ULANDPOWER UN1A48 Electric Vehicle Charging Station User Manual

ULANDPOWER UN1A48 Electric Vehicle Charging Station

Specifications

• Output Amperage: 16A, 32A, 40A, 48A
• Circuit Breaker Options : 20A, 40A, 50A, 60A
• Mounting Height: Between 2 feet (600 mm) and 4 feet (1200 mm) from ground
• Installation Requirements : Must be done by a qualified technician
• Maintenance: Keep the charger in a clean area with low humidity

Product Usage Instructions

Safety Instructions

Overall Warnings & Cautions:

• Avoid fire, injury, or death by carefully reading and following installation, operation, and maintenance instructions.
• Do not insert fingers into the electric vehicle connector.
• Do not use if the power cord or EV cable is damaged.
• Do not use if the enclosure or EV connector is damaged.
• Do not attempt to open the enclosure.
• Supervise devices when used around children.
• Ensure proper grounding.
• Avoid using with extension cords.

Installation Requirements:

• Disconnect electrical power before installing the charging station.
• Review user manual and local building/electrical codes before installation.
• Installation must be done by a qualified technician.
• Use appropriate protection when connecting to main power distribution cable.
• Install the correct type of breaker in the upstream AC distribution box.
• Mount the device at a height between 2 feet and 4 feet from the ground.

Daily Maintenance:

• Keep the charger in a clean area with low humidity.
•  Avoid installing in coastal environments with high humidity orhigh dust.
• Perform regular maintenance checks before each use.

Product Introduction
Avoid placing the charger near hot objects, high-temperature locations, flammable gases, or corrosive materials.

Basic Interface
The product features an enclosure, LCD screen, RFID & Touch Switch, and LED status indicators.

IMPORTANT SAFETY INS INSTRUCTIONS

Overall Warnings & Cautions
WARNING : To avoid fire, injury or death, carefully read and follow the instructions during installation, operation and maintenance

• DO NOT put fingers into the electric vehicle connector.
• DO NOT use this product if the flexible power cord or EV cable is frayed, insulation-broken, or any other signs of damage.
• DO NOT use this product if the enclosure or the EV connector is broken, cracked, open, or shows any other indication of damage.
• DO NOT remove cover or attempt to open the enclosure because of risk of electric shock.

WARNING:

• This device should be supervised when used around children.
• This device must be grounded.
• To avoid a risk of fire or electric shock, do not use this device with an extension cord.
• The suitability of the use of flexible cord in accordance with CE code, part I, rule 4-012, is to be determined by the local inspection authority.
• To reduce the risk of fire, connect only to a circuit provided branch circuit over-current protection in accordance with the CSA C22.1–15 Canadian Electrical Code, Part 1 (Canada) or NOM-001-SEDE Electrical installations (utility) (Mexico) or  ANSI / NFPA 70 National Electrical Code (USA).

Circuit Breaker Options table

Output Amperage (A)| 16A| 32A| 40A| 48A
Circuit Breaker Options

(A)

| 20A| 40A| 50A| 60A

Installation Requirements
WARNING :

• Disconnect electrical power prior to installing the charging station.
• Be sure to preview the user manual and ensure local building and electrical codes are reviewed before installing the AC charger.
• The AC charger should be installed by a qualified technician according to the user manual and local safety regulations.

CAUTION:

• Use appropriate protection when connecting to the main power distribution cable.
• Type B, C or D breaker with the rating current for table should be installed in the upstream AC distribution box.
• Disconnect switch for each ungrounded conductor of AC input shall be provided by others in accordance with the National Electric Code, ANSI/NFPA70.
• The device shall be mounted at height between 2 feet (600 mm) and 4 feet (1200 mm) from ground.
• Please keep the charger in a clean area with low humidity. Not recommended to be installed in coastal environments with high humidity or high dust.

Daily Maintenance

• CAUTION: Avoid moisture or water in the charger. If there is water or moisture ingress in the charger, it is necessary to immediately power off to avoid immediate danger, and notify the professionals to carry out maintenance before next use.
• CAUTION : Please use the charger properly. Do not hit or press hard on the enclosure. If it is damaged, please contact a professional technician.
• CAUTION : Avoid placing the charger near hot objects and at high temperature locations and away from dangerous substances such as flammable gases and corrosive materials.

PRODUCT INTRODUCTIONS

CAUTION : Avoid placing the charger near hot objects and at high temperature locations and away from dangerous substances such as flammable gases and corrosive materials.

Basic Interface

Basic Dimension

Specifications

Design Standards

• IEC61851:Electric vehicle conductive charging system
• UL 2594: Electric Vehicle Supply Equipment
• UL 2231-1: ULPrersonnel Protection Systems forElectric Vehicle (EV) Supply Circuits:

General Requirements

• UL 2231: Personnel Protection Systems for Electric Vehicle (EV) Supply Circuits:

Particular Requirements for Protection

• Devices for Use in Charging Systems
• UL 2251: Plugs, Receptacles and Couplers for Electric Vehicles
• UL 62: Flexible Cords and Cables
• UL 991: Tests for Safety-Related Controls
• Employing Solid-State Devices
• UL 1998: Software in Programmable

Components

• NFPA 70 Article 625: National Electrical
• Code, Electric Vehicle Charging System
• UL 840 (Clearance and Creepage)

VERIFY CONTENTS

Check the box to ensure you have this installation guide and these parts:

and output charging cable

2| User Manual| 1| PDF version available online
3| Wall-Mounted Bracket| 1| For mounting the charging station to

the wall/structure

4| M5 Anti-Theft Round

Head Screws

| 2| For securing the charging station to

the Mounting Bracket

5| M6 Hexagonal Expansion

Screws

| 4| For installing the Mounting Bracket

to the wall/structure

6| RFID Card| 2| RFID Version Only
7| Allen Wrench| 1| For tightening M5 Screws
8| M5 Anti-Theft Countersunk

Head Screws

| 4| For securing the Plug Holster to the

Holster Bracket

9| M6 Anti-Theft Hexagonal

Expansion Screws

| 4| For installing the Holster Bracket to

the wall/structure

GATHER TOOLS

Tools required before installing the Wall-Mounted charger, gather the following tools:

1. Wire stripper
2. Adjustable Wrench M6
3. Voltmeter or digital multi-meter (for measuring AC voltage at the installation site)
4. Level
5. Pencil or marker
6. Drill
7. The inserting cable should meet the best waterproof performance. It is recommended to use 3 core /7AWG cable (XLPE or equivalent cable) to pull the cable from the distribution box.

PLAN THE MOUNTING

WARNING : In areas with frequent thunderstorms, add surge protection at the service panel for all circuits. Ensure all power and ground connections, especially those at the breaker and bus bar, are clean and tight.
CAUTION : An equipment-grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the product.not recommended to be installed in coastal environments with high humidity or high dust.

1. STEP 1
   Select the appropriate mounting location with electrical capacity:

2. Ensure the owner has chosen a mounting location that allows the charging cable to reach the car’s charging port while still providing slack.

3. The device must be anchored into mounting such as 2” x 4” stud or a solid wall.

4. The device shall be mounted at height between 2 feet (600 mm) and 4 feet (1200 mm) from ground.

5. Drill 4 Screw Holes with a diameter of 0.35” and a depth of 2.05” by using 2 mounting templates. Please drill screw holes in the direction of the template arrow. And use two templates at a horizontal distance around 12 feet.

6. MOUNT THE CHARGING STATION

7. Align the rear notch of charger with the wall-mounted bracket and fit the screw holes of the right and left side.

8. Tighten two M5 anti-theft screws to complete the installation.

9. WIRE THE CIRCUIT

   • WARNING: This device must be grounded. Disconnect electrical power prior to installing the charging station.
   • WARNING : Improper connection of the equipment-grounding conductor would result in a risk of electric shock. Check with a qualified electrician or serviceman if you are not sure whether the product is properly grounded. Do not modify the plug provided with the product – if it doesn’t fit the outlet, have a proper outlet installed by a qualified
     CAUTION : Use appropriate protection when connecting to the main power distribution cable.

10. For safe use of electricity, please set circuit breaker protection in the input part of EV Charger. The wiring is not complicated, just need to follow the instructions below: Connect the L1 lead to the grid L1, connect the L2 lead to the grid L2, connect the PE lead to the grid PE.

OPERATE YOUR DEVICE

• WARNING : This device should be supervised when used around children.
• CAUTION : Please use the charger properly. Do not hit or press hard on the enclosure. If the case is damaged, please contact a professional technician.

Operating Steps with Plug and Charge

1. STEP 1
   Standby Mode: After being powered on, the lights will be all on, green light (READY), green light turn to flash(CHARGE) and red light (FAULT). Then the blue light (READY) is constantly on in standby mode.

2. STEP 2
   Plug the Charging Connector: Please plug the charging connector into the vehicle charging inlet.

3. STEP 3

   • Charging : The green light (CHARGE) turns to flash automatically, charging is in process.
   • If the red light (FAULT) is on, plug the vehicle connector again.
   • If red light is still on, please refer to “Error and Warning Messages”.

4. STEP 4
   Charging finished: When the charging is finished, the green light (CHARGE) is constantly on, please press the button on connector and pull out the charging connector.

5. STEP 5
   Re-plug the charging connector: when you finish the charging process, please re-plug the charging connector back to the holster, you will hear a “click” sound.

Operating Steps with RFID
CAUTION : Please keep your RFID card properly to avoid unnecessary loss.

1. STEP 1
   Standby Mode: After power-on, green light (READY), green light turn to flash(CHARGE) and red light (FAULT) all on. The blue light (READY) is constantly on when in standby mode.

2. STEP 2
   Swipe the RFID Card: Please plug the charging connector into the vehicle charging inlet. Swipe the RFID card first and plug in the charging connector within 120 seconds, otherwise you need to swipe the RFID card again.

3. STEP 3
   Charging : The green light (CHARGE) turns to flash automatically, charging is in process.

   • If the red light (FAULT) is on, plug in the charging connector again.
   • If red light is still on, please refer to “Error and Warning Messages”.

4. STEP 4
   Charging finished: When the charging is finished, the green light (CHARGE) is constantly on, please press the button on connector and pull out the charging connector.

5. STEP 5
   Re-plug the charging connector : when you finish the charging process, please re-plug the charging connector back to the holster, you will hear a “click” sound.

LIGHT CODES

After Start UP

Error and Warning Messages

Input OVP

|

1 flash followed by 3 sec pause

|

Auto Recover

Input UVP

|

2 flashes followed by 3 sec pause

|

Auto Recover

Output OCP

|

3 flashes followed by 3 sec pause

|

Auto Recover

OTP

|

4 flashes followed by 3 sec pause

|

Auto Recover

RCD Abnormal

|

5 flashes followed by 3 sec pause

|

Auto Recover

Ground Fault

|

6 flashes followed by 3 sec pause

|

Auto Recover

Control Pilot Fault

|

Flicker

|

Auto Recover

MCU Self-Test Fail

|

Constantly Bright

|

Contact Customer Service

RCD Self-Test Fail

|

Constantly Bright

|

Contact Customer Service

Relay Self-Test Fail

|

Constantly Bright

|

Contact Customer Service

RCD Abnormal Stop Charging

|

Constantly Bright

|

Contact Customer Service

Output OCP Stop Charging

|

Constantly Bright

|

Contact Customer Service

OTP Stop Charging

|

Constantly Bright

|

Contact Customer Service

SMART APP GUIDE (OPTIONAL)

1. Download EV app.
2. Follow the tutorial in APP to connect your device.

FCC STATEMENT

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:
This device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation.

Caution : Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

To satisfy FCC RF exposure requirements, a separation distance of 20cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended.

WARRANTY AND MAINTENANCE

• The warranty period for this charger is two years.
• During the warranty period for any malfunction under normal use according to the User Manual and Service Instructions (to be determined by certified maintenance technicians of sellers), the product shall be repaired free of charge. Except for the following situations, the charger shall be subject to the above warranty terms:

1. The warranty certificate cannot be provided or the contents of the warranty certificate are modified or inconsistent with the label indication of the repaired product.
2. Those who are unable to provide valid proof of purchase.
3. Those who exceed the manufacturer’s specified warranty period.
4. Those who damage the product due to not following the product service instruction for use, maintenance and storage.
5. Damage or malfunction caused by external object entering.
6. Unauthorized repair, disassembly or modification.
7. Damage caused by force majeure (such as lightning, excessive voltage, earthquake, fire, flood, etc.).
8. Malfunction and damage caused by other unavoidable external factors. Malfunction and damage caused by improper use of equipment, such as water or other solutions entering into the equipment.
9. Malfunction and damage caused by the grid power supply and voltage which is not specified for use with the charger equipment.

The above guarantees shall be made solely, and no other express or implied warranties shall be made (including the implied warranties of merchant ability, particular and applicable reason- ableness and adaptability, etc.) whether in the contract, civil negligence, or other aspects, the Company shall not be responsible for any special, incidental or consequential damages.

FAQ

Q: Can I install the charging station myself?
A: No, the charging station should be installed by a qualified technician according to the user manual and local safety regulations.

Q: What should I do if I notice damage to the power cord or EV cable?
A: Do not use the product if the power cord or EV cable is damaged. Contact customer support for assistance.

Q: Is it safe to use the device with an extension cord?
A: No, to avoid a risk of fire or electric shock, do not use this device with an extension cord.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>