TECNOLOGIC UK GSM-16J Modem Kit User Manual

GSM-16J Modem Kit
User Manual

This kit enables your SMS-enabled OPLC to communicate via cellular networks.
The kit, GSM-16J Modem Kit, contains a Cinterion BGS2T GSM modem and related hardware.
The modem can communicate via GSM, GPRS + TCP/IP at 850/900/1800/1900 MHz.

Connection

Component Identification

This is the programming cable for the controller.
Jazz
Jazz does not comprise an embedded communication port. Add-on ports are available by separate order. Use the communication cable supplied with the Add-on port
2| 9-pin male adapter p/n MJ10-22-CS76|
3| LED|
4| Power supply cable|
5| End of power supply cable| Orange wire + striped orange & white wire—positive, blue wire—negative.
6| SIM Slot|
7| GSM antenna|
8| GSM antenna connector| Located on modem

SIM Slot

SIMs is inserted directly into the SIM slot in the GSM Terminal.
Insert the SIM card with the correct orientation and push it all the way in.
It will be necessary to use fingernails or a small tool to fully insert the card into the terminal Until it can be pushed no further. (Small click may be noted).
Removal is possible by pushing the SIM card back into the terminal and releasing it much that it will then be possible to completely remove the SIM card by hand.

Modem RS232 port pin-out

D-type 9 pin female connector:

Pin| Description| Direction|
---|---|---|---
1| DCD (Data Carrier Detect)| O
2| RxD (Receive Data)| O
3| TxD (Transmit Data)| I
4| DTR (Data Terminal Ready)| I
5| GND (Signal Ground)| –
6| DSR (Data Set Ready)| O
7| RTS ( Request to Send)| I
8| CTS (Clear To Send)| O
9| RING (Ring Indicator)| O

LED: Status Indication

BGS2T has two LEDs indicating the operation status through the device casing:
A green LED indicates whether the modem is correctly powered and ready to operate.
An orange LED indicates the various operation states of the terminal as per the following table.

• POWER DOWN mode
• ALARM mode
• NON-CYCLIC SLEEP mode
• CYCLIC SLEEP mode with no temporary wake-up event’
600 ms on / 600 ms off| Limited Network Service:
No SIM card inserted or no PIN entered, or network search in progress, ongoing user authentication, or network login in progress
75 ms on / 3 s off| IDLE mode: The Terminal is registered to the network (monitoring control channels and user interactions). No call in progress
75 ms on / 75 ms off / 75 ms on / 3 s off| One or more GPRS contexts activated
500 ms on / 25 ms off| Packet-switched data transfer in progress
Permanently on| Depending on the type of call:
Voice call: Connected to the remote party
CSD calk Connected to a remote party or exchange parameters while setting up or disconnecting a call

Technical Specifications

Modem

Antenna

Unitronics products sold hereunder can be used with certain products of other manufacturers at the user’s sole responsibility.
The information provided is subject to change without notice.

Modem initialization

1. Preparing the modem as described below initializes it so that it is compatible with Unitronics PLCs.

2. Connect the modem to a PC, using a cable comprising the full RS232 pinout, either supplied in the modem kit or supplied by the modem manufacturer.
   Note that using a cable that does not comprise the full RS232 pinout will cause the process to fail.

3. Prepare the PLC modem.

4. Connect the modem to a PC, using the cable supplied by the modem manufacturer.

5. Open VisiLogic/U90Ladder.

6. Open Connection>Modem Services, and select the modem type.
   If required, you can edit other parameters: Com Port, Baud Rate, Time Out, and Time-Out Reply: use the drop-down boxes. If SIM has a PIN code: click to enter the number.

7. Click the Prepare PLC-side Modem button; that dialog box opens.

8. When all parameters are set, click the Init Modem button; the PC establishes communication with the modem and initializes it to a baud rate of 9600.

9. Now you can connect the modem to the PLC using the 9 Pin connector MJ10-22-CS76 via cable 4 wires.

10. For further information please refer to VisiLogic/U90Ladder Help topic PLC Side Modems.|
    

The information in this document reflects products at the date of printing. Unitronics reserves the right, subject to all applicable laws, at any time, at its sole discretion, and without notice, to discontinue or change the features, designs, materials, and other specifications of its products, and to either permanently or temporarily withdraw any of the forgoing from the market.
All information in this document is provided “as is” without warranty of any kind, either expressed or implied, including but not limited to any implied warranties of merchantability, fitness for a particular purpose, or non- infringement. Unitronics assumes no responsibility for errors or omissions in the information presented in this document. In no event shall Unitronics be liable for any special, incidental, indirect, or consequential damages of any kind, or any damages whatsoever arising out of or in connection with the use or performance of this information.
The tradenames, trademarks, logos, and service marks presented in this document, including their design, are the property of Unitronics (1989) (R”G) Ltd. or other third parties and you are not permitted to use them without the prior written consent of Unitronics or such third party as may own them.

UG_GSM-16J.pdf 07/22
Unitronics

Documents / Resources

| TECNOLOGIC UK GSM-16J Modem Kit [pdf] User Manual
GSM-16J, Modem Kit, GSM-16J Modem Kit
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>