ITL Intelligence Lighting ITL-304D Remote Control Instruction Manual
- September 12, 2024
- ITL Intelligence Lighting
Table of Contents
ITL Intelligence Lighting ITL-304D Remote Control
Product Information
Specifications:
- Model: ITL-304D
- Function: Remote control for lights and fan
- Buttons:
- button: Turn light ON or OFF
- button: Adjust light brightness (press for more than 0.7 seconds)
- button: Turn fan ON or OFF
- button: Set fan speed to high
- button: Set fan speed to medium
- button: Set fan speed to low
Product Usage Instructions
Remote Control Operation:
- Press the 11 button to turn the light ON or OFF.
- Press the 22 button for more than 0.7 seconds to adjust the brightness of the light between maximum and minimum levels. The lights cycle every eight seconds.
- Use the 33 button to turn the fan ON or OFF.
- Press the 44, 55, or 66 button to set the fan speed to high, medium, or low respectively.
- The LED indicator will light up when any key on the remote control is pressed, indicating that the remote control is functioning.
Remote Control Pairing :
To pair the remote control with the device:
- Within 30 seconds after power is restored to the controller, press and hold the 3 key on the remote control transmitter for 5 seconds or until the light on the fan flashes.
- Test the light and fan functions using the remote transmitter to confirm that the learning process is complete.
Frequently Asked Questions (FAQ)
-
Q: How do I adjust the brightness of the light using the remote control?
A: Press and hold the 22 button for more than 0.7 seconds to start adjusting the brightness between maximum and minimum levels. -
Q: How can I set the fan speed to high?
A: Simply press the 44 button on the remote control to set the fan speed to high.
ITL‐304D Remote control operation instruction
As shown in the figure:
- button: to turn light ON or OFF.
- button: Press the button for more than 0.7 seconds to start adjusting the brightness of the light, cycling between maximum and minimum brightness. The lights cycle every eight seconds.
- button: to turn fan ON or OFF.
- button: to set the fan speed to high.
- button: to set the fan speed to medium.
- button: to set the fan speed to low.
- LED indicator: Press any key of the remote control, the indicator light will light up, and the remote control will issue instructions.
Remote control pairing
Within 30 seconds after power is restored to the controller, press and hold the “3” key on the remote control transmitter for 5 seconds or until the light on the fan flashes. Test the light and fan functions using the remote transmitter to confirm that the learning process is complete.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try correct the interference by one or more of
the following measures:
- Reorient the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>