SIERZEGA SR7 Traffic Radar User Guide
- September 9, 2024
- SIERZEGA
Table of Contents
SIERZEGA SR7 Traffic Radar
Specifications :
- Product: Traffic Radar SR7
- Mounting Distance: 1 to 4 meters from the edge of the road
- Mounting Height: 0.8 to 1.2 meters
- Power Supply: Battery-operated
- Connectivity: LTE modem and GPS
Product Usage Instructions
-
Mounting:
The SR7 should be mounted on the roadside at a distance of 1 to 4 meters from the edge of the road. The mounting height of the upper edge of the box must be 0.8 to 1.2 meters for reliable vehicle axle detection. Use the enclosed clamps to attach the device to masts/pipes following separate instructions. -
Alignment:
Ensure proper alignment during mounting to achieve accurate readings. -
Power Supply:
Insert the battery into the housing with contacts facing front right. Push the battery to the rear left and then slide it into the housing on the right side. Connect the battery cable, ensuring it is not near the lock. Close and lock the door securely. -
Checking Status:
The SR7 is equipped with an LTE modem and GPS. Data on battery status, current position, reception, and temperature are transmitted to servers every hour. Monitor the status at sr7.sierzega.com using the device’s serial number and PIN.
FAQ :
-
Q: How can I obtain a copy of the declaration of conformity for the product?
A: You can contact Sierzega Elektronik GmbH at their provided contact information. -
Q: What should I do when the product reaches the end of its useful life?
A: Dispose of it according to local laws and regulations. Contact your local waste disposal authority for information on designated collection points. -
Q: How far should the device be installed from the body for FCC radiation compliance?
A: The device should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
Traffic radar SR7
Quick Start Guide
Read this first
Read through this Installation Guide carefully before installing the product.
Keep the Installation Guide for future reference.
Liability
Every care has been taken in the preparation of this document. Please inform
Sierzega of any inaccuracies or omissions. Sierzega Elektronik GmbH cannot be
held responsible for any technical or typographical errors and reserves the
right to make changes to the product and manuals without prior notice.
Sierzega Elektronik GmbH makes no warranty of any kind with regard to the
material contained within this document, including, but not limited to, the
implied warranties of merchantability and fitness for a particular purpose.
Sierzega Elektronik GmbH shall not be liable nor responsible for incidental or
consequential damages in connection with the furnishing, performance or use of
this material. This product is only to be used for its intended purpose.
Equipment modifications
This equipment must be installed and used in strict accordance with the
instructions given in the user documentation. This equipment contains no user-
serviceable components. Unauthorized equipment changes or modifications will
invalidate all applicable regulatory certifications and approvals.
Regulatory information
Europe
This product complies with the applicable CE marking directives and harmonized
standards.
A copy of the declaration of conformity may be obtained from Sierzega
Elektronik GmbH.
USA / Canada
This device contains FCC-ID S6P-SR7 / IC 5792A-SR7 which includes FCC-ID
QOQ-GM220P / IC 5123A-GM220P and FCC-ID XMR201910BG95M3 / IC 10224A-2019BG95M3
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.
Statement Regarding FCC / IC Compliance
( CAN ICES-3 (B)/NMB-3(B))
This device complies with Part 15 of the FCC Rules / Innovation, Science and
Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Disposal and recycling
When this product has reached the end of its useful life, dispose of it
according to local laws and regulations. For information about your nearest
designated collection point, contact your local authority responsible for
waste disposal. In accordance with local legislation, penalties may be
applicable for incorrect disposal of this waste.
Europe
- This symbol means that the product shall not be disposed of together with household or commercial waste. Directive 2012/19/EU on waste electrical and electronic equipment (WEEE) is applicable in the European Union member states. To prevent potential harm to human health and the environment, the product must be disposed of in an approved and environmentally safe recycling process. For information about your nearest designated collection point, contact your local authority responsible for waste disposal. Businesses should contact the product supplier for information about how to dispose of this product correctly.
- This product complies with the requirements of Directive 2011/65/EU and 2015/863 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS).
Contact Information
Sierzega Elektronik GmbH Valentinstraße 11 4062 Thening Austria
Tel: +43 (7221) 64114-0 Web: www.sierzega.com
Version 08/2024
MOUNTING
- The SR7 is mounted on the roadside at a distance of 1 to 4 metres from the edge of the road.
- The moun ng height of the upper edge of the box must be 0.8 to 1.2 metres for reliable vehicle axle detec on.
- The device is a ached to masts/pipes using the enclosed clamps (see separate instructions).
Alignment
- The rear of the SR7 must be mounted at a 90° angle to the road.
- Automatic calibration – The MIMO radar of the SR7 also looks to the side using several antennas and simultaneously detects the vehicles at different angles. This enables the SR7 to automatically determine the actual exact mounting angle and consider the results for further measurements and calculations.
Power supply
- Place the battery in the housing as shown. Contacts to the front right. Push the battery to the rear le? and then slide it into the housing on the right side.
- Then connect the battery cable and ensure that the cable is not near the lock.
- Close and lock the door. All screws on the outside of the housing are the?-resistant and cannot be opened from the outside.
Check Status
- The SR7 is equipped with an LTE modem and GPS. Data on the current battery status, current posi on, reception and temperature in the device is transmitted to our servers every hour.
- The status can be monitored at any me at sr7.sierzega.com using the device’s serial number and PIN.
Download data
- It is also possible to download data at sr7.sierzega.com. To do this, select the “Traffic Data” tab at the bo om right and initiate the start of a data download.
- SR7 checks requests every hour and then carries out the upload to the server if required. Files remain stored on the server until they are manually deleted from there. The data is automatically deleted in the device after it is uploaded to the server.
Create reports
- The latest SRA evaluation software is available for use at www.sierzega.com.
- The offline version SRA 5.4 can be found under “Software – Downloads”, and an online version of the SRA software will also be available shortly, which will significantly simplify evaluation and add new features enabled by the SR7.
SR7 Quick Start
Guide, Version 1, 12/2023