RYOBI RYi1030A 1000W Auto Power Inverter Instruction Manual

RYOBI RYi1030A 1000W Auto Power Inverter

IMPORTANT SAFETY INSTRUCTIONS

WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
SAVE THESE INSTRUCTIONS – This manual contains important safety and operating instructions for inverter model RYi1030A.
NOTICE: This product’s AC receptacle has a non-sinusoidal output and is not recommended for use with certain types of sensitive electronics.
Please refer to your product’s operator’s manual.

• This product is for indoor use only.
• Do not expose inverter to rain or snow, or use when wet.
• Do not disassemble the inverter.
• To reduce the risk of injury, close supervision is necessary when an appliance is used near children.
• Store inverters indoors and away from children.
• As with all electrical devices, use caution when plugging and unplugging this unit into an outlet or plugging/unplugging other devices into this unit. Do not force this unit into an outlet. Do not force plugs into this unit.
• To reduce the risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting inverter.
• Do not use inverter if it has been dropped or received a sharp blow. A damaged inverter will increase the risk of fire.
• If this unit is used in a manner not specified by the manufacturer, the protection provided by this equipment may be impaired.
• Do not overload the tool. It must be used for powering devices less than the product rating.
• Operate this product using only the AC power type listed in the product specifications.
• Two- or three-prong plugs may be used with this product. Do not force a polarized plug (one prong larger than the other) into this product. Flip plug over and retry.
• Never block air vents. Blocked vents may cause overheating. Inverter will automatically shut off when overheated.
• Keep inverter cool. Do not place near vehicle heat vents or in direct sunlight.
• Do not store appliance in locations where the temperature is less than 14°F or more than 104˝°F. Do not store outside or in vehicles.
• Do not use appliance in locations where the temperature is less than 14°F or more than 104°F.
• Use this product only with batteries and chargers listed in tool/appliance/battery pack/charger correlation supplement 987000‑432.
• Use only with power cord provided.
• Disconnect inverter from power supply when not in use.
• Do not use the inverter around flammable fumes and gasses, such as in the bilge of a boat or near propane tanks.
• Do not use in an enclosed area with automotive lead acid batteries.
• Do not put foreign objects into the inverter.
• Refer to the operator’s manual for the vehicle or contact the vehicle manufacturer for the proper 12V power receptacle.

WARNING: To reduce the risk of fire, do not connect to an AC load center (circuit breaker panel) having multiwire branch circuits connected.

• Do not power life support devices or other necessary medical equipment with this tool.
• This unit should never be hard wired into a circuit.
• This unit should never be wired into a AC distribution circuit.
• Do not attempt to set up, make adjustments or power devices while operating a vehicle.
• Save these instructions. Refer to them frequently and use them to instruct others who may use this product. If you loan someone this product, loan them these instructions also.

TTI OUTDOOR POWER EQUIPMENT, INC.
P.O. Box 1288, Anderson, SC 29622, USA
1-800-525-2579 www.ryobitools.com

WARNING: Risk of Fire.
Do not replace any vehicle fuse with a rating higher than recommended by the vehicle manufacturer. This product is rated to draw 12 amperes from 13.8V vehicle outlets. Ensure that the electrical system in your vehicle can supply this product without causing the vehicle fusing to open. This can be determined by mak-ing sure the fuse in the vehicle which protects the outlet is rated higher than 12 amperes. Information on the vehicle fuse ratings are typically found in the vehicle operator’s manual. If a vehicle fuse opens repeatedly, do not keep replacing it. The cause of the overload must be found. Fuses should not be patched up with tin foil or wire as this may cause serious damage elsewhere in the electrical circuit or cause fire.

PRODUCT SPECIFICATIONS

Total Power Output…………………………….. Continuous 1,000 Watts Max
12V DC Adaptor Connection…………………………………………120 Watts
18V Battery Connection……………………………………………….300 Watts
Direct to Battery Connection (Car Battery Clamps)………. 1000 Watts
DC Input………………………………………………………………………12 Volt DC
AC Output…………………………….. 120 Volts, 120W max. (12V DC plug);
300W max. (18V battery);
850W max. (12V battery terminal)
USB-A Output……………………………………………….5V 2.4A Shared Max.
USB-C PD Output…………………………………… 5V(3A), 9V(2A), 12V(1.5A),
15V(1.5A), 20V(1A) DC
Output Wave Form…………………………………………..Modified Sine Wave

PACKING LIST

• RYi1030A Inverter
• Car Battery Clamps
• 12V DC Adaptor Cable
• Mounting Brackets
• Operator’s Manual

OPERATION

APPLICATIONS
You may use this product for the following purposes:

• Operating and charging USB-powered devices
• Supplying electrical power for operating compatible electrical devices such as, but not limited to, lighting, appliances, tools, motor load, small load switch mode power supply, and fans

The power inverter converts low voltage DC electricity to 120V AC household power allowing user to charge and power a variety of devices.

WARNING: Risk of electric shock.
When using a grounded appliance this tool will not provide an electrical path to earth ground. Do not power devices with damaged or frayed power cords.

NOTICE :
Do not power this device with an outlet designated for lighting cigarettes. If the 12V adaptor does not fit firmly into the auxiliary power port, the receptacle is not suitable for use with the inverter. A poor connection at the base of the 12V adaptor could lead to electrical problems in the vehicle outside of the protections offered by the vehicle or inverter’s fuse.

INSTALLING THE MOUNTING BRACKETS

See Figure 1
The mounting brackets can be installed to provide a stable base for the inverter. The unit can be used horizontally or mounted vertically.

• Insert tabs into slot.
• Rotate 90 degrees.

A – Mounting bracket
B – Tabs
C – Slot

CONNECTING TO AN 18V BATTERY

See Figure 2

• To install: Place the inverter adaptor onto the battery as shown. Make sure the battery pack is secured on the inverter adaptor before beginning operation.
• With power inverter turned off, insert connector cord plug into receptacle in rear of inverter.
• To remove: lift off the battery pack.

A – Power inverter
B – 18V battery
C – Connector cord plug

CONNECTING TO A 12V AUTO ACCESSORY OUTLET

See Figure 3
Using your vehicle’s 12V DC receptacle, the inverter will provide power through a 120V AC outlet and/or two USB ports. NEVER use inverter with any 12V DC power source that uses a positive ground.

NOTE: Some vehicles require the ignition to be turned on before power is supplied to an accessory outlet.

• With power inverter turned off, insert connector cord plug into receptacle in rear of inverter.
•  Plug the 12V DC plug into the 12V DC power port.

A – Power inverter
B – 12V DC plug
C – 12V DC power port
D – 12V DC input cable
E – 12V DC input receptacle

USING CAR BATTERY CLAMPS TO CONNECT TO 12V BATTERY

See Figure 4
A set of car battery clamps is included with the inverter, one for the black lead, and another for the red lead. When you want the inverter to remain connected to the battery, but want to keep your hands free for other operations, the car battery clamps will hold the leads in place. To use the clamps:

• Make sure the inverter is turned off.
• Connect the red cable to the positive (+) terminal first, then connect the black cable to the negative (-) terminal. Make sure all connections are tight.
• Connect the cables to the battery using the car battery clamps.
  NOTE: Do not allow the inverter to hang by its leads when the clamps are connected to the battery.

CAUTION : To avoid damaging the inverter or blowing the fuses, always remove the test leads from the battery.

A – Black cable (–)
B – Red cable (+)
C – Car battery clamps
D – Negative (–) terminal
E – Positive (+) terminal

USING THE POWER INVERTER

See Figures 4 – 6

• Press and hold the power button for 1.5 seconds to turn the inverter ON. The LED will light up green when ready to use.

• Plug devices you want to power or charge into the inverter’s USB ports and/or 120 volt receptacle.

  • If the power button LED blinks red then turns off, the inverter may be overloaded. Disconnect your device, make sure your battery pack is sufficiently charged to power your device, then press the button to turn the inverter back on. Reconnect your device and try again. If the fault condition immediately reoccurs, the item being powered exceeds the capacity of the inverter.
  • If the power button LED turns red but does not shut down the inverter, the inverter is overheated. Allow the unit to cool until the LED turns green, then try again.
  • If the power button LED flashes yellow, the battery pack needs to be recharged.

• Tap the power button one time to toggle between output power (watts) and input power (volts) on the digital display.

• To use the worklight, press the light button. Press the light button again to turn the worklight off.
  NOTE: The inverter must be on for the worklight to function.

• When finished, disconnect your device and press the power button indicator again for three seconds to turn off the inverter.

NOTE: When needed, an internal cooling fan will run to regulate the unit’s operating temperature. If running, always wait for the fan to stop before you disconnect the battery pack from the inverter.

A – LED power button/overload indicator
B – 120 V receptacle
C – USB-A ports
D – 2.4A USB-C PD port
E – LCD display
F – LED light

A – Battery level
B – Battery type
C – AC power
D – Error
E – Input voltage “V” and output wattage “W”

MAINTENANCE

REPLACING THE FUSE
See Figure 7
Always replace the fuse with a 5D 12 Amp fast blow glass fuse. Never replace the fuse with a higher-rated fuse.

A – Fuse cover
B – Fuse cap
C – 12 amp fuse
D – 12 volt DC plug

• Make sure LED power button/overload indicator is OFF.
• Disconnect any USB or AC devices that are plugged into the inverter.
• Unscrew fuse cover and remove from 12 V plug.
• Remove fuse cap.
• Remove the blown fuse. Replace with the new fuse.
• Reinstall the fuse cap and fuse cover. Tighten securely.

REPLACEMENT PARTS

The following replacement parts may be ordered by calling our customer service department at 1-800-525-2579:
12A Glass Fuse…………………………………………………………… 870291007
Car Battery Clamps……………………………………………………… 290426056
12V DC Adaptor Cable…………………………………………………. 290426041
Mounting Bracket………………………………………………………… 638700062

WARRANTY

This product has a Three-year Limited Warranty for personal, family, or household use (90 days for business or commercial use). For warranty details, visit www.ryobitools.com or call (toll free) 1-800-525-2579.

FCC COMPLIANCE

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Model/item number on product may have additional letters at the end. These letters designate manufacturing information and should be provided when calling for service.

References

• REIMAGINE WITH RYOBI - RYOBI Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>