FLASHPOINT FPLFX600SE HSS Battery Powered Flash Instruction Manual

FLASHPOINT FPLFX600SE HSS Battery Powered Flash

Important Safety Instructions

This product is a piece of professional photographic equipment, to be operated by professional personnel only.
The following basic safety precautions must be followed when using this product: All transport protective materials and packaging on the product must be removed before use.

1. Carefully read and fully understand the instruction manual before use and strictly follow the safety instructions. Failure to do so may result in death, serious injury, damage to the product, or other property damage.
2. High voltage exists when the flash is powered on. Internal capacitors will remain charged for some time after the power is off.
3. This product is a professional lighting fixture, children are prohibited from using it. Children must be closely supervised by adults when approaching the fixture, to prevent collisions with the fixture or unauthorized use that could cause personal injury.
4. This is not an ordinary lighting fixture and must not be used for general illumination. Anyone with a history of eye damage or sensitivity should avoid using this fixture or looking directly at it.
5. Extreme caution must be exercised when using it, do not touch high temperature parts such as flash tubes to avoid burns.
6. Do not point the flash directly at the eyes (especially baby’s eyes) under any circumstances, as this could impair vision in a short time. Turn off immediately if discomfort occurs, stop using, and seek medical attention promptly.
7. If the flash tube is damaged, stop using it immediately and contact the manufacturer, service agent, or qualified repair personnel for a replacement to prevent accidents.
8. Do not use damaged equipment or accessories. Allow professional repair technicians to inspect and confirm normal operation before continuing use after repairs.
9. Disconnect the power source or remove batteries (if it has one) before replacing flash tube, protective glass, or fuses. Allowing 10 minutes to cool before replacing flash tube, and wear insulated or heat resistant gloves when operating.
10. Turn off power before connecting or disconnecting plugs from outlets. Ensure plugs are fully inserted when connecting.
11. Stop using immediately if the product shell is cracked due to falling, squeezing, or strong impact, to avoid touching the internal electronic components and getting an electric shock.
12. Some products have long power cords, please place them properly to avoid contact with heat sources or tripping others. It is recommended to use the original power cord. Damage caused by non-original cords is not covered by the warranty.
13. Unplug the equipment power plug from the power socket before cleaning or maintenance. Do not pull the power cord forcibly, use both hands to hold the plug end and pull it out.
14. This device is not waterproof. Keep it dry and avoid immersing it in water or other liquids It should be installed in a ventilated and dry location and avoid using it in rainy, humid, dusty, or overheated environments. Do not place items above the device or allow liquids to flow into it to prevent danger.
15. Do not disassemble without authorization. If the product malfunctions, it must be inspected and repaired by our company or authorized repair personnel.
16. Before storing the device, ensure it has completely cooled down and the power cord is unplugged, then put it in the protective case or a ventilated dry location.
17. Do not place the device near alcohol, gasoline, or other flammable volatile solvents or gases such as methane and ethane.
18. Do not use or store this device in potentially explosive environments.
19. Do not cover the heat dissipation port 1
20. Do not use accessories not been approved by our company, as this may cause fire, electric shock, or personal injury.
21. Clean gently with a dry cloth. Do not use a wet cloth as it may damage the device.
22. Some products are equipped with protective covers that must be removed before use.
23. This instruction manual is based on rigorous testing. Changes in design and specifications are subject to change without notice. Check the official website for the latest instruction manual and product updates.
24. Use only specified chargers and follow proper usage instructions for certain products with built-in lithium batteries, within the rated voltage and temperature range.
25. Some products are powered by lithium batteries, which have limited lifespans and will gradually lose their charging capacities, which is irreversible. As the battery ages, the product’s battery life will decrease.
    • The lifespan of a lithium battery is estimated to be 2 to 3 years. Please regularly check the battery, and if the charging time significantly increases or the battery life significantly decreases, consider replacing the battery.
26. Some products are equipped with lithium batteries. The following are the storage recommendations: Charge the battery to about 50% before storage. Charge it to about 50% at least every six months. Removable batteries should be stored separately.
    • The storage temperature should be between 0° C and 40° C.
27. Some products are powered by lithium batteries. Please note:
    • Do not disassemble, crush, or puncture the battery.
    • Avoid short-circuiting the battery contacts.
    • Do not expose the battery to fire or water.
    • Do not expose the battery to temperatures above 60° C.
    • Keep out of reach of children.
    • Protect the battery from excessive shock or vibration.
    • Do not use a damaged battery.
    • If the battery leaks, avoid contact with the leaking fluid.
    • If the battery fluid comes into contact with your eyes, immediately rinse with water for at least 15 minutes. Lift your eyelids until there are no signs of fluid and seek medical attention promptly.
28. Confirm and comply with all relevant local laws and regulations when handling any batteries.
29. The warranty period for this device as a whole is one year. Consumables (such as batteries), adapters, power cords, and other accessories are not covered by the warranty.
30. Unauthorized repairs will void the warranty and will incur charges.
31. Failures from improper operation are not covered under warranty.

Foreword

Thank You for Choosing

XPLOR 600 SE has strong power, an all-in-one lithium battery pack, and great portability. When using a 2.4G wireless R2 system, it can be triggered by an R2 / R2 Pro / R2 mark II/ R2 nano series flash trigger in M/Multi mode. With transmitter & receiver functions, XPLOR 600 SE can also be used in combination with camera flashes, outdoor flashes, studio flashes, etc. With this flash, your shooting will become simpler. With high-speed shooting throughout the process, a single fixture overshadowing the sunlight, a bare flash tube, and a standard reflector make a perfect match for outdoor and live shooting, XPLOR 600 SE is an ideal light source for freelance commercial photographers, journalists, and photography enthusiasts, wedding documentary photographers, etc.

Main Features

• Compatible wireless system: When using 2.4G wireless R2 system, fully supports M/Multi flash system of Canon, Nikon, Fujifilm, Olympus, Sony, Leica, Pentax, etc. Workable as a receiver unit in a wireless flash group.
• Simple operation: Steplessly rotatable select dial together with a colorful LCD panel.
• Distinct group colors: 16 groups with different colors to quickly distinguish even in remote distance usage.
• Built-in 2.4G wireless transmission: With all-in-one functions and 100 meters of further transmission.
• Studio quality light: Up to 600Ws, GN 87 (m ISO 700, with efficient reflector).
• Lightweight and portable: Simple usage and portability even with power and accessories.
• Detachable battery pack: Professional lithium battery pack (10.8V / 8940mAh), 0.0ls-1.9s recycle time, and 500 full power flashes.
• Wireless control: With a built-in 2.4G wireless R2 system to achieve wireless control, a 3.5mm sync cord jack to achieve various sync triggering modes.
• Wide-range accessories: The Bowens mount has wide compatibility.
• Precise power adjustment : From full power 7/7 to 7/256 with 0.1 increment each step.
• Advanced functions : 7/8000s high-speed sync, 40W LED modeling lamp.

Warning

• Always keep this product dry.
• Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center.
• Stop using this product if it breaks open due to extrusion, falling, or a strong hit. Otherwise, an electric shock may occur if you touch the electronic parts inside it.
• Do not leave or store the flash unit if the ambient temperature reads over 50° C.
• Do not fire the flash directly into the eyes (especially those of babies) within short distances. Otherwise, visual impairment may occur.
• Do not use the flash unit in the presence of flammable gases, chemicals, and other similar materials.
• In certain circumstances, these materials may be sensitive to the strong light emitting from this flash unit, and fire or electromagnetic interference may result.
• This product is not waterproof, do not use it in rain or damp conditions.
• Please remove the flash head protection cover before using it.

Name of Parts

Flash Body

1. Flash Tube
2. Bowens Mount
3. LCD Panel
4. MENU Button
5. MODE Button
6. Select Dial
7. SET Button
8. Power Switch/Test Button
9. Modeling Lamp Button
10. Knob
11. Bracket Sleeve
12. Group/Flash Ready Indicator
13. Accessory Lacking Pusher
14. Battery Compartment Pusher
15. Fan Inlet
16. Handle
17. Bracket Locking Knob
18. USB-C Port
19. 3.5 mm Sync Cord Jack
20. Photocell Receiver
21. Battery Charging Port
22. Battery Level Indicator
23. Battery Indicator Button

LCD Panel

1. M (Manual) Flash
2. Multi Flash
3. Photocell

Item List of XPLOR 600 SE

Item List of XPLOR 600 SE 2-light Kit

Installing and Disassembling Reflector

1. Installing: Press down the accessory locking pusher, insert the reflector into the accessory mount, and rotate clockwise to lock it up.
2. Disassembling: Press down the accessory locking pusher, and rotate the reflector anticlockwise to unlock.

Attaching and Detaching Flash Tube

1. Attaching: Press down the accessory locking pusher, and remove the reflector or other accessories. Match the flash tube in the tube socket and push until it is securely seated into the socket.
   • Note: Please wear gloves for the above operations.
2. Detaching: Press down the accessory locking pusher, and remove the reflector or other accessories. Grasp the flash tube and pull it out horizontally.
   • Note: Please wear gloves for the above operations.

Adjusting Flash Angle

1. When the handle fixing fastener is not pulled out, rotate the handle anticlockwise to unlock it, adjust the flash body for the desired angle, and then rotate the handle clockwise to tighten.
2. If the handle collides the flash body in rotation, please press the handle fixing fastener and pull out the handle, repeat step 1 after stretching out a few distances.

Power Switch

1. Long press the power switch button for 2s until the unlock icon is displayed on the panel, then rotate the select dial clockwise to turn on the device.
2. Long press the power switch button for 2s until the panel blackouts to turn off the device.
   Note: Turn off the device if it will not be used for an extended period. This device is designed with an automatic power-off function, which can be set in the menu settings.

Battery

Features

1. This flash unit uses a lithium battery which has a long runtime. The available charge-and-discharge times are 500.
2. It is reliably safe. The inner circuit is against overcharge, overdischarge, overcurrent, and short circuits.
3. It takes only 4 hours to fully charge the battery by using the standard battery charger.

Cautions

• Do not short circuit.
• Do not be exposed to rain or immerse in water. This battery is not waterproof.
• Keep out of reach of children.
• No over 24 hours’ continuous charging.
• Store in dry, cool, ventilated places.
• Do not put aside or into the fire.
• Dead batteries should be disposed of according to local regulations.
• If the battery has ceased use for over 3 months, please make a full recharge.

Loading and Unloading the Battery

1. Loading: Match the battery’s groove with the main battery compartment’s ridge. Push down the battery pack until it is locked.
2. Unloading: Push the battery compartment pusher and the battery pack upward at the same time to unload it.

Battery Level Indication

Attach the battery pack to the flash correctly. Check the battery level by pressing the battery indicator button and lightening the battery level indicator as the following table shows.

Battery Level Indicator on the Battery (Indicating battery level and management of non-loaded battery)| Meaning
---|---
1 red grid +3 green grids| 75% – 700% battery level
1 red grid +2 green grids| 50% – 75% battery level
1 red grid +1 green grid| 25% – 50% battery level
1 red grid| 3% – 25% battery level
2% flash red, 1% off| The battery level is going to be used out immediately. And the flash will auto power off in 1 minute.

Note: Please recharge the battery as soon as possible (within 10 days). Then, the battery can be used or be placed for long period

Note: The two indications are almost the same except for the grid shift.

Wireless Flash Mode

XPLOR 600 SE can only be set as a receiver unit (receiver end) by setting to the wireless transmission it will automatically switch among different camera systems’ M/multi flash modes according to R2 series flash triggers.

High-Speed Sync

High speed sync (FP flash) enables the flash to synchronize with all camera shutter speeds. This is convenient when you want to use aperture priority for fill-flash portraits.

1. Press the MENU button to enter the menu interface, turn the select dial, and press the SET button to enter high-speed sync and turn on it. Then press the MENU button to return to the main interface, the HSS icon can be seen on the panel.
2. Please refer to the R2 series flash triggers.
   • If you set a shutter speed that is the same as or slower than the camera’s maximum flash sync speed, will not be displayed in the viewfinder.
   • With high-speed sync, the faster the shutter speed, the shorter the effective flash range.
   • To return to normal flash, turn off the high-speed sync function in the menu settings. Then will disappear.
   • Multi flash mode cannot be set in high-speed sync mode.
   • Over-temperature protection may be activated after 100 consecutive high-speed sync flashes.

M: Manual Flash

• The flash output is adjustable from 1/1 full power to 1/256 power with a 0.1 step increment. To obtain a correct flash exposure, use a hand-held flash meter to determine the required flash output.
• Press the MODE button so that < M > is displayed. Turn the select dial to choose a desired flash output amount.

Flash Output Range

• The following table makes it easier to see how the step changes in terms of aperture value when you increase or decrease the flash output.
• Turn the select dial clockwise to increase the flash output, while turning it anticlockwise to decrease the flash output.

Optical S1 Secondary Unit Setting

• Press the < MENU > button to enter photocell to choose the Sl function, so that this flash can function as an optical Sl secondary flash with an optical sensor in M manual flash mode. Then press the MENU button to return to the main interface.
• With this function, the flash will fire synchronously when the main flash fires, the same effect as that by the use of wireless triggers. This helps create multiple lighting effects.

Optical S2 Secondary Unit Setting

• Press < MENU > button to enter photocell to choose the S2 function, so that this flash can also function as an optical S2 secondary flash with the optical sensor in M manual flash mode. Then press the MENU button to return to the main interface.
• This is useful when cameras have a pre-flash function. With this function, the flash will ignore a single “preflash” from the main flash and will only fire in response to the second, actual flash from the main unit.
• Sl and S2 optic control triggering is only available in M manual flash mode.

Display Flash Duration

• Flash duration refers to the length of time that from the flash’s firing to reach the half peak at maximum. The half peak at maximum is usually expressed as t=0.5.
• In order to provide the photographer with more concrete data, this product adopts t=O.l. The difference between t=0.5 and t=O.l is shown in the following picture.
• Turn off the high-speed sync function in M mode, the flash duration will also be displayed.

Multi: Stroboscopic Flash

• With stroboscopic flash, a rapid series of flashes is fired. It can be used to capture multiple images of a moving subject in a single photograph.
• You can set the flash output, number of flashes, and flash frequency (number of flashes per sec. expressed as Hz).

1. Press the MODE button so that < Multi > is displayed, turn the select dial to choose a desired flash output.
2. Press the SET button and turn the select dial to set the number of flashes.
3. Press the SET button and turn the select dial to set the flash frequency.

Calculating the Shutter Speed

• During stroboscopic flash, the shutter remains open until the firing stops. Use the formula below to calculate the shutter speed and set it with the camera.

Number of Flashes/ Flash Frequency = Shutter Speed

• For example, if the number of flashes is 10 and the flash frequency is 5 Hz, the shutter speed should be at least 2 seconds.
• To avoid overheating and deteriorating the flash head, do not use stroboscopic flash more than 10 times in succession. After 10 times, allow the camera flash to rest for at least 15 minutes.
• If you try to use the stroboscopic flash more than 10 times in succession, the firing might stop automatically to protect the flash head. If this happens, allow at least 15 minutes’ rest for the camera flash.
• Stroboscopic flash is most effective with a highly reflective subject against a dark background.
• Using a tripod and a TTL flash trigger is recommended.
• A flash output of 1/1 and 1/2 cannot be set for stroboscopic flash.
• Stroboscopic flash can be used with “BULB”.
• If the number of flashes is displayed as “–“, the firing will continue until the shutter closes or the battery is exhausted. The number of flashes will be limited as shown by the following table.

Maximum Stroboscopic Flashes:

Flash /Hz Output|  | 2| 3| 4| 5| 6- 7| 8- 9
---|---|---|---|---|---|---|---
1/4| 7| 6| 5| 4| 4| 3| 3
1/8| 14| 14| 12| 10| 8| 6| 5
1/16| 30| 30| 30| 20| 20| 20| 10
1/32| 60| 60| 60| 50| 50| 40| 30
1/64| 90| 90| 90| 80| 80| 70| 60
1/128| 100| 100| 100| 100| 100| 90| 80
1/256| 100| 100| 100| 100| 100| 90| 80
Flash/Hz Output| 10| 11| 12- 14| 15- 19| 20-50| 60- 100
---|---|---|---|---|---|---
1/4| 2| 2| 2| 2| 2| 2
1/8| 4| 4| 4| 4| 4| 4
1/16| 8| 8| 8| 8| 8| 8
1/32| 20| 20| 20| 18| 16| 12
1/64| 50| 40| 40| 35| 30| 20
1/128| 70| 70| 60| 50| 40| 40
1/256| 70| 70| 60| 50| 40| 40

Wireless 2.4G Transmission

• XPLOR 600 SE adopts a 2.4G wireless R2 system, which has good  compatibility with other products. It can automatically switch to receiver unit according to the transmitter unit instead of setting manually. The compatible cameras include Canon, Nikon, Sony, Olympus, Panasonic, Fujifilm, Pentax, Leica, etc.
• Note: As a receiver unit, XPLOR 600 SE can be controlled by the following transmitter units: R2 XPRO II series, R2 nano series, R2 mark II series, Zoom Li-on X Pro series, Zoom Li-on X series and Zoom Li-on Ill series.

Wireless Settings

• Press the MENU button to enter the menu interface, turn the select dial, and press the SET button to choose among wireless/ group/ channel/ ID/ wireless sync, then turn the select dial and press the SET button to adjust the parameters.
• Press the MENU button to return to the previous menu, and press again to return to the main interface.
• If there are other wireless flash systems nearby, you can change the channel to prevent signal interference. The channels of the transmitter unit and the receiver unit(s) must be set to the same.
• Group Adjustment Range: 0-9, A-F
• Channel Adjustment Range: 1-32
• ID   Adjustment Range: off, 1-99
• Wireless   Sync: press the SET button.

Take the X3 flash trigger as an example:

1. Turn off the camera and mount the flash trigger on the camera hot shoe. Then, power on the flash trigger and the camera.
2. Slide the screen of X3 down from the top to display < Setting >, press < Setting > to enter C. Fn. menu, then press < Wireless > to set CH and ID. Slide the screen from the left to the right to return to the main interface, on which you can set the flash mode and output power level of groups.
3. Press the MENU button of XPLOR 600 SE to select wireless and turn it on, then set the CH and ID the same as the flash trigger
4. Press the wireless sync on the trigger and flash, then press the SET button on the flash can set their CH and ID to the same.
5. Press the camera shutter to trigger.

Wireless Flash Shooting

Positioning and Operation Range  Example of wireless flash shooting

• Auto flash shooting with one receiver unit
• Please use the transmitter unit with a wireless transmission function.
• Before shooting, perform a test flash and test shooting.
• The transmission distance might be shorter depending on the conditions such as positioning of receiver units, the surrounding environment and weather conditions.

Wireless Multiple Flash Shooting

• You can set and shoot with a different flash mode for each firing group (upto to 16 groups).
• Auto flash shooting with two receiver units.
• Auto flash shooting with three receiver units

The Reason & Solution for Not Triggering in Flashpoint 2.4G Wireless

1. Disturbed by the 2.4G signal in an outer environment (e.g. wireless base station, 2.4G wifi router, Bluetooth, etc.)
   • To adjust the channel CH setting on the flash trigger (add 10+ channels) and use the channel that is not disturbed. Or turn off the other 2.4G equipment in working.
2. Please make sure that the flash has finished its recycling or caught up with the continuous shooting speed or not (the flash ready indicator is lightened) and that the flash is not under the state of over-heat protection or other abnormal situations.
   • Please downgrade the flash power output. If the flash is in Multi mode, please try to change it to M mode.
3. Whether the distance between the flash trigger and the flash is too close or not(< 0.5m).
   • R2 Series: Press and hold the triggering button then turn on the device, until the indicator blinks twice.
   • R2 Pro Series: Please set the C.Fn-DIST to 0-30m.
4. Whether the flash is in the low battery states or not.
   • Please charge or replace the battery in time.

Modeling Lamp

• XPLOR 600 SE is equipped with a 40W LED modeling lamp. Press the modeling lamp button to enter modeling lamp settings, turn the select dial to choose among off/free/prop, then turn the select dial and press the SET button to adjust the parameters.
• Press the modeling lamp button to return to the main interface.

Setting Custom Functions

Sync Triggering

The sync cord jack is a <!J3.5mm plug. Insert a trigger plug in and the flash will be fired synchronously with the camera shutter.

Protection Functions

1. Over – Temperature Protection
   • To avoid overheating and deteriorating the flash head, do not fire more than 100 continuous flashes in fast succession at 1/7 full power. After 100 continuous flashes, allow a rest time of at least 10 minutes.
   • If you fire more than 100 continuous flashes and then fire more flashes in short intervals, the inner over-temperature protection function may be activated and make the recycling time over 10 seconds. If this occurs, allow a rest time of about 10 minutes, and the flash unit will then return to normal.
   • When the over-temperature protection is started is shown on the LCD display.
   • Number of flashes that will activate over-temperature protection:
     Power Output Level| Number of Flashes
     ---|---
     1/1| 100
     1/2 (0 1-0 9)| 200
     1/4 (01-09)| 265
     1/8 (0 1-0 9)| 400
     1/16(01-0 9)| 530
     1/32 (0 1-0 9)| 665
     1/64 (0 1-0 9)| 1330
     1/128 (0 1-0 9)
     1/256 (0 1-0 9)
   • Number of flashes that will activate over-temperature protection in high-speed sync triggering mode:
     Power Output Level| Number of Flashes
     ---|---
     1/1| 65
     1/2 (0 1-0 9)| 80
     1/4(01-0 9)| 100
     1/8(01-0 9)| 130
     1/16(01-0 9)| 160
     1/32 (0 1-0 9)| 200
     1/64 (0 1-0 9)
     1/128(01-0 9)| **** 265
     1/256 (0 1-0 9)
2. Other Protections
   • The system provides real-time protection to secure the device and your safety. The following lists prompts for your reference.
     Display| Meaning
     ---|---
     El| A failure occurs on the recycling system so that the flash cannot fire. Please restart the flash unit. If the problem still exists. please send this product to a maintenance center.
     E2| The system gets excessive heat. Please allow a rest time of 10 minutes.
     E3| The voltage on two outlets of the flash tube is too high Please send this product to a maintenance center.
     E9| There are some errors that occurred during the upgrading process. Please use the correct firmware upgrade method.

Technical Data

Specifications and data may be subject to changes without notice.

Firmware Upgrade

• This flash supports firmware upgrades through the USB port. Update information will be released on our official website.
• The USB connection line is not included in this product. The USB port is a standard USB-C socket. A Common USB connection line is applicable.

Maintenance

• Shut down the device immediately should abnormal operation be detected.
• Avoid sudden impacts and the product should be deducted regularly.
• It is normal for the flash tube to be warm when in use. Avoid continuous flashes if unnecessary.
• Maintenance of the flash must be performed by our authorized maintenance department which can provide original accessories.
• This product, except for consumables e.g. flash tubes, is supported with a one-year warranty.
• Unauthorized service will void the warranty.
• If the product has failures or was wetted, do not use it until it is repaired by professionals.
• Changes made to the specifications or designs may not be reflected in this manual.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Limited Warranty

One Year Flashpoint Limited Warranty

• Flashpoint warrants to the original purchaser that your Flashpoint product shall be free from defects in material and workmanship for the period of one (1) years from the date of purchase (or delivery as may be required in certain jurisdictions), or thirty (30) days after replacement, whichever comes later.
• Flashpoint’s entire liability and your exclusive remedy for any breach of warranty shall be, at Flash point’s option, to repair or replace the hardware, provided that the hardware is returned to the point of purchase or such other place as Flashpoint may direct with a copy of the sales receipt or dated itemized receipt. Flashpoint may, at its option, replace your product, offer to provide a functionally equivalent product, or repair any product with new, refurbished or used parts as long as such parts are in compliance with the product’s technical specifications. Any replacement hardware product will be warranted for the remainder of the original warranty period or thirty (30) days, whichever is longer, or for any additional period of time that may be applicable in your jurisdiction. If the product has been discontinued, the warranty provider reserves the right to replace it with a model of equivalent quality and function.
• This warranty does not cover problems or damage resulting from accident, abuse, misapplication, or any unauthorized repair, modification or disassembly, improper operation or maintenance, normal wear and tear, or usage not in accordance with product instructions or connection to improper voltage supply, use of consumables, such as replacement batteries, not supplied by Flashpoint, except where such restriction is prohibited by applicable law.
• Except where prohibited by applicable law, this warranty is nontransferable and is limited to the original purchaser and the country in which the product was purchased. This warranty gives you specific legal rights, and you may also have other rights, including a longer warranty duration that may vary under local laws.
• To start a warranty claim contact the Flashpoint Customer Service Department to obtain a return merchandise authorization (“RMA”) number, and return the defective product to Flashpoint, along with the RMA number and proof of purchase.
• Question about our product line?
• Need Product Support?
• We are proud of our products and celebrate our customers.
• We are with you, from product selection to everyday use.
• Be secure with your purchase and reach us as you need.
• 212-647-9300 all support@flashpointlighting.com
• Q Flashpoint,
• 42 West 18th Street, New York, NY 70071
• You can always contact us at BRANDS@ADORAMA.COM for personal technical support.
• Our website contains a wide range of Support and FAQ pages with valuable technical assistance.
• Flashpoint is a registered trademark of ADORAMA CAMERA.
• © 2024 Adorama Camera, Corp.
• All Rights Reserved.
• WWW.FLASHPOINTLIGHTING.COM
• Scan to join our Instagram community for product tips, Inspirations, and more.

Documents / Resources

| FLASHPOINT FPLFX600SE HSS Battery Powered Flash [pdf] Instruction Manual
FPLFX600SE HSS Battery Powered Flash, FPLFX600SE, HSS Battery Powered Flash, Battery Powered Flash, Powered Flash, Flash
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>