Healthline 3 in 1 Bluetooth Hearing Aid User Guide
- June 3, 2024
- Healthline
Table of Contents
Healthline 3 in 1 Bluetooth Hearing Aid
Brief introduction
TWS Bluetooth Hearing Aid is compatible with both IOS and Android operating systems, the true Bluetooth connection and binaural interconnection, which can realize intelligent and free switching in listening to music, making calls, and hearing aids. This product is based on the deep cultivation of Bluetooth DSP program algorithm and enables the hearing aid to use ultra-low power consumption and high-fidelity audio, so it has the advantages of low power consumption, wide spectrum, high power, and 20 hours using time when fully charged. You will experience the bett technology, and listen to the great world wonderfully.
Product structure
-
Product name：
TWS Bluetooth hearing aid -
Designed for：
Air conduction amplifier for moderate hearing impaired people -
Mark：
Blue color for left side, red color for the right side
Install ear tips:
It is important that the tube and the dome fifit correctly into your ear. Choose the right size.
closed domes：
open domes：
OPERATION
Power on / off
Push 3 seconds on the “upper volume button”to turn on / off the hearing aid.
it flashes the green light to turn on, accompanied by (power on) voice prompt;
flashes the blue light to turn off, accompanied by (power off) voice prompt.
Pairing
Initial pairing: When power is on, press the “Volume Up button ” 6 seconds to
enter the Bluetooth pairing mode with the mobile phone ( accompanied by power
on and pairing prompts successively ), then the blue and green lights flash
alternately, accompanied by ( connected) prompt tone operation.
Volumes adjustments
One short touch to the volume up button, it will increase the volume
accompanied by two beeps voice prompt, one short touch to the volume down
button, the voice is decreased accompanied by two beeps, if only 1 beep, means
the volume reaches its maximum or minimum.
Binaural hearing aid TWS interconnection
- When power is off , long press the “Volume Up button” for 7 seconds to enter the Bluetooth pairing mode with the mobile phone (accompanied by power and paring beeps successively), then the blue and green lights flash alternately.
- Turn on the Bluetooth of the mobile phone, pair “iEarton II”, click and connect, the pairing is successful, accompanied by a (connected) voice prompt.
- Press and hold the “volume up button” of the other hearing aid for 3 seconds to turn it on, the binaural connection is successful, and accompanied by a (dong) voice prompt.
- In the Bluetooth connection mode, that is, in the hearing aid function mode.
Charging
- When the charger plug in, its red light will light up, then the hearing aid can be put in for charging; the hearing aid will light up in blue when charging and will turn off when it is fully charged. Then pick up hearing aids, it will flash green once to indicate that it is automatically turned on.
- Before charging, please turn off the hearing aids and then put it into the charger for charging, It takes about 2 hours to be fully charged . When it is in low power, hearing aids will flash blue slowly as a warning.
- If the charger power off, hearing aids will be turned on automatically.
Flight mode
Please turn off the Bluetooth function on your mobile phone when in an
airplane, or any place warned to do so, then hearing aids will enter the
airplane mode state after 10 seconds.
Hearing aid parts
WEAR
- Put the hearing aid behind the ear;
- Gently pinch the earbud with your index finger and thumb and carefully insert it into the ear canal (Note: If it is difficult to insert the earplug, you can use theother hand to gently pull the earlobe, which in turn makes the ear canal open wider so that the earbuds fit into the ear canal);
- Place the motion lock in the concha cavity.
Take out
- Turn off hearing aids;
- Lift the hearing aid above the ear;
- Grab the earplugs on the ears and gently remove them.
Common problems and solutions
lf you are experiencing issues with your hearing aid, please refer to the following methods: methods:
No sound
- Replace battery
- Check if the mic hole and receiver hole is blocked.
- Check the volume settings
Feedback
Make sure the earplugs are suitable for your Canal.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>