HIGH TECH PET PX-1, PX-2 Power Pet Main Circuit Board Owner’s Manual

HIGH TECH PET PX-1, PX-2 Power Pet Main Circuit Board

Product Specifications

• Models: PX-1 & PX-2
• Compatible Circuit Boards: PCB-PX & PCB-PX-WF
• Manufacturing Location: U.S.A.

Product Usage Instructions

Main Circuit Board Replacement

Ensure to follow these steps for replacing the main circuit board:

1. Step 1: Remove range knobs from the control panel.
2. Step 2: Remove the door from the wall and lay it flat on a soft surface with the inside facing down.
3. Step 3: Remove all screws, separating the larger flat head screws located at the top of the door.

Pet Door Board Replacement

Follow these steps for replacing the pet door board:

1. Step 1: Remove the door from the wall and lay it flat with the inside facing down.
2. Step 2: Remove all screws, keeping separate the larger flat head screws at the top of the door.

Frequently Asked Questions (FAQ)

1. Q: What should I do if I encounter resistance while lifting the edge of the board during replacement?
   A: Ensure that the adjustment knobs are free before lifting the edge. If there is resistance, gently pry off the hidden adjustment knobs first.

2. Q: How can I verify the correct installation of the adjustment knobs after replacement?
   A: Follow the provided steps to re-install the adjustment knobs with proper orientation and check if they operate correctly by testing the door’s functionality.

Pet Door Board Replacement Instructions

*Remove both range knobs from control panel before starting replacement.

1. Remove door from wall and lay flat on carpeting or towels, with the inside of the door facing down.

2. Remove all the screws, keeping separate the six larger flat head screws located toward the top of the door. Separate and remove the backing frame from the door.

3. Locate the green circuit board at the top of the door. Using needle nose pliers, remove the two connectors from the board, taking care not pull on the wires themselves, and not to crush the connector body with too much clamp force. The large black connector has a plastic latch in the center of one side that has to be depressed as shown below while disconnecting.

4.  Remove the four board mounting screws and lay them aside from the other screws in the frame.

5. Carefully lift the very top edge of the board top and pry off the hidden adjustment knobs allowing them to drop beneath the door. Then remove the board completely from the door.
   Note 1: There will be some resistance to lifting the edge of the board until the knobs are free.
   Note 2: E nsure all five plastic push buttons are still centered in their respective holes of the door panel.

6. Carefully position the replacement board without disturbing the plastic push buttons and secure with two of the four screws.
   CAUTION: Do not over-tighten the four mounting screws. Slightly snug is all that is required.

7. Peek under the door to see that all the buttons are still in place and to collect the two adjustment knobs. Finish the rest of the screws, again making sure to tighten gently.

8. Attach the two connectors and ensure that none of the pins are pushed back out of the connector shell during this process. lf necessary use a small flat-head screwdriver to re-seat the pins in the shell.

9. Re-attach the backing frame to the door, using all of the removed screws.
   CAUTION: Do not over-tighten the pan-head screws – moderately snug is sufficient.

10. Re-install the two adjustment knobs with the pointers properly oriented as follows.

    • Turn the door over and look in the knob holes to locate the hexagon receptacle for the knob shafts.
    • One at a time press the knob into its receptacle just enough to engage, and then gently turn the knob clockwise until it reaches its rotational limit.
    • Remove the knob and re-insert it gently in the receptacle with the pointer of the knob now pointing to approximately the MAX setting. Then turn the knob fully counter-clockwise and confirm the pointer is approximately at the MIN setting. lf not, repeat this step with slightly more insertion and rotation force.
    • Finally, press on the knobs until they are fully seated. NOTE: It is recommended that you check the operation of the door prior to re-installing in the following manner.
    • Lean door against a wall, plug in the power supply, press the ON button and press the OPEN button, ensuring the door opens and closes normally.
    • Enable only the inside sensor and using a working collar, insure the door opens from the inside.
    • Enable only the outside sensor turn the door around and insure the door opens from the outside.

11. Re-install the working door.

NOTE: Recommended Range Knob Settings with the new board installed:
start with the Inside and Outside Range Knob settings at the top center (middle) setting. From there adjust sensitivity to your environment as needed.

PX Circuit Board **

**

PCB-PX & PCB-PX-WF

Caution: As with any pet door, supervision of your pet is advised. Failure to do so could result in harm to your pet. Please be sure to provide water and shade outside in the rare event that the electronic door fails to open.

We’re here to help!
1-800-255-1279

www.hightechpet.com

High Tech Pet Products, Inc.
2111 Portola Rd suite A
Ventura, CA 93003

References

• Electronic Pet Doors, Dog Fences, Bark & Training Collars

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>