K-GEAR GS6 Passive Subwoofer Installation Guide

September 27, 2024
K GEAR

GS6 Passive Subwoofer

Specifications:

  • Type: Passive / Active Subwoofer
  • Transducers: 6″ Woofer
  • Frequency Response: Not specified
  • Max SPL: Not specified
  • Power Handling: Not specified
  • Nominal Impedance: Not specified
  • Coverage: Not specified

Product Usage Instructions:

Installation:

  1. Place the GS6 subwoofer in a suitable location in your indoor
    space.

  2. If using the passive GS6, ensure it is connected to a
    compatible amplifier or speaker system.

  3. If using the active GS6A, connect it directly to the speaker
    from the GF family without an external amplifier.

Connection:

Connect the GS6 or GS6A subwoofer to the same line as the
satellites with no additional EQ or DSP required, thanks to the
built-in low-pass filter.

Operation:

Power on the subwoofer and adjust the volume level as needed to
complement your existing speaker setup.

FAQ:

Q: What amplifiers are suggested for use with the GS6

subwoofer?

A: The GA201 amplifier is recommended for
optimal performance with up to 4 pieces per channel at 8 ohms.

Q: Can the GS6 be used in retail and hospitality settings?

A: Yes, the GS6 is suitable for use in retail
shops, restaurants, hotels, bars, and other indoor spaces.

GS6 6″ Passive / Active 4 Subwoofer

The GS6 is a 6″ passive subwoofer designed for indoor applications in permanent installations for retail shops, restaurants, hotels, bars and residential spaces.
Designed to match our GF22 and GF82 loudspeakers as a low frequency extension device, the GS6 features a symmetrical load circuit that allows to be connected directly to most standard loudspeakers such as the GF series.
The GS6A active subwoofer is equipped with an on-board amplifier to easily drive any speaker from the GF family without the need of an external amplifier module.
GS6 and GSA, thanks to a built-in low-pass filter, do not require any additional EQ or DSP and can be connected to the same line as the satellites with no hassle!

General
Type Transducers Frequency Response Max SPL 1 Power Handling Nominal Impedance Coverage

Passive subwoofer 6″ ferrite woofer 50 Hz ­ 140 kHz (-10 dB) 108 dB (peak) 120 W 4 OMNI

Frequent Applications

1 Maximum SPL is calculated using a signal with crest factor 4 (12dB) measured at 1 m.

Retail

Cafes, Bistros & Restaurants

Hotels & Resorts

Fitness & Wellness

Suggested amplifiers

GA201

up to 4 pcs/ch @ 8

Handling & Finishes
Dimensions (WxHxD) Weight Material Color

170 x 310 x 310 mm (6,7 x 12,2 x 12,2 in) 3,2 kg (7 lb)
Birch Plywood
Black

·20240429·

+ ­
+ ­

KGEAR GA201

­ +

­

KGEAR GF82 (LEFT)

KGEAR GS6 (SUB)

­

KGEAR GF82 (RIGHT)

310 mm [12.2 in]

310 mm [12.2 in]

Mechanical Drawings GS6
170 mm [6.7 in] 170 mm [6.7 in]

310 mm [12.2 in] 310 mm [12.2 in]

11 22
Signal input: + 1 : signal ­ 1 : signal
Signal input: + 2 : speaker relaunch ­ 2 : speaker relaunch

Power IN DC + DC Output + 1 spk out – 1 spk out

Control: Mute contact ON / OFF switch Balanced Input: GND + 1 : signal ­ 1 : signal

GS6A – wiring

POWER OUTPUTS DC – DC +

24V DC POWER SUPPLY

LINE IN

MUTE CONTACT normally open

GND

MUTE

INPUTS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals