Luxton Home CT-7409-RC Premium Foam Massage Table Instruction Manual
- June 17, 2024
- Luxton Home
Table of Contents
Luxton Home CT-7409-RC Premium Foam Massage Table
INSTRUCTION MANUAL
Premium Foam Massage Table
(CT-7409-R C)
Specifications:
- Model: CT-7409-RC
- Max Working Load: 250 kgs
- Features: Handle, Copper Button, End Plate, Rubber Foot, Cable, Headrest, Side Armrests, Face Hole, Outlet, Hanged Armrest Pad
Precautionary Instructions
1. Maintain the table periodically. Make sure all screws are secure and the
cable has not deteriorated or frayed. Make sure there is no cracks on the
wooden structure.
2. Do not overload the table beyond the recommended weight limit. This could
result in serious injury to the user. This product is tested to hold a max
working load of 250 kgs.
3. Do not use alcohol-based cleaners when cleaning the vinyl. This could
cause damage to the vinyl material. Use warm soapy water and wipe dry.
4. Make sure when using the table that all four legs are at the same level.
Using the legs at different levels can cause the table to be unstable and
cause injury.
5. Do not allow children to assemble or disassemble the massage table for you
unless under supervision.
6. Be careful when using sharp objects as they can pierce the covering. Keep
the table’s covering away from being contacted by the sharp items.
Setting Up Your Table
Steps are as below:
1. Release the buckle.
2. Lay the table on its side with four rubber feet on the floor, open up the
table with four legs extended as full as possible.
3. Take out all accessories.
4. Lift the table up until all legs are on the floor.
5. Put accessories into the corresponding outlets, put on the hanged armrest
or sling on the headrest cradle.
6. Release the side handle and press it in once the headrest is adjusted to
the required position.
7. Now the table is ready for your use.
Re: The height of table is adjustable by turning off the knobs on the leg and take out the movable leg to adjust the height by choosing the holes on the movable leg, put back onto the leg and fasten the knobs firmly. Four legs should be done in the same way one by one and make sure all legs are adjusted into same height level.
Instructions for Installing Wheels of Carry Bag
Parts Included:
a. 2 pcs of universal wheels
b. 2 pcs of directional wheels
c. 9 pcs of screws
d. 1 pc of wrench
Assemble all wheels on the bottom of the carry bag. Both Universal wheels should be installed on the same side of the carry bag that has the handle.
To install wheels, place the wheels on the bottom of the carry bag and align
the screw with the hole in the bottom of the carry bag. Tighten the screw with
a wrench.
Note: Each wheel is to be tightened with two screws.
Note: Avoid using the wheeled carry bag on roads with tough conditions or uneven surfaces.
Fold Up and Carry Along
1. Take out all accessories.
2. Lay the table on its side with four rubber feet on the ground.
3. Put all accessories under the elastic strap under the top veneer.
4. Fold the legs on each end at angle towards inside by pressing the
corresponding support beams.
5. Fold the table up and lock the buckle.
6. Put table inside the carry bag and zipper up. Carry the table with carry
bag with shoulder belt.
Warning: If the frame/legs/table structure is damaged in anyway, then you should not use this table. Using this table when damaged may cause harm or serious injury to you or your patient. You should seek repair immediately.
Fold Up and Carry Along:
No specific instructions provided in the manual.
FAQ (Frequently Asked Questions)
Q: What is the weight limit of the massage table?
A: The table is tested to hold a max working load of 250 kgs.
Q: Can children assemble or disassemble the table?
A: Children should not assemble or disassemble the table without supervision.