Junlan TTSB23-DD Wood Grain and Brass Finish Sound Bar Instruction Manual

Junlan TTSB23-DD Wood Grain and Brass Finish Sound Bar

FAQs

• Q: What should I do if the sound bar is not pairing with my device?
  • A: Make sure the sound bar is in pairing mode (indicated by a flashing light) and that your device’s Bluetooth is enabled. Try moving the devices closer together and ensure there are no obstructions causing interference.
• Q: How can I clean the Wood Grain & Brass Finish Sound Bar?
  • A: Use a soft, dry cloth to gently wipe down the exterior of the soundbar. Avoid using any harsh chemicals or abrasive materials that may damage the finish.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). NO USER-SERVICEABLE PART INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

• DANGEROUS VOLTAGE: The lightning flash with the arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to a person.
• ATTENTION: The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
• WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
• WARNING: USE UNDER SUPERVISION OF AN ADULT DUE TO LONG CORD This unit has a long cord that can be easily tripped on or pulled on, causing injury. Please make sure it is arranged so that it will not drape over a tabletop, etc. Where it can be pulled on by children or tripped over accidentally.

FCC

FCC STATEMENT:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution:

Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.

1. Read Instructions: All the safety and operating instructions should be read before the appliance is operated.
2. Retain Instructions: The safety and operating instructions should be well-kept for future reference.
3. Heed Warnings: All warnings on the appliance and in the operating instructions should be adhered to.
4. Follow Instructions: All operating and use instructions should be followed.
5. Power Sources: The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance.
6. Power-Cord Protection: Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point at which they exit from the appliance.
7. Overloading: Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
8. Grounding or Polarization: Precaution should be taken to ensure that the grounding or polarization means of an appliance are not defeated.
9. Severe weather: In extreme weather such as lightning storms, or hurricanes, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the appliance due to unexpected power surges.
10. Water and Moisture: The appliance should not be used near water-for example, near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool, or a wet basement.
11. Heat: The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
12. Object/Liquid Entry: Care should be taken so that no object/liquid enters into the enclosure through openings.
13. Ventilation: The appliance should not be situated so that its location (on a bed, sofa, rug, or similar surface) or position (such as a bookcase or cabinet) interferes with its proper ventilation.
14. Mounting: The appliance should be mounted only as recommended by the manufacturer.
15. Cleaning: Only use a soft dry cloth to clean the appliance.
16. Servicing: The user should not attempt to service the appliance beyond that described in the user’s operating instructions. All other servicing should be referred to qualified personnel.
17. Damage Requiring Service: The appliance should be serviced by qualified service personnel when:
    • The power supply cord or plug has been damaged.
    • Objects have fallen into, or liquid has been spilled into the appliance enclosure.
    • The appliance has been exposed to rain.
    • The appliance has been dropped, or the enclosure damaged.
    • The appliance does not appear to operate normally or exhibits a marked change in performance.
18. Non-use Periods: The power cord of the appliance should be unplugged from the outlet/The batteries should be removed when the appliance is to be left unused for a long period of time.

PRODUCT OVERVIEW

1. Power/Play/Pause button
2. Volume+/Next button
3. Volume-/Previous button
4. MODE button
5. DC IN port
6. AUX port
7. OPTICAL port
8. HDMI ARC port
9. Indicator
10. Remote sensor
    • REMOTE CONTROL
11. Power on/off button
12. Play/Pause button
13. Previous button
14. BT button
15. BASS button
16. Mute button
17. Vol+ button
18. Next button
19. Vol- button
20. EQ(equalizer) button
21. MODE button
22. TREBLE button

BATTERY INSTALLATION OF REMOTE CONTROL

1. Slide and lift the battery door.
2. Install 2 x AAA 1.5V carbon-zinc batteries (included) into the battery compartment as indicated by the polarity markings.
3. Close the battery door.

Caution:

1. Use only the size and type of battery specified.
2. Be sure to follow the correct polarity when installing the battery as indicated in the battery compartment, a reserved battery may cause damage to the device.
3. Do not mix different types of batteries (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.
4. If the batteries in the device are consumed or the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible leakage.
5. Do not try to recharge the battery not intended to be recharged; it can overheat and rupture. (Follow battery manufacturer’s instructions)
6. The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
7. Clean the battery contacts and also those of the device prior to battery installation.
8. Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.

Remote control operation range

• When there is an obstacle between the remote and the receiver, the unit may not operate.
• When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong light shines on the REMOTE SENSOR of the unit, the operation of the remote may be unstable.

PLACEMENT AND MOUNTING

1. Placing the device on a table – Ventilation
   • When placing the Soundbar on an entertainment center, bookshelf, or any type of enclosed space, be sure to allow at least 2-3 inches of space around the soundbar for ventilation. If the Sound Bar is enclosed in a tight space, without ventilation, heat generated from the Sound Bar could produce a potential heat hazard.
2. The Installation Distance
   • Mounting to a wooden wall
   • A. Mark the position of the mounting screws on the wall using a pencil.
   • B. Drill the screws directly into the marks that you have made on the wall and leave approx. 0.3 inches in length to hook the soundbar.
   • C. Put the sound bar onto the mounting screws. Make sure they are firm and stable.
   • Mounting to a brick wall
   • A. Mark the position of the mounting screws on the wall using a pencil.
   • B. Drill 2 holes in the wall with a powerful electric drill.
   • C. Insert the fixing plug and hammer into the holes.
   • D. Secure the screws into the fixing plug and leave approx. 0.3 inches in length to hook the soundbar.
   • E. Put the sound bar onto the mounting screws. Make sure they are firm and stable.

GENERAL OPERATION

1. Connect the AC/DC adapter to the unit and the indicator in front of the unit will light red.
2. Press the button on the unit or remote control to power on the unit and the sound “Power on” and “Bluetooth” (default mode) can be heard; press and hold the same button for about 3 seconds to power off and a sound “Power off” can be heard.
3. Press the Vol+ or Vol- button on the unit or remote control to adjust the volume level.
4. Press the MODE button on the unit or remote control to switch to a different mode.
5. During playback:
   • Press the Mute button on remote control to turn on or off the sound.
   • Press the EQ button on remote control repeatedly to change the EQ effect(Music/ Movie/ Bass/News/ Game); press and hold the EQ button to switch to default EQ effect.
   • Pressing the BASS button can change to BASS effect.
   • Pressing the TREBLE button can change to TREBLE effect.
6. When playing in Bluetooth mode:
   • Press and hold or button to skip to previous or next track; pressing the same button on remote control can also skip tracks.
   • Press button on unit or remote control to play or pause the track.

Note:

• It defaults Bluetooth mode when the unit is turned on.
• It will enter standby mode without signal input in 15 minutes, the indicator will turn to red and you can hear “Power off”.
• When the unit is muted, the indicator will blink.

AUX FUNCTION

1. Connect one end of the AUX cable to the AUX port of the unit, and the other end to the 3.5mm earphone jack or AUX out port of the external device.
2. Power on the unit and switch to AUX mode as previously mentioned and you will hear the sound “Auxiliary”, the indicator will light green.
3. Start the playback on an external device.
   • Note: The , and button on both the unit and remote control do not work in this mode.

HDMI ARC FUNCTION

1. Connect one end of the HDMI cable (not included) to the HDMI ARC port of the unit, and the other end to the HDMI ARC port of the TV.
2. Power on the unit and switch to HDMI mode as previously mentioned and you will hear the sound “HDMI”, the indicator will light white.
3. Start the playback on the TV.

Note:

• The TV must have ARC capability and be connected to HDMI ARC port.
• If there is no audio output(only picture) or sound when your TV is connected to the unit, please check the TV audio setting and try to set the audio output to other format.
• The , and button on both the unit and remote control do not work in this mode.

OPTICAL FUNCTION

1. Connect one end of the Optical cable (not included) to the OPTICAL port of the unit, the other end to the OPTICAL OUT port of the TV or DVD player, etc.
2. Power on the unit and switch to OPTICAL mode as previously mentioned and you will hear the sound “OPTICAL”, the indicator will light purple.
3. Start the playback on a TV or DVD player.

Note:

• If there is no audio output(only picture) or sound when your TV or DVD player is connected to the unit, please check the TV audio setting and try to set the audio output to other format.
• The , and button on both the unit and remote control do not work in this mode.

BLUETOOTH FUNCTION

1. Power on the unit as previously explained.
2. To switch to Bluetooth mode:
   • Press the MODE button on unit or remote control repeatedly;
   • Or press the BT button on remote control. When change to Bluetooth mode, the indicator in front of unit will blink in blue and a sound “Bluetooth” can be heard.
3. Power on the external Bluetooth device and activate Bluetooth mode to search for the unit.
4. When the Bluetooth name Hearth & Hand 06 appears, select it and make connection.
5. The sound “Bluetooth is paired” can be heard when connected successfully and the indicator will stay solid blue.
6. To disconnect the current connection, press and hold the BT button on remote control and “Bluetooth is disconnected” can be heard; press the BT button to reconnect the Bluetooth device.
   • Note: The unit will be automatically connected with the last connected Bluetooth device if both are activated Bluetooth function and in working range.
   • Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.

TROUBLESHOOTING

wall outlet.
The unit is in standby mode| Press  button on unit or remote control to power on it.
No sound or sound weak| Volume level in minimum position| Raise the volume level by pressing the VOL + Button on unit or remote control.
The paired/connected device is not in playback mode| Play music/movie in the paired/ connected device as usual and make sure the volume level of it is in high level.
Input source incorrect| Press the MODE button on unit or remote control to switch to right mode.
Sound distortion/ rattle| Volume level too high| ●Reduce the volume level by pressing the VOL- button on the unit or remote control.
●Reduce the volume level of the paired/connected device.
Remote Control not functioning| Out of range| Point the remote control to the remote sensor on the unit within 16 feet, +/-30 degrees.
The battery in the remote control is drained| Replace with new battery.
Bluetooth reception failure| The external device is too far from the unit|
Have not paired|
Have paired but no audio and Blue light keep flashing| ●Unmute the volume on Soundbar.

●Reconnect your BT device or restart the Soundbar.

SPECIFICATIONS

• Adapter input AC100-240V 50/60Hz
• Adapter output DC 22V 2A
• Bluetooth effective working range in open area minimum 33 feet
• Remote effective working range up to 16 feet
• Bluetooth version 5.4

ACCESSORIES

• 1x Instruction Manual
• 1x Power Adapter
• 1x Remote Control
• 1x AUX cable
• 2x AAA Carbon-zinc Batteries

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>