OTER CurBot 1S Smart Curtain Robot User Manual

Enjoy Your Spiritual Home

CurBot 1S

CurBot Instructions

* LED description

* Power button description

Track Preparation

1. Watch the track to find the matching hook
   

2. Wipe off the dust in advance to keep the track clean and smooth.
   

3. Close the curtains completely

• The bottom of the track should be smooth, not raised or spliced.	* The thickness of the rod uniform

  

CurBot Preparation

1. Press the 2 locking buttons of the circular connector to remove it. （Remove the circular connector on the other side in the same way）
   

2. Attach the track hook to the circular connector until 2 the locking buttons are out. （Attach the hook to another circular connector in the same way）

Note: The left and right ends of the rod and U rail are different

1. Attach U-rail hooks to the circular connector until 2 locking buttons are out.
   

2. Hang the hooks on the curtain rail, between the first and the second curtain clips.

3. Rotate and align the 2 circular connectors until they face each other.
   

4. Assemble the 2 circular connectors with the main body in sequence.

5. ① The drive wheel should stick to the rail, If not, the hooks may be too tight.
   Remove and reassemble.
   ② The CurBot must be perpendicular to the rail..

1. Attach I-rail hooks to the circular connector until the 2 locking buttons are out.
   Note： hooks are different on the left and right, and install them according to the picture.

2. Hang the hooks on the curtain rail, between the first and the second curtain clips.

3. Rotate and align the 2 circular connectors until they face each other..
   

4. Assemble the 2 circular connectors with the main body in sequence.

5. ① The drive wheel should stick to the rail, If not, the hooks may be too tight.
   Remove and reassemble.
   ② The CurBot must be perpendicular to the rail.

1. Attach the I-rail hooks to the o circular connector until the 2 locking buttons are out.
   Note： hooks are different on the left and right. Install them according to the picture.

2. Open the hooks
   

3. Hang on the hooks on the curtain rail, between the first and the second curtain clips. （The hook of the rod has a snap lock and needs to be pressed tightly)

4. Rotate and align the 2 circular connectors until they face each other, Lock clasp.

5. Assemble the 2 circular connectors with the main body.
   

6. ① The drive wheel should stick to the rail, If not, the hooks may be pulled too tight.
   Remove and reassemble.
   ② The CurBot must be perpendicular to the rail.

Charge

When the CurBot battery is lower than 10%, the APP pls prepare to charge：:

1. Remove device: Hold the CurBot by hand, and press 2 locking buttons of the circular connector to separate 2 circular connectors from the main body in turn.
2. Use the USB charging cable. Insert the Type-C plug into the charging port on the body, the status light will start to flash.
3. When the status light stops flash, the charge- ing is complete.

CurBot Scene

Open, Close, and Pause controls available
In addition to scene 1, add light sensing and percentage control、touch&go.)

In addition to scene 2, add voice control, scene control (linked to 30k+ Tuya equipment), etc.

Remote Control

Add Remote

Method 1:
Enter Setting->Remote->Add Remote enter to be paired, Follow the prompts to the next step.

Method 2:

1. Press the CurBot power button ” ” twice continuously enter to be paired.
2. Press any button on the remote until the status light to white.

APP Control

1. Download the OTHER app.
   （The App is regularly updated, and operation is subject to the app)|
   ---|---
   https://apps.apple.com/app/id1598554548| https://play.google.com/store/apps/details?id=com.znkit.smart.curbot
2. Click “LOG IN” and complete registration.
3. Turn on your phone’s Bluetooth.
4. Add device.
5. Select the curtain open mode.

Double Curtains

(Open to both sides)

1. Ready 2 CurBot and Hud 1S first.
2. Select “Open to both sides” to start calibration.
3. Add another CurBot to complete binding.
4. Complete calibration.

Light Sensing

（Set curtains to open/close automatically under different light levels）

1. Open the OTHER app, enter the CurBot settings, and turn on the switch for light sensing.
2. Turn off the switch if it isn’t needed.
   Note: default is off.

Touch & Go
（Pull the curtain by hand, and CurBot will automatically move the curtain to open/close)
Open the OTHER app, enter the CurBot settings, and turn on the switch for touch&go.
Note: default is off

Hub Control

(Connect your CurBot and add functions such as timing, temperature sense, and scene settings)

1. Hub uses a Micro-USB cable to power on.
2. Add “Gateway” in another app.
3. Add sub-devices, and select CurBot.

Voice Control

(Control your curtains with Alexa and Google Assistant）

1. Make sure Alexa or Google Assistant is connected to the Internet.
2. Use the OTHER app to complete the connection between the CurBot and Alexa or Google Assistant.

About Update
The version of the device is continuously updated, which can be viewed and updated from the Setting. The version of the device is continuously updated, which can be viewed
and updated from Setting.

Specifition

NOTICE:

1. Make sure circular connectors are buckled, otherwise, the CurBot could fall off.
2. Do not place the CurBot near heat sources.
3. 3. Do not spill liquids such as water on the CurBot.
4. If the CurBot fails, contact us at Support@oter-group.com Do not disassemble and maintain it by yourself.

The manual and APP will be continuously updated, please check the APP for the latest version.

FCC Warning statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC RF exposure statement:
The equipment complies with the FCC Radiation exposure limit set forth for an uncontrolled environment. The equipment should be installed and operated with a minimum distance of 20cm between the product and your body.

FCC ID：2A46D-CURBOT03

www.oter-group.com

References

• Group Publishing
• Oter-Group | All-sensory sleep space

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>