KNIGHT LLC 0901231 Sani Select Instruction Manual
- September 12, 2024
- KNIGHT LLC
Table of Contents
KNIGHT LLC 0901231 Sani Select
Specifications
- Product Name: Knight Sani-Select
- Application: Dispensing system for various cleaning needs
- Capacity: Up to 16 different product concentrations
- Water Pressure: 30 to 80 PSI
- Water Temperature: Up to 140 degrees (F)
Installation
- Mount the unit to the wall using the provided screws and anchors.
- Select the appropriate metering tip and attach it to the barb fittings for the chemicals used.
- Install foot strainer on each supply tube, connect the tubes to the barbed fittings, and secure with a plastic tie wrap.
- Connect to a water supply using the provided garden hose adapter or hard plumbing directly to a water line.
- Attach the nozzle to the output hose and connect it to the unit.
Operation
- Turn the selector knob to Clean, Rinse, or Sanitize mode.
- Turn on the ball valve to activate the spray nozzle for dispensing the selected product and water mixture.
- To use the Foam feature, attach the Foam Wand to the quick-connect coupling on the nozzle and depress the spray handle.
Important Notes
- Use only the hose and spray nozzle supplied by Knight LLC.
- Do not adjust the knob on the spray nozzle from the full spray position.
- Install an appropriate backflow prevention device to prevent chemical backup into the water supply.
Troubleshooting
No Output
| Problem | Possible Cause | Remedy |
|---|---|---|
| Water supply is off | (1) Water supply is off | (1) Turn water supply on |
| Discharge hose is kinked | (2) Discharge hose is kinked | (2) Straighten hose or |
replace
FAQ
- Q: Can I adjust the dilution ratio of the chemicals?
- A: Yes, you can select from up to 16 different product concentrations using the provided metering tips.
- Q: What should I do if there is no product drawn from the container?
- A: Check for foot valve obstruction, clogged metering tip, blocked water inlet, low water pressure, no product in container, loose supply tube, or partially closed hose nozzle.
INTRODUCTION
The Knight Sani-Select is the perfect dispensing system for supermarket meat rooms, kitchen areas, bakeries, seafood stores, auto dealers, truck washing, loading docks, etc. The Knight Sani-Select is the economical system for controlling cleaning costs. Chemicals are mixed accurately and consistently at your chosen dilution ratio, utilizing a venturi valve. Up to 16 different product concentrations are available using the provided metering tips.
INSTALLATION
- Mount the unit to the wall using the screws and anchors provided. Dimensions are shown on page 2 for reference
- Select the appropriate metering tip (see chart in metering tip package) and screw into end of barb fittings for the chemicals used. The cover can be removed to access the barb fittings if necessary.
- Install foot strainer on the end of each supply tube. Slide a ceramic weight over each supply tube, then connect the tube onto the barbed fittings. Cinch a plastic tie wrap (provided) around the connection to secure. Insert foot end into container.
- Connect to a water supply using the provided 3/4″ garden hose adapter on the right side of the unit [Fig. 1a]. The adapter can be removed to permit hard plumbing directly to 3/8″ or 1/2″ NPT water line. Water pressure should be 30 to 80 PSI. Water temperature should not exceed 140 degrees (F).
- Attach the nozzle to the end of the output hose, then connect the hose to the fitting on the bottom of the unit [Fig. 1b].
OPERATION
- Turn the selector knob to the desired operation; Clean, Rinse, or Sanitize [Fig. 2a].
- Turn on the ball valve [Fig. 2b]. When the spray nozzle handle is activated, the selected product and water mixture will be dispensed.
- To use the Foam feature, attach the Foam Wand to the quick-connect coupling on the end of the nozzle (be sure air intake holes are not obstructed) and depress spray nozzle handle.
IMPORTANT NOTES
ONLY USE A HOSE AND SPRAY NOZZLE SUPPLIED BY KNIGHT LLC. DO NOT ADJUST THE KNOB ON THE SPRAY NOZZLE FROM THE FULL SPRAY POSITION. UNIT SUPPLIED WITHOUT A BACKFLOW PREVENTION DEVICE. TO PREVENT POSSIBLE CHEMICAL BACKUP INTO THE WATER SUPPLY, COMPLY WITH ALL LOCAL PLUMBING CODES AND INSTALL AN APPROPRIATE BACKFLOW PREVENTION DEVICE.
DIMENSIONS (IN) / PARTS TABLE
| Part No | Description | |
|---|---|---|
| 0700364 | Grommet, 1.375 ID, Nylon Black | |
| 0800226 | Fitting, Swivel, Nickle PLTD | Brass, 3/4 FGHT X 3/8 MNPT |
| 1202025 | Label, Sani-Select | |
| 1500445 | O-Ring, AS568-007, Aflas | |
| 1500449 | O-Ring, AS568-012, EPDM | |
| 1500496 | O-Ring, AS568-014, EPDM | |
| 1900607 | Screw, Pan Head, 18-8 SST | #6-32 X 1/2 |
| 1901104 | Screw, #8-32 x 3/8, 18-8 SST | Indented Slotted Hex Washer |
| 2300812 | Washer, Screen | (Water Input) |
| 5940008 | Selector, Insert | |
| 5940009 | Ring, Retaining, SST | |
| 5940010 | Venturi Body, 3 Position | |
| 5940011 | Gasket, Check Ball, EPDM | |
| 5940012 | Spring, Check | |
| 5940017 | Knob, Selector, Natural POM | |
| 5940019 | Fitting, Output | |
| 5940020 | Fitting, Input | |
| 5940023 | Fitting, Adapter, PP | 1/4 Barb to 5/8-18 UNF-2B |
| 5940025 | Ball, Check | |
| 5940029 | Fitting, Elbow 90 DEG. Brass | 3/8 NPT Male To Female |
| 7062002 | Base Plate | |
| 7561100 | Cover, Sani-Select | |
| 7561104 | Hanger, Hose | |
| 9603085 | Ball Valve, 3/8 NPTF, Brass | 1/4 Turn, T-handle |
| 7630008-1 | Clip, Rotary Dial 4 |
PARTS DIAGRAMS
TROUBLESHOOTING
| Problem | Possible Cause | Remedy |
|---|---|---|
| No output | (1) Water supply is off |
(2) Discharge hose is kinked
| (1) Turn water supply on
(2) Straighten hose or replace
Product is not drawn from container| (1) Foot valve obstruction
(2) Clogged metering tip
(3) Water inlet blocked
(4) Low water pressure
(5) No product in container
(6) Supply tube is loose
(7) Hose nozzle not fully open
| (1) Clean or replace
(2) Clean or replace
(3) Check/clean screen
(4) Must be 30 PSI minimum
(5) Re-fill or use new container
(6) Tighten or replace tie wrap
(7) Fully squeeze nozzle to open all
Too much, or too little product is drawn| Incorrect metering tip| Choose the
next closest ratio from chart and verify results — repeat this step as
necessary until the correct tip is chosen
No water (or very low flow)| (1) Obstruction at inlet screen area
(2) Low water pressure
(3) Scaled or clogged fittings
| (1) Clean obstruction/replace screen
(2) Use a more suitable source
(3) Clean scaling or free obstructions
Supply container fills with water| Check valve clogged| Clean or replace check valve
DISCLAIMER
Knight LLC does not accept responsibility for the mishandling, misuse or non- performance of the described items when used for purposes other than those specified in the instructions. For hazardous materials information consult label, MSDS, or Knight LLC.
WARRANTY
For complete product terms and conditions scan the QR code at right or enter the following URL into your browser: http://cfstech.info/t-and-c
KNIGHT LLC is part of the CFS Technologies family of brands. www.knightequip.com | cfstech.com 8504 MacArthur Dr., North Little Rock, AR 72118 USA • 501-895-2820 | 800-999-2820 General: sales@cfstech.com | Tech. Assist.: techsupport@cfstech.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>