TECMIX TMX PRO 1400 Electronic Double Stirrer Instruction Manual
- June 3, 2024
- TECMIX
Table of Contents
TECMIX TMX PRO 1400 Electronic Double Stirrer
TMX PRO 1400 DOUBLE
Technical Data
Electronic Power Mixer
- TECHNICAL DATA TMX PRO 1400 DOUBLE
- Power Input 1400 W
- Voltage 230V/50Hz – 110V/60Hz
- Nm 45
- Number of Gears 2
- No-Load-Speed (min-1) 0-480 / 0-680
- Ampère (110V) 15,00
- Ampère (230V) 7,00
- Protection / Class of Protection Double Insulation / II
- Certification CE
- Thread of fixing the tool 2 x HEX 13
- Mixing Paddle (Ø max.) 120 mm
- Electronic Speed Control
- Net weight 6.9 kg
Control Elements
- 20 Switch / Arresting pin
- 21 Gear Switch
- 16+17 Handle incl. electronic speed control
- 03 Motor Housing
- 64 Mixing-Paddles*
- 65 Spindle holding fixture
Accessories supplied with the instrument may differ from the parts depicted or described in this instruction.
Safety Precautions
Safe operation of this machine is only possible when the operating instructions and the safety precautions are read completely and the instructions contained therein are strictly observed.
- The machine is not qualified for operation in environments where danger of explosion exits.
- The machine must not be damp and must not be operated in a wet environment.
- Always inspect cable and plug before using machine. Only have damage repaired by a qualified professional.
- Connect machines that are used in the outside-area via a residual current circuit breaker. Use only extension cables that are intended for outdoor use and are protected against splash water.
- Put the plug into the mains socket only when the machine is switched off.
- Always lay the cable away from the machine towards the rear.
- Take care of long hair and fashion accessories; work in properly buttoned-up clothes, without freely flowing parts.
- When working with the machine, always hold it firmly with both hands and provide for a secure stance. Secure the vessel with the mixed substance against moving on the floor.
- To be on the safe side, always use the handle (16 + 17). Consider possible reaction torque.
- Do not carry the machine by the power cord.
- Before any work on the machine itself, pull the mains plug. If the cord is damaged, it should be replaced by the manufacturer or an authorized service department to avoid dangers.
Starting Operation and Use
Check if the data on the nameplate is corresponding with the actual mains voltage. Instrument scheduled for 230V can be plugged to 220V/240V mains. Improper use may damage the Instrument.
Observe therefore these instructions:
- Use just mixing paddles up to the specified diameter.
- Load the instrument in such a way that the speed would not drop considerably or that it would stop.
Fixing mixing-paddles:
Push down the chuck by hand; connect the paddles (64) HEX 13 into the spline
shaft directly and than loose your hand.
Switching On and Off :
By pressing the switch button (20) the stop and simultaneous pressing the
arresting pin the machine is brought into operation and it stops when this is
relieved.
Maintenance
- This power tool normally requires no maintenance; from time the ventilation holes on the motor housing (3) should be cleaned out.
- After approx. 50 hours of operation, check the motor brushes and replace if necessary. Clean the motor housing.
- After approx. 200 hours of operation, renew the grease filling in the gearbox.
To verify that the protective insulation remains intact, the machine must be subjected to a technical safety test afterwards. For this reason, this work must be performed exclusively by a professional workshop. Environment Protection Do not open worn out machines and return to the collection facilities provided for recycling. Storage The unit should be stored in a dry place where it is protected against freezing.
Guarantee
We guarantee appliances in accordance with statutory/country-specific regulations. Proof of purchase by invoice or delivery note. The guarantee is only valid with a stamp of your dealer on the invoice, which shows the date of purchase and the serial number of the item.
Noise / Vibration Information
Measured values determined according to EN 60 745.
Wear ear protection!
- Electronic Power Mixer TMX PRO 1400 DOUBLE
- A-weighed noise level 88.3 dB(A)
- Sound pressure level 99.3 dB(A)
- Hand-Arm-Vibration 0.496 m/s²
CE / UKCA Declaration of Conformity
We declare under our sole responsibility that this product is in conformity with the following standards or standardization documents:
- 2006/42/EC:
- EN 62841-1:2015+AC:15
- EN 62841-2-10:2017 EK9-BE-88(V2):2020
- 2014/30/EU:
- EN 55014-1:2017
- EN 55014-2:2015
- EN IEC 61000-3-2:2019
- EN 61000-3-3:2013+A1:2019
Fabian Berg Authorized Person for technical documentation, General Manager Cologne, July 2021 UK Authorised Representative: Authorised Rep Compliance Arc House Thurnham Lancaster LA2 0DT BERG TECTOOL GmbH Hermann-Heinrich-Gossen- Str. 3 50858 Köln Germany Subject to modifications
SPECIFICATION
CE DECLARATION OF CONFORMITY
BERG TECTOOL GMBH, Cologne, declares under its full responsibility that the
power tool is in conformity with directives of the European Parliament
Directive 98/37/EC 2006/42/EC, Directive and Directive 2014/30/EU and complies
with the requirements of the following standards:
- EN 62841-1:2015+AC:15
- EN 62841-2-10:2017, EK9-BE-88(V2):2020,
- EN 55014-1:2017, EN 55014-2:2015, EN IEC 61000-3-
- 2:2019, EN 61000-3-3:2013+A1:2019
BERG TECTOOL GmbH
Hermann-Heinrich-Gossen-Str. 3
50858 Köln
Germany
Fon : +49 (0) 221 – 964966 – 0
Fax : +49 (0) 221 – 964966 – 22
www.bergtectool.com
bt@bergtectool.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>