RIPLEY MSAT 5 Mid-Span Access Tool Instructions
- September 18, 2024
- RIPLEY
Table of Contents
RIPLEY MSAT 5 Mid-Span Access Tool
Product Information
Specifications:
- Product Name: MSAT 5 Mid-Span Access Tool
- Applicable Buffer Tube Sizes: 1.9mm – 3.0mm in diameter
- Blade Type: #2 Phillips screwdriver
- Warranty: 1 year against defective materials and workmanship
Product Usage Instructions
- Preparing Cable for Midspan Access: Expose the buffer tube as needed.
- Using the Tool: Utilize the sizing channels on the top of the tool to determine the appropriate slot for the buffer tube size.
- Blade Replacement:
- Note: Handle blades with caution and dispose of used blades properly.
- Carefully observe blade placement as shown in Figure 5. Ensure the front blade corners rest against the molded step in the tool body.
- Use a #2 Phillips screwdriver to remove the two screws in the blade cover.
- Remove the old blade.
- Install the new blade following the instructions in Fig 5. Reinstall the blade cover and screws.
Warranty Information:
RIPLEY warrants its products against defective materials and workmanship
for a period of one year from the date of shipment from the RIPLEY factory,
provided that the product is utilized in accordance with instructions and
specified ratings.
Frequently Asked Questions (FAQ):
-
Q: Can this tool be used on live electrical circuits?
A: No, this tool should not be used on live electrical circuits as it is not protected against electrical shock. -
Q: What sizes of buffer tubes is the MSAT 5 applicable to?
A: The MSAT 5 is applicable to buffer tubes ranging from 1.9mm to 3.0mm in diameter. -
Q: How long is the warranty for this product?
A: The warranty period for this product is one year from the date of shipment from the RIPLEY factory.
Warning! This tool should not be used on live electrical circuits. It is not protected against electrical shock! Always use OSHA/ANSI or other industry approved eye protection when using tools. This tool is not to be used for purposes other than intended. Read carefully and understand the instructions before using this tool.
The MSAT 5 Mid-Span Access Tool is designed to allow easy access to the fibers in multiple buffer tube sizes, all with no adjustments or die changes. The tool is applicable to buffer tubes 1.9mm – 3.0mm in diameter.
Operating Instructions
- Prepare cable for midspan access by exposing the buffer tube as needed.
- Use the sizing channels on the top of the tool to determine which slot on the tool to use. Starting with the smallest channel (#5) find the first slot the tube fits easily and fully seats into, then use the corresponding channel for your access. (Fig.1)
- Unhook the clasp and open the tool. Use caution to not contact the exposed blade.
- Place the buffer tube into the correct channel as determined in Step 2. (Fig.2)
- Close the tool completely until the clasp engages. (Fig.3)
- With a slow, even, and steady force, glide the tool along the tube in a smooth motion. The tool will slit the tube as shown in top feature photo.
- When you reach the end of the access point, cut off the scrap portion of tube before opening or removing the tool. (Fig.4). Use Miller 9150 diagonal cutter.
- Carefully open the tool and remove the buffer.
- After each use, carefully and thoroughly clean the tool and store it to protect from dirt.
Blade Replacement
Note: Use caution when handling blades and dispose of used blades properly
- Carefully observe blade placement as shown in Figure 5. The front blade corners rest against the molded step in the tool body.
- Use #2 Phillips screwdriver to remove the two screws in the blade cover.
- Remove old blade.
- Install new blade and locate it as shown in Fig 5. Reinstall blade cover and screws.
WARRANTY
RIPLEY warrants its products against defective materials and workmanship for a period of one year from date of shipment from the RIPLEY factory provided the product is utilized in accordance with instructions and specified ratings.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>