JASTIND JTCVT-01B Digital LCD Circuit Tester User Manual

JASTIND JTCVT-01B Digital LCD Circuit Tester

INTRODUCTION

The JASTIND JTCVT-01B Digital LCD Circuit Tester is an important tool for electricians, workers, and do-it-yourselfers who want to test electrical systems accurately and reliably. This gadget, which costs $18.99, has advanced features built into a sturdy body, making it a great deal. The tester can measure voltages starting as low as 3 volts and has a digital LCD display for clear readings. This makes it useful for a wide range of tasks. The JTCVT-01B was made by Tianchang Zhaohong Instruments, a recognized expert in precise tools, to meet the growing need for reliable and easy-to-use circuit testing tools. At only 140 grams, its form makes it easy to carry and handle, making it perfect for use at home or in the office.

SPECIFICATIONS

WHAT’S IN THE BOX

• Circuit Tester
• Manual

PRODUCT OVERVIEW

FEATURES

• Test Range: It can check DC voltages between 3V and 48V, which makes it useful for many electrical and automotive uses.

• High Resolution: It has a resolution ratio of 0.1V, which means it can read voltages very accurately.

• Voltage Accuracy: Gives correct results with a range of ±0.2V, making sure that diagnostics are reliable.

• The LCD digital display has a backlit LCD screen that makes it easy to read, even in dim light.

• Sharp Stainless Steel Probe: It comes with a sharp stainless steel probe that makes it easy to cut through insulation and get to places that are hard to get to.

• 140-inch Extended Spring Wire: The 140-inch PU spring wire lets you move and reach freely while checking circuits.

• Heavy-Duty Construction: This circuit tester is made from high-quality acetate fiber, which makes it tough and impossible to break.

• Large Alligator Clip: The large clip design makes it easy to use with one hand and makes ties to the ground safe.

• Backlight Display: The LCD screen has a white backlight that makes it easier to see in poorly lit rooms.

• Battery-Powered: Depends on batteries to work, so it can be taken with you without an extra power source.

• Low Voltage Testing: This type of testing is meant to check low-voltage circuits, like those in car batteries and electronic parts.

• Uses Many Things: It’s great for checking electrical circuits in cars, like headlights, taillights, turn signal circuits, broken plugs, and fuses.

• Simple to Use: The alligator clip should be connected to the ground, and the probe should be connected to the circuit being checked.

• Tool That Saves Money: At $18.99, it’s a great deal for car engineers and people who like to do their projects.

SETUP GUIDE

• Unpack the Tester: Take the JASTIND JTCVT-01B out of its box carefully.
• Check the Installation of the Batteries: Make sure the batteries are installed properly by following the polarity markings on the battery compartment.
• Get to Know the Features: Look over the tester’s features and buttons to make sure you know how to use it correctly.
• Pick a Testing Area: To do your first voltage checks, pick a safe, well-lit area.
• Connect the Alligator Clip: Connect the big alligator clip to the test circuit’s ground.
• Connect the Probe: Touch the wire, fuse, or socket being checked with the sharp stainless steel probe.
• Power on the Tester: If the tester has a power switch, flip it on. If not, it may turn on itself when you connect it.
• Watch the LCD Screen: While the probe is in touch with the circuit, keep an eye on the LCD screen for voltage readings.
• Read Backlight Indicators: If trying in a dark room, make sure the backlight display works so that the screen is easy to see.
• Use an Extended Spring Wire: For flexibility and ease of movement during tests, use the 140-inch PU spring wire.
• Do Different Tests: To get used to how the tester works, try different circuits, such as headlights, batteries, and fuses.
• Power Off After Use: If the tester can be turned off, do so. If not, let it go into auto-power-off mode after a few minutes of silence.
• How to Store It: When not in use, put the tester somewhere dry and safe.
• Follow Safety Precautions: Always try in a safe place, away from AC circuits, and make sure the connections are correct.

CARE & MAINTENANCE

• Clean the tester regularly by wiping the outside with a soft, dry cloth to get rid of dust and dirt.
• Check for Damage: The probe and alligator clip should be checked regularly for signs of wear or damage that could affect how well they work.
• Keep in a Dry Place: To keep the tester from getting damaged by water, keep it in a cool, dry place.
• Avoid Extreme Temperatures: Do not leave the tester out in direct sunlight or very hot or cold temperatures for long amounts of time.
• Quickly Change the Batteries: If the LCD screen goes dark or the tester won’t turn on, you need to change the batteries right away.
• Limit Exposure to Moisture: To keep the tester safe, make sure it is used in dry circumstances.
• Be Careful: To keep the tester working properly, don’t drop it or hit it with something.
• Check the Connections: Make sure the alligator clip and probe connections are always safe and working by checking them often.
• Test on Known Circuits: Test on known good circuits on a regular basis to make sure the system works.
• secure Case: If you have one, put the tester in a secure case to keep it from getting broken.
• Watch the Battery Life: Keep an eye on the battery life to make sure it works well while you’re using it.
• Calibrate if Needed: If the readings don’t seem to match up, look in the manual for directions on how to calibrate.
• Keep Out of Reach of Children: To avoid mistakes, keep the tester out of reach of children.

TROUBLESHOOTING

health.
Cannot measure below 3 volts| Verify operational range; the device starts at 3 volts.
Readings fluctuate| Ensure steady contact and minimal movement while testing.
Device overheats| Stop use immediately, allow to cool, and check the battery.
Screen is dim| Adjust the contrast if available, or replace batteries.
Tester drops readings| Check for loose connections or damaged leads.
Unresponsive buttons| Clean the button area, and ensure nothing is obstructing them.
Error message on display| Consult the user manual for specific error information.
The tester gives a continuous beep| Check for constant voltage source or tester fault.
The device does not turn on| Ensure batteries are fresh and properly installed.
Intermittent display flickering| Secure all internal connections; may require service.
The tester does not respond to changes| Reset the device or replace if the fault persists.

PROS & CONS

PROS

• Affordable price point at $18.99.
• Digital LCD for clear and accurate readings.
• Lightweight and portable, ideal for on-the-go use.
• Can measure low voltages, starting from 3 volts.
• Battery-powered for convenient field use without needing an external power source.

CONS

• Limited to battery power, and may require frequent replacements.
• No capabilities for AC voltage testing.
• May not be suitable for high-voltage industrial applications.
• Requires familiarity with digital devices for optimal use.
• Not waterproof or dustproof, limiting use in harsh environments.

WARRANTY

The JASTIND JTCVT-01B Digital LCD Circuit Tester comes with a one-year manufacturer warranty. This warranty covers defects in materials and workmanship and offers customers peace of mind, ensuring that any issues can be addressed directly through Tianchang Zhaohong Instruments’ customer service.

FREQUENTLY ASKED QUESTIONS

What is the brand and model of this digital circuit tester?

The brand is JASTIND, and the model is JTCVT-01B.

What is the price of the JASTIND JTCVT-01B Digital LCD Circuit Tester?

The JASTIND JTCVT-01B is priced at $18.99.

What type of power source does the JASTIND JTCVT-01B use?

The JASTIND JTCVT-01B is battery powered.

What is the item weight of the JASTIND JTCVT-01B Digital LCD Circuit Tester?

The item weight of the JASTIND JTCVT-01B is 140 grams.

What measurement type does the JASTIND JTCVT-01B use?

The JASTIND JTCVT-01B functions as a voltmeter.

What is the minimum operating voltage for the JASTIND JTCVT-01B?

The minimum operating voltage for the JASTIND JTCVT-01B is 3 volts.

Who is the manufacturer of the JASTIND JTCVT-01B Digital LCD Circuit Tester?

The manufacturer of the JASTIND JTCVT-01B is Tianchang Zhaohong Instruments.

Is the JASTIND JTCVT-01B suitable for testing low voltages?

JASTIND JTCVT-01B is suitable for testing low voltages starting from 3 volts.

What types of circuits can the JASTIND JTCVT-01B test?

The JASTIND JTCVT-01B can test AC and DC circuits, making it useful for a variety of electrical applications.

How does the JASTIND JTCVT-01B indicate voltage detection?

The JASTIND JTCVT-01B provides visual indicators on the LCD display to show voltage levels detected during testing.

Why won't the JASTIND JTCVT-01B Digital LCD Circuit Tester turn on?

Ensure that the batteries are installed correctly and have sufficient charge. If the device does not power on, try replacing the batteries with new ones.

What should I do if the JASTIND JTCVT-01B Digital LCD Circuit Tester is giving inconsistent readings?

Inconsistent readings may occur if the probe is not making good contact with the circuit. Ensure that the test probes are firmly connected to the circuit and that you are using the tester as directed.

How can I troubleshoot if the JASTIND JTCVT-01B Digital LCD Circuit Tester is not detecting voltage?

First, check that the device is set to the correct mode for voltage detection. Ensure the battery is functional and test the device on a known live circuit to confirm its operational status.

What does it mean if the display on the JASTIND JTCVT-01B Digital LCD Circuit Tester is blank?

A blank display may indicate low battery power or an internal issue. Replace the batteries and check the connections. If the display remains blank, the device may need servicing.

Why is the JASTIND JTCVT-01B Digital LCD Circuit Tester giving false positives when testing for voltage?

False positives can happen if the tester is too close to a strong electromagnetic field or if there is interference from nearby electrical devices. Ensure you are testing in a safe environment away from high-voltage sources.

VIDEO – PRODUCT OVERVIEW

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>