CHEMI-CON NPCAPTM Series Aluminum Electrolytic Capacitors Owner’s Manual

CHEMI-CON NPCAPTM Series Aluminum Electrolytic Capacitors

Specifications

• Temperature Range: -55 to +105°C
• Rated Voltage Range: 2.5 to 6.3Vdc
• Capacitance Tolerance: *Note
• Leakage Current: 0.10 max. (at 20, 120Hz)
• Dissipation Factor (tan δ): Low Temperature Characteristics (Max.Impedance Ratio)
• Endurance: 20,000 hours at 105°C
• Bias Humidity Test: Z(-25)/Z(+20) 1.15, Z(-55)/Z(+20) 1.25 (at 100kHz)

Product Usage Instructions

Precautions and Guidelines
This product is solvent resistant type. Please refer to the guidelines provided before usage.

• Appearance and Performance Criteria
  Ensure that appearance, capacitance change, D.F., ESR, and leakage current meet specified values after testing under various conditions.

• Voltage Treatment
  It is recommended to measure leakage current after applying DC rated voltage for 120 minutes at 105°C if any doubt arises.

• Dimensions
  Refer to the provided dimensions for terminal codes and markings on the product.

• Marking
  Each product is marked with specific code details for identification purposes.

FAQ

• What is the endurance rating of the capacitors?
  The capacitors have an endurance rating of 20,000 hours at 105°C.

• Are the capacitors RoHS2 Compliant?
  Yes, the capacitors are RoHS2 Compliant and Halogen Free.

• What is the surge voltage test procedure for the capacitors?
  The capacitors are subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105V for 30 seconds through a protective resistor and discharge for 5 minutes 30 seconds.

FEATURES

• Super low ESR, high ripple current capability
• Endurance: 20,000 hours at 105℃
• Rated voltage range : 2.5 to 6.3Vdc
• Solvent-resistant type (see PRECAUTIONS AND GUIDELINES)
• RoHS2 Compliant
• Halogen Free

SPECIFICATIONS

Leakage Current

*Note

| I=0.2CV or 500µA, whichever is greater

Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)

|

(at 20℃ after 2 minutes)

Dissipation Factor

(tan δ )

| 0.10 max.| (at 20℃, 120Hz)
Low Temperature Characteristics (Max.Impedance Ratio)| Z(-25℃)/Z(+20℃)≦1.15 Z(-55℃)/Z(+20℃)≦1.25|

(at 100kHz)

Endurance| The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 20,000 hours

at 105℃.

Appearance| No significant damage|
Capacitance change| ≦±20% of the initial value
D.F. (tanδ)| ≦150% of the initial specified value
ESR| ≦200% of the initial specified value
Leakage current| ≦The initial specified value
Bias Humidity Test| The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to DC voltage at 60℃,

90 to 95% RH for 1,000 hours.

Appearance| No significant damage|
Capacitance change| ≦±20% of the initial value
D.F. (tanδ)| ≦The initial specified value
ESR| ≦The initial specified value
Leakage current| ≦The initial specified value
Surge Voltage Test| The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds

through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.

Rated voltage (Vdc)| 2.5| 4.0| 6.3|
Surge voltage (Vdc)| 2.9| 4.6| 7.2

Appearance| No significant damage|
Capacitance change| ≦±20% of the initial value
D.F. (tanδ)| ≦The initial specified value
ESR| ≦The initial specified value
Leakage current| ≦The initial specified value

Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.

DIMENSIONS

Terminal Code: E

MARKING

PART NUMBERING SYSTEM

Please refer to “Product code guide (conductive polymer type)”

STANDARD RATINGS

WV

(V dc )

| Cap (µF)| Case size

φ D × L(mm)

| ESR

(m Ω max./20 ℃ , 100k to 300kHz)

| Rated ripple current (mArms/105 ℃ , 100kHz)| ****

Part No.

---|---|---|---|---|---
2.5| 820| 6.3 ×8| 7| 5,000| APSE2R5E□□821MF08S
4| 560| 6.3 ×8| 7| 5,000| APSE4R0E□□561MF08S
6.3| 470| 6.3 ×8| 8| 4,700| APSE6R3E□□471MF08S
560| 6.3 ×8| 8| 4,700| APSE6R3E□□561MF08S

Enter the appropriate lead forming or taping code.

RATED RIPPLE CURRENT MULTIPLIERS

Frequency Multipliers

Frequency （ Hz ）| 120| 1k| 10k| 50k| 100k to 500k
---|---|---|---|---|---
Radial lead type| 0.10| 0.35| 0.60| 0.80| 1.00

• Always read “Notes on Use” before using the product in order to enable you to use the product correctly and prevent any faults and accidents from occurring.
• Request the Product Specification on the product of NIPPON CHEMI-CON CORPORATION to refer to it as well as this brochure prior to the order of the products. Some specific notes on use of the ordered product may be described in the specifications.
• The products listed in this catalog are designed and manufactured for general electronics equipment use and are not intended for use in applications that can adversely affect human life; where the malfunction of equipment may cause damage to life orproperty. In addition, our products are not intended to be used in specific applications that may cause a major social impact. Please consult with us in advance of usage of our products in the following listed applications. ① Aerospace equipment ② Power generation equipment such as thermal, nuclear, etc. ③ Medical equipment ④ Transport equipment (automobiles, trains, ships, etc.) ⑤ Transportation control equipment ⑥ Disaster prevention/crime prevention equipment ⑦ Highly publicizedV information processing equipment ⑧ Submarine equipment ⑨ Other applications that are not considered general-purpose applications.
• The circuits described as examples in this catalog and the “delivery specifications” are featured to show the operations and usage of our products, however, this fact does not guarantee that the circuits are available to function in your equipment systems. We are not in any case responsible for any failures or damage caused by the use of the information contained herein. You should examine our products, of which the characteristics are described in the “delivery specifications” and other documents, and determine whether or not our products suit your requirements according to the specifications of your equipment systems. Therefore, you bear final responsibility regarding the use of our products. Please ensure that you take appropriate safety measures such as using redundant design and malfunction prevention measures to prevent fatal accidents and/or fires in case any of our products malfunction.
• We strongly recommend our customers to purchase Nippon Chemi-Con products only through our official sales channels. We assume no responsibility for any defects or damages caused by using products purchased from outside our official sales channel or of counterfeit goods. In addition, we will ask the customer to pay the investigation cost for products purchased outside our official sales channel.
• We reserve the right to discontinue production and delivery of products. We do not guarantee that all the products included in this catalog will be available in the future. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products
• We continually strive to improve the quality and reliability of our products, but in any case that our product does not meet our published specifications, please stop using it promptly and contact us immediately. As for compensation for non-conforming goods delivered by Chemi-Con, we will limit it only to goods found in non-compliance of our published specifications. This may be accomplished by a no cost replacement of non-conforming individual products, a credit of the piece price paid per each individual non-conforming product, or in other ways deemed necessary. In addition, we have an established system with enhanced traceability, therefore we will limit the applicable lot items for any potential compensation.

Part Numbering System
Part Numbering System (Appendix)
Standardization
Available Items by Manufacturing Locations
Environmental Measures
Technical Note
Precautions and Guidelines
Recommended Soldering Conditions
Taping, Lead-preforming, Terminal and Packaging Options

Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>