Meatmeet ME-TEMP01 Thermometer User Manual

September 7, 2024
Meatmeet

Meatmeet ME-TEMP01 Thermometer

Product Specifications

  • Probe: Only support BLE 1M
  • Booster: Only support BLE 1M
  • Other Parameters:
    • Used for indoor and outdoor environment
    • Altitude: Up to 2000m Overvoltage Category II
    • Pollution Degree of Intended Environment: Pollution Degree

Product Usage Instructions

  1. Step 1: Scan the QR code above or search for Meatmeet on the App Store for iOS devices or on the Google Play Store for Android devices. Download and install the Meatmeet APP.
  2. Step 2: Enable Bluetooth and Wi-Fi on your smart device.
  3. Step 3: Fully charge the booster and probe. Connect the provided USB charging cable to any USB charger to charge the booster. LED2 will light with solid blue once it is fully charged.
  4. Step 4: Pair the booster to your smart device. Press the power button 2s to activate the booster. Launch the Meatmeet APP and press Add device. Select booster and follow the instructions to pair your device.
  5. Step 5: Start cooking. Insert your probe into the meat deeply enough to ensure the safety notch on the probe is fully covered by the meat. Set the meat type and doneness you desire or your expected meat temperature within the Meatmeet APP.

Caution

  • Please insert the probe deeply enough into the meat to avoid damage.
  • To ensure uninterrupted connectivity, keep the booster as close as possible to the probe (within 9 ft/3 m).
  • DO NOT use the probe in a microwave or pressure cooker.
  • The probe will be very hot after each use. DO NOT touch it with your bare hands.
  • DO NOT submerge the probe in water for long periods.
  • DO NOT run the probe under cold water immediately after cooking. Let the probe cool down before washing.
  • Soap and hot water should be enough to clean the probe. Do not use scouring pads or harsh cleansers, which can scratch the probe.
  • Please pay attention to waterproof protection if a booster is used in the open environment.
  • The booster could be charged horizontally or vertically, and when placed vertically, it should be on a level surface with no inclination.

Compliance

  • Probe: Model: short probe: ME-TEMP01; long probe: ME-TEMP02 FCCID: 2AYOTME-TEMP01 IC: 26903-METEMP01
  • Booster Model: ME-BOX01 FCCID: 2AYOTME-BOX01 IC: 26903-MEBOX01
  • FCC Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference.

Introduction

  • Thank you for purchasing a wireless smart meat thermometer: Meatmeet Pro. With a better cooking experience, please scan the following QR code to download and install the Meatmeet APP, with which you could be able to remotely monitor the meat temperature and ambient temperature in the process of cooking. Additionally, you could also know how much time is left for the food to be done.

iOS APP QR code

Android APP QR CODE

What’s in the box

  • Booster x1
  • Probe x1
  • Type-C cable x1
  • User manual x1

Product Appearance

Button

LED

Product specifications

Probe

Booster

Other parameters for both probe and booster are listed as below:

  • a. Used for indoor and outdoor environment
  • b. Altitude: Up to 2000m
  • c. Overvoltage Category II
  • d. Pollution Degree of Intended Environment: Pollution Degree 2

Usage instructions

Please follow the steps below to set up your Meatmeet Pro.

  • Step 1: Scan the QR code above or search for “Meatmeet” on the APP store for ios devices or on the Google Play store for Android devices. Download and install the Meatmeet APP.
  • Step 2 : Enable Bluetooth and WiFi on your smart device.
  • Step 3: Fully charge the booster and probe. Connect the provided USB charging cable to any USB charger to charge the booster. LED2 will light with solid blue once it is fully charged.
  • Step 4: Pair the booster to your smart device
    • Press the power button 2s to activate the booster.
    • Launch the Meatmeet APP and press Add device. Select booster and follow the instructions to pair your device. Once successfully paired, LED1 will light with solid blue.
    • If you want to clear the pair info and re-pair with another network, press the power button for more than 5s until LED1 fast blinks with blue color, then repeat the above step until the booster is fully paired
  • Step 5: Start cooking
    • Insert your probe into the meat deeply enough to make sure the safety notch on the probe is fully covered by the meat.
    • Set the meat type and doneness you desire or your expected meat temperature within the Meatmeet APP.
    • Once the realtime temperature reaches your expected target temperature, an alarm will sound from the smart device and booster. Within the APP, you can set the notification from a smart device with sound, message or vibration.

Caution

  • The stainless steel probe withstands up to 212°F/100°C and the ceramic handle withstands up to 572°F/300°C. Exceeding the recommended temperatures may damage the probe.
  • Please insert the probe deeply enough into the meat to make sure the safety notch on the probe is fully covered by the meat. This could avoid extremely high heat damaging electronics.
  • To ensure uninterrupted connectivity, we recommend the booster to be as close as possible to the probe(within 9ft/3m).
  • DO NOT use the probe in a microwave or pressure cooker.
  • The probe will be very hot after each use. DO NOT touch it with your bare hands.
  • DO NOT submerge the probe in water for long periods of time.
  • DO NOT run the Probe under cold water immediately after cooking. Let the probe cool down prior to washing.
  • Soap and hot water should be enough to clean the probe. Do not use scouring pads or harsh cleansers, which can also scratch the probe.
  • Please pay attention to waterproof protection if a brooster is used in the open environment.
  • The booster could be charged horizontally or vertically, and when placed vertically, it should be on a level surface with no inclination.

Compliance

Probe

  • Model: s hort probe: ME-TEMP01; long probe: ME-TEMP02
  • FCC ID: 2AYOTME-TEMP01
  • IC: 26903-METEMP01

Booster

  • Model: ME-BOX01
  • FCC ID: 2AYOTME-BOX01
  • IC: 26903-MEBOX01

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference
  2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and uses radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

CAUTION: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Radiation Exposure Statement

  • This probe and booster comply with FCC radiation exposure limits set forth for an uncontrolled environment.
  • This booster should be installed and operated with a minimum distance of 20cm between the radiator& your body.

IC statement
This device complies with the Innovation, Science, and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

  1. this device may not cause interference, and
  2. this device must accept any interference, including interference that may cause undesired operation of the device.

The probe and booster comply with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance.
The minimum distance from the body to use the booster is 20cm.

EU Declaration of Conformity
Hereby, the manufacturer declares that this product meets the basic requirements and applicable regulations of the Radio Equipment Directive 2014/53/EU, and the EMC Directive 2014/30/EU. The complete declaration of conformity can be found at: www.meatmeet.net.

Disposal of the Electronic Appliance

This electronic appliance should not be disposed of with normal household waste. Dispose of the unit at an approved facility or at your local recycling center. Please observe the current rules and regulations when disposing of the appliance. Contact your local council if in doubt.

Frequently Asked Questions

  • Q: Is it safe to wash the probe after each use?
    • A: Yes, it is safe to wash the probe after each use with soap and hot water. Just make sure not to submerge it for long periods and let it cool down before washing.
  • Q: Can I use the probe in a microwave?
    • A: No, do not use the probe in a microwave or pressure cooker as it may damage the electronics.
  • Q: How close should the booster be to the probe for uninterrupted connectivity?
    • A: It is recommended to keep the booster as close as possible to the probe, within 9ft/3m, for uninterrupted connectivity.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals