use abrasive or strong cleaning solutions on the shower enclosure, such as alcohol, petroleum liquids or any other chemical cleaner. Should there be any dirty stains on the shower enclosure, please clean it with a soft lint free cloth and warm soapy water. Please rinse it with clean water afterwards
We have taken great care to ensure that this product reaches you in perfect condition. However should any parts be damaged or missing please contact your poin of purchase. This does not affect your statutory rights. In addition if you require replacement parts your point of purchase will be happy to assist.
Technical and Customer Support:1-312-838-8150