Lowes 6030 Wall Mount and Post Mount Fixture Installation Guide

Lowes 6030 Wall Mount and Post Mount Fixture

Product Usage Instructions

Wall Mount Installation (Fig. 1 & 2)

1. Mounting Preparation:
   

   • A) Place the #8-32 HEX NUT onto the #8-32 FIXTURE MOUNTING SCREW and attach it to the MOUNTING RACKET or universal mounting plate.

   • B) If using a single 1/8IPS NIPPLE for mounting, thread the 1/8IPS HEX NUT onto the NIPPLE and screw it into the MOUNTING BRACKET.

2. Wiring Setup: Pull the power supply wires out from the OUTLET BOX and connect them to the respective fixture lead wires using wire connectors. Connect the ground wires together.

Post Mount Installation (Fig. 3)

1. Mounting Preparation:
   Place the fixture on top of the POST and mark hole positions on the POST using the holes on the POST CAP. Drill holes at marked positions.

2. Wiring Setup:
   Pull out power supply and fixture lead wires, connect them by color, and connect ground wires using appropriate wire connectors.

IMPORTANT INSTRUCTION

PLEASE READ CAREFULLY AND SAVE THESE INSTRUCTIONS, AS YOU MAY NEED THEM AT ALATER DATE.

CAUTION – Turn off the main power at the circuit breaker before installing the
Fixture, in order to prevent possible shock.
Remove the fixture and the mounting package from the box and make sure
That no parts are missing by referencing the illustrations on the installation Instructions.

INSTALLATION INSTRUCTIONS

FOR WALL MOUNT ( Fig. 1 & 2 )

1. A) Place the #8-32 HEX NUT(5) onto the #8-32 FXTURE MOUNTING SCREW(7). And attach the FIXTURE MOUNTING SCREW (7) to the MOUNTING RACKET(4).or universal mounting plate (whichever is provided). Do not tighten the HEX NUTS at this time.(Fig.1)
   B) If the fixture uses a single 1/8”IPS NIPPLE(7) for mounting, thread the /8”IPS HEX NUT(5) onto the NIPPLE (7), and screw the NIPPLE(7) into the MOUNTING BRACKET(4).without tightening the HEX NUT(5).(Fig.2)

2. Pull the power supply wires out from the OUTLET BOX (3) and mount the MOUNTING BRACKET (4) or the universal mounting plate to the OUTLET BOX(3), using MOUNTING SCREWS(6).

3. Attach the SUPPLY BLACK WIRE (10) to the BLACK FIXTURE LEAD WIRE (11) by using the WIRE CONNECTOR (12). In the same manner, attach the SUPPLY WHITE WIRE (8) to the WHITE FIXTURE LEAD WIRE (9). Connect the POWER SUPPLY GROUND WIRE (13) to the FIXTURE GROUND WIRE (14) using a WIRE CONNECTOR (12) (not included).

4. Place the CANOPY(15) on the fixture over the OUTLET BOX(3) and onto the fixture mounting screws﹝ or NIPPLE (7).﹞,and adjust the #8-32 fixture mounting screws (or NIPPLY) until they protrude out from the CANOY(15) 1/4”. Remove the CANOPY(15) and secure the position of the fixture mounting screw ( or NIPPLE) by tightening the HEX NUT(S)(5) against the MOUNTING RACKET(4). Place the CANOPY(15) back onto the fixture mounting screws,(or NIPPLE), and secure into place using the DECORATIVE NUT(16) provided.

5. Screw the TAIL SECTION (18) (if provided) onto the COUPLING (19) located at the bottom of the lamp compartment.

6. Screw a light bulb that does not exceed the maximum wattage specified on the fixture label, into socket located inside the lamp compartment. Place the lamp cover onto the top of the lamp compartment, and secure in position using the decorative head screws provided.

FOR POST MOUNT(Fig.3)

1. Place the fixture on the top of the POST (9) on which the fixture is to be mounted and position as desired. Using the holes located on the POST CAP (3) mark the hole position on the POST (9). Remove the fixture from the POST (9) and drill a 1/8” diameter hole at each marked position on the POST (9).
2. Pull the power supply wires out from the POST (9) and the fixture lead wires out from the POST CAP (3), and attach the wires together by connecting BLACK to BLACK (6) and WHITE to WHITE (5). Attach the POWER SUPPLY GROUND WIRE (7) to the FIXTURE GROUND WIRE (8) using a wire connector rated for the size of wire being connected.
3. Place the connected wires down inside the POST (9), and mount the POST CAP (3) in place, aligning the holes in the POST CAP (3) with the ones on the POST (9). Secure the POST CAP (3) to the POST (9) using #10×1/2” long self-tapping SHEET METAL SCREWS (4) provided.
4. Screw a light bulb that dose not exceed the maximum wattage specified on the fixture label, into the lamp socket. Place the LAMP COVER (1) onto the top of the lamp compartment, and secure in position using the DECORATIVER HEAD SCREWS (2) provided.

FAQs

• Q: What is the maximum wattage for the light bulb that can be used with this fixture?
  A: The maximum wattage is specified on the fixture label. Do not exceed this wattage to avoid damage.

• Q: Are wire connectors included in the package?
  A: Wire connectors for connecting wires are not included. Please ensure you have suitable connectors before installation.

• Q: Can this fixture be used in outdoor settings?
  A: This fixture is suitable for outdoor use but ensure it is installed following proper weatherproofing guidelines.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>