Voice Comm Q2SST Wireless Charger,Power Cable User Manual
- September 20, 2024
- Voice Comm
Table of Contents
Voice Comm Q2SST Wireless Charger,Power Cable
Thanks for choosing us!
This product is a 3 in 1 wireless charger, support phone/Airpods/Apple Watch
charging at the same time.
Please kindly read the user manual before using and keep it for future
reference.
Specification
Input: 5 V 3A, 9V 3A, 12V 2.5A
Output (Phone): 15W Max
Output (Apple Watch): 3W
Output (Airpods ): 5W
Charging distance: ≤ 1omm
Conversion : ≥72%
NW: 282g
Dimensions: 93149163mm
Charging Mode
- Make sure the wireless charger dock connect to the power supply.
- Put the smartphone/Airpods/Apple Watch properly on the transmitter.
Notes
- Do not squeeze or collisions.
- Do not disassemble or throw into fire or water, to avoid causing a short circuit leakage.
- Do not use wireless charger in severely hot, humid or corrosive environments, to avoid circuit damage and occurs leakage phenomenon.
- Do not place too close with magnetic stripe or chip card ( ID card, bank cards, etc.) to avoid magnetic failure.
- Please keep the distance at least 20 cm between implantable medical devices ( pacemakers, implantable cochlear, etc.) and the wireless charger, to avoid potential interference with the medical device.
- To take care of the children, to ensure that they won’ t play the wireless charger as a toy, to avoid unnecessary accidents.
CE Maintenance
- EUT Operating temperature range: -10° C to 35° C.
- The device complies with RF specifications when the device used at 20mm from your body.
Declaration of Conformity
Voice Comm, LLC hereby declares that this Q2SSTAND3-266626 Ventev Qi2 wireless 3 in 1 Desk Mount is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. ln accordance with Article 10 (2) and Article 10(10), This product is allowed to be used in all EU member states.
Frequency Band(s):| Coil1: For Phone: 113kHz-205kHz,360kHz
Coil2: For Earphone: 113kHz-205kHz
Coil3: Watch: 300kHz-350kHz
---|---
Corrected Amplitude H-field:| Coil1: 111kHz-205kHz: 21.64dBuNm; 360kHz:21.16
dBuA/m
Coil2: 21.92dBuA/m
Coil3:18.0ldBuA/m
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the
following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radiofrequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The FCC certification of this device refers to RF exposure testing performed in typical operating conditions, where a person is no closer than 20 centimeters from the device surface at all times, except for non-repetitive patterns with transient time intervals in the order of a second. Only in the stated conditions, the device is shown to fully comply with the FCC RF Exposure requirements of KDB447498.
The involved images are sketch maps, the final product as per the material
subjects.
Includes: wireless charger, Power cable, user’s manual.