BOSCH 9001703330 Ceran Hob Instruction Manual
- September 9, 2024
- Bosch
Table of Contents
BOSCH 9001703330 Ceran Hob
Specifications
- Model Number : 9001703330
- Date of Manufacture : 040627
General information
- Read this instruction manual carefully.
- Only a licensed expert may connect the appliance.
- Improper installation, or opening of the appliance, connection, or assembly may lead to a loss of validity of the product warranty.
- Switch off the power supply before carrying out any work.
- After installation, ensure that the user does not have access to the electrical components.
- Never use this appliance in boats or vehicles.
Safe installation
Follow these safety instructions when installing the appliance.
The appliance can only be used safely if it is correctly installed by the
installation instructions. The installer is responsible for ensuring that the
appliance works perfectly at its installation location.
WARNING ‒ Danger: Magnetism! The appliance contains permanent magnets. They may affect electronic implants, e.g. pacemakers or insulin pumps.
- Persons with electronic implants must stand at least 10 cm away from the appliance.
WARNING ‒ Risk of injury
Parts that are accessible during installation may have sharp edges and may
lead to cutting injuries.
- Wear protective gloves.
Chemicals may be dangerous. When handling chemicals, you must observe the recommendations of the chemical producers.
- Wear personal protective equipment.
Instructions for the electrical connection
To safely connect the appliance to the electrical system, observe the
following instructions.
- Only an authorized expert or a specially trained service technician may connect the appliance. The person must be approved by the local regulations of the country and the electricity supply company.
- Connect the appliance to a fixed installation and set up appropriate isolating switches by the installation regulations.
- The manufacturer shall assume no liability for malfunctions or damage resulting from incorrect electrical wiring.
Connection type
The appliance corresponds to protection class 1. You should therefore only
use the appliance with a protective earth connection.
Information on fitted units
- You can only install the induction hob above drawers or ovens with fan ventilation. Do not install refrigerators, dishwashers, non-ventilated ovens, or washing machines below the hob.
- Ensure that the fitted unit is heat-resistant up to at least 90 °C.
Worktop
Follow the worktop manufacturer’s recommendations.
- Level, horizontal, stable.
- The worktop into which you are fitting the appliance must be able to withstand loads of approx. 60 kg.
- For thin worktops, use heat-resistant and moisture-resistant reinforcement material.
- Only check the evenness of the hob after it has been installed.
Extractor hood
The clearance between the extractor hood and the hob must correspond at least
to the clearance specified in the installation instructions for the extractor
hood.
Preparing the fitted units
- Mark the unit cut-out by the installation diagram.
- Ensure that the angle of the cut surface to the worktop is 90°. → Fig. 1
- Ensure that the angle of the cut surface to the worktop is 90°. → Fig. 1
- After making the cut-outs, remove any shavings.
- Seal the cut surfaces with heat-resistant material.
Ventilation
To guarantee that the appliance works correctly, the hob must be sufficiently
ventilated. The ventilation in the lower section of the appliance requires a
sufficient supply of fresh air. Therefore, if required, adjust the units for
this purpose.
- Maintain a minimum clearance between the rear of the unit and the kitchen wall. → Fig. 2
- Ensure that an opening at the top of the rear of the unit is unobstructed. → Fig. 3
- If the clearance from the back wall of the unit is less than 20 mm, create an opening on the underside. → Fig. 4
- Do not hermetically seal the lower base.
Note: If the appliance is installed in an island unit or in another location that is not described here, guarantee that the hob is ventilated appropriately.
Installation above a drawer
- To guarantee good ventilation, the clearance between the surface of the worktop and the upper area of the drawer must be 65 mm. → Fig. 5
Installation above an oven
- To ensure good ventilation, the clearance between the top of the worktop and the surface of the oven front must be 30 mm and the minimum clearance between the oven and hob must be 5 mm.
- If the clearance between the hob and the oven needs to be increased, refer to the installation instructions for the oven. → Fig. 6
Inserting the hob
- Adjust the hob in the front section of the built-in niche.
- Insert the hob in the cut-out.
- Place the appliance into the cut-out in the worktop.
- Screw the enclosed retaining clips onto the worktop and carefully onto the appliance.
- Do not use an electric screwdriver. → Fig. 7
- Seal the tile joints on tiled work surfaces with silicone rubber.
Note: Do not kink or trap the connection cable, and keep it away from sharp edges and hot parts.
Connecting the appliance
Requirement: Observe the connection data on the rating plate.
- Only connect as shown in the circuit diagram: → Fig. 8
- BN: Brown
- BU: Blue
- GN/YE: Green and yellow
- Check that the appliance is ready for operation: If, or appears on the appliance’s display, the appliance is not connected correctly. Disconnect the appliance from the power supply and check the power cord connection at the mmainsupply.
Special combinations
If you install the hob above an oven made by another brand, use a wooden
partition floor. → Fig. 9
Removing the appliance
ATTENTION!
Tools may damage the appliance.
- Never prise out the appliance from above.
- Disconnect the appliance from the main power supply.
- If there are any fastening brackets, remove them.
- Push out the hob from below.
Frequently Asked Questions
- Q: What should I do if I have an electronic implant?
- A: Individuals with electronic implants must maintain a distance of at least 10 cm from the appliance due to the presence of permanent magnets.
- Q: How should I ensure proper ventilation for the appliance?
- A: Follow the ventilation guidelines provided in the installation instructions, including maintaining clearances and openings for adequate airflow.