HayBoss 700A,700UHD Moisture Sensor Kit For Large Square Balers Installation Guide

Model 700A & 700UHD
Moisture Sensor Kit for Large Square Balers
Installation Manual
700A & 700UHD-24-INST-Imp&Metric
2/24

Introduction

Thank you for purchasing a Harvest Tec moisture monitor system. This moisture monitoring system has been designed to be operated through a number of different displays and tablets using the Precision Baling App.
These include, the Harvest Tec display, the baler’s ISOBUS and display on the baler monitor, or iOS/Android Tablet (not included).
The 700 Series Moisture System is designed to show moisture through the balers ISOBUS. Failure to follow instructions can result in personal injury or equipment malfunction. If you need parts for the system, please view the Parts Breakdown toward the back of this manual and contact your local authorized dealer to order the parts.

**System Requirements

**

The Baler Processor must have Version 3.3 or higher.
C1000 monitor must have Version 3.0.1 or higher
If equipped with the SBM, the SBM must have Version 4.0 or higher .
Made for Harvest Tec Display, Baler Integration, or Tablet
For best performance ensure all displays are running the latest operating system

Tools Needed

Standard Wrench set Electric drill and bits Side cutter
Standard Socket Set
Hammer
Center punch

Installation of the Processor (IPM) on standard balers

Follow the instructions below to mount the Main Processor (IPM) onto your baler. The locations shown are on the right twine box (looking form the back of the baler). Mark and drill the two 3/8 (10mm) holes and install the (IPM) with two 5/16 x 1 bolts, four 1/4” washers, and two 5/16” nylock nuts. Main harness whip coming out of (IPM) should point to the ground. When attaching other harness make sure to loop them below the (IPM) so as not to funnel water into the control.

Main Wire Harness and Baler Interface Harness Routing and Connections

UHD Baler ISOBUS Integration Connection
Beneath the right rear chamber locate the harness labeled (LHR-C72 ISOBUS Term). It is located at the right rear corner of the baler frame. Attach Baler Interface Harness (006-765VA) to that location
Installation of the Star Wheels – Non-UHD Balers
Locate parts bag E and mount star wheels on top of the baler, just behind the knotters and under the walkway on both sides. The notch and holes for the star wheel are precut, secure the star wheels with 5/16” x 3” BHCS (x2 each side) from the bottom. Blocks are dropped down on the bolts and secured in place with the star wheel twine guards (001-4645, 001-4644). Verify that star wheels align with bale chamber before tightening down all hardware. Connect star wheel harness (006-7307EM2) to the star wheels and route back to IPM on the side twine box. Attach to square plug on bottom of IPM control module installed on side twine box

Star Wheel Mounting – UHD Balers
Locate parts bag E. The star wheels are to be mountedon top of the baler, just behind the knotters and under the walkway on both sides. The holes for the star wheel are precut. Remove the plate on top of the catwalk covering the triangle shaped access cutout. Place star wheel over the predrilled holes on both sides of the bale chamber, (shown below). Secure the star wheels with 5/16” x 3” BHCS (x2 each side) from the bottom side. Blocks are dropped down on the bolts and secured in place with the star wheel twine guards (001-4645, 001-4644). Connect star wheel harness (006-7307EM2) to the star wheels and route to the IPM. Attach to square plug on bottom of IPM control module installed on side twine box.

Installation of End of Bale Sensor
The end of bale sensor determines the position of the needles on the baler. When the needles cycle the sensor communicates this information to the Dual Channel Processor. This information is used for job records and will be used by the optional Bale Identification systems. Follow the steps below to mount the sensor. End of bale sensor bracket (001-4648) will be used. Cutoff excess metal not used during installation.

Mount the end of bale sensor bracket (001-4648) as shown in the 8” (20cm) hole position. Mark and drill two 3/8” (10mm) holes and attach the bracket using two 5/16” x 1” self-tapping screws, and 5/16” flange nuts.
Mount the sensor in the 8” (20cm) hole location, keep the sensor 1/4″ (7mm) from the needle arm and tighten both nuts. Cut off excess metal past the sensor. Run the sensor cable up to the main harness (006-765B2). Attach to the plug labeled EOB.

Tractor Setup

| 12V Battery Connection| The 12V battery connection must be at the tractor battery.
Connection to alternative locations such as an accessory port can cause problems with applicator system. MUST BE CONNECTED DIRECT TO TRACTOR BATTERY TERMINALS
---|---|---
| ISO Communication Module| The ISO communication module is to be mounted inside the cab.
Other mounting locations can lead to issues with weathering and operation. Once installed and the system is powered, a green light will turn on the ICM module.
| Key Power Connection| Ensure a solid keyed connection is found inside the cab and wired into. Poor keyed power connection can result in applicator system issues.
| Harness Connection to Baler| The tractor harness connects at the hitch to baler power/communication harness (006-765B2). This will allow the system components to communicate with one another. Ensure connections are debris and corrosion free.

Display Options

Optional Harvest Tec Display

Optional Tablet Display
The 700 series Harvest Tec Display will allow you to set your real time baling parameters to ensure the most precise application to every bale. This is done by utilizing the improved touch technology to select objects, enter data, and swipe through operational screens. The Harvest Tec Display offers easy integration by connecting to the additional CAN plug on the 006-765IC harness. Once, connected the Harvest Tec display will power up with applicator system.
Note: The Harvest Tec Display must be used as a standalone display, the baler cannot run both integrated and on the Harvest Tec Display. Must be one or the other. Removal of the 006-765VA or 006-765VAU (UHD balers) integration harness is required when equipped.

The iOS or Android Tablet displays offer the ability to communicate with the 700 series applicator system via hard-wired connection to the ISO Communication Module (ICM). Through the free Precision Baling App, the operator can set real time baling parameters to ensure the most precise application to every bale. This provides a multi-use option while utilizing the improved app to select objects, enter data, and easily switch through operational screens. The Tablet Display offers easy integration by connecting a charging cable to the USB port on the ICM module (USB port closest to LED light). Once, connected the Harvest Tec applicator will display upon opening the app and powering up the applicator system. Tablets can be used in addition to integrated baler VT display.  Made for iPad ® (3 rd generation minimum) or Android Tablet (Does not work with Amazon Fire). iPad is a trademark of Apple Inc., registered in the U.S. and other countries.
Optional Baler VT Integration

The 700 series integration to the Baler VT allows for the ability to set your real time baling though the baler VT and monitor both baler settings and Harvest Tec system parameters on one screen to ensure the most precise application to every bale.
The 700 series offers easy integration by connecting to the additional CAN plug on the 006-765B2 harness. Once connected the Harvest Tec system will display with power up of the baler and applicator system.
Baler Display Integration
The ISOBUS Monitor utilizes a combination of soft keys, number menus, and the scroll wheel on the upper right side of the actual monitor to make selections. Selections are made by scrolling the Thumb Wheel and pressing in once the selection is highlighted. All buttons are labeled and color coded.

Baler Monitor Setup
At any time after the initial Start Up/Power On the green “uploading data status bar (arrow A) may begin to fill. However, due to software version changes a status does not appear on all monitors. To begin setup of the HayBoss Preservative Applicator System select the fourth icon down on the right screen menu-the wrench icon (arrow B).

The service screen displayed below will appear. Here you can see the Version of Software for your baler which should be 3.30 or higher to enable working with the Preservative Applicator. Select the icon (arrow C) located at the bottom of the right selection menu to move to the next options menu.

Then select the ‘A B’ icon (arrow D) on the right side, this should be the top button.

Then select the ‘A B 2’ icon (arrow E) on the right side to enter the next baler options screen.

Use the thumb wheel to scroll and select the Harvest Tec Option (arrow F). Press the scroll wheel to open the drop-down menu.

Select the green check mark to turn the Harvest Tec option ON (arrow G). Then select the Baler Run Screen button (arrow H) to save the setting and proceed to the baler run screen.

Use the scroll wheel to select a container option on the baler run screen. Harvest Tec information can be displayed in any container on the baler run screen. Press the scroll wheel to open the drop-down menu and scroll to select the option and press the scroll wheel to select it. This will place the “Instantaneous” and “Last Bale” moisture values in this position on the screen.

Once the and moisture option is selected, the containers should show with a red background. The moisture information is denoted by a rain droplet for instantaneous and a rain drop with a back arrow above for the last bale average moisture. These values are separated by a slash. And a preservative sprayer icon will show in the top right corner of the screen (arrow K).
**NOTE: When the preservative sprayer icon is RED, the preservative system is not in a run mode (Auto or Manual). When the system is in a run mode, the icon will be GREEN. The HT Preservative and Moisture containers will have RED background when the system in not in a run mode. The background for the preservative and moisture container will be WHITE, matching the rest of the baler run screen when the system is in Auto or Manual mode.

Baler Monitor Setup / View – UHD Baler Only

Selecting the 700 Series Preservative Applicator
The soft keys down the left side of the monitor correlate with choosing connected implements or files.
Depending on your specific situation this could show your tractor, camera, baler, or the HayBoss Preservative Applicator System, among others. To enter the HayBoss menu screens, select the soft key next to the HayBoss icon (Arrow L). Once the HayBoss option has been selected, the Main Menu screen will show as seen below. The numbered and colored soft keys on the right side (1-6) correlate to the selection options on the screen. For example, Manual Mode is PURPLE, this correlates to the PURPLE number “3” soft key option on the right side (Arrow M). So, to enter Manual Mode, the scroll wheel can be used to select the button or the soft key next to the PURPLE number “3” option can be pressed. To return to the baler work screen select the baler icon (arrow O). The cycle button (Arrow P) can be used to toggle between connected implements. This is located at the bottom of the monitor next to the Home and Esc buttons.

Wiring Diagram – 700 Series

1. Connect the power harness (006-765IC) to the tractor battery (12 volt) using the red wire with fuse to the positive side and the black wire to the negative.
   A. The power harness must be connected to the battery!
   CONTACT HARVEST TEC BEFORE MODIFICATIONS.
   The unit will draw more amps than convenience outlets can handle. Any modifications of the power harness will void systems warranty
   B. This unit will not function on positive ground tractors.
   C. If the unit loses power while operating it will not keep track of accumulated pounds of product used.

2. The power harness on the tractor (006-765IC) will run from the tractor battery to the hitch. The power harness on the baler (006-765B2) will connect to the tractor power harness (006-765IC) at the hitch.

3. Connect the red keyed power wire (006-765CPH) to a keyed power source on the tractor. Connect the black keyed power wire to ground.
   The keyed power wire must connect to a keyed source or the unit will not power up correctly.

4. Attached the ISO Communication Module (006-6673) to the tractor power harness (006-765IC).

5. Attach the End of Bale (EOB) connection on baler harness (006-765B2) to the EOB Sensor (006-7401).

6. Attach star wheel (030-4642 U/UE) connection to ISO Pump Module on pump plate assembly.

System Wiring Diagram

Pin Outs

Integrated Control Module (ICM) on Tractor Harness 006-765IC (Deutsch Plug Number: DTM06-12SA)

ISOBUS Plug on Tractor Harness 006-765IC (Deutsch Plug Number: DT04-4P)

Power / Communication Tractor Harness 006-765IC at Baler Hitch (Deutsch Plug Number: HDP24-24-18PN)

Power / Communication Baler Harness 006-765B2 at Baler Hitch IPM (Deutsch Plug Number: HDP26-24-18SN)

Power / Communication Baler Harness 006-765B2 at IPM Module (Deutsch Plug Number: HDP24-24-18SN)

*IPM Module Whip Plug- Pin # 5 Not Used
Solenoid 1 Plug on Baler Harness 006-765B2 (Deutsch Plug Number: APTIV 12052641)

Solenoid 2 Plug on Baler Harness 006-765B2 (Deutsch Plug Number: APTIV 12052641)

CAN / IDM on Baler Harness 006-765B2
(Deutsch Plug Number: DT06-4S)

End of Bale Sensor Plug on Baler Harness 006-765B2 (Deutsch Plug Number: DT06-3S)

End of Row Sensors Plug on Baler Harness 006-765B2 (Deutsch Plug Number: DT06-3S)

Integration Harness Plug on Baler Harness 006-765VA (Plug: APTIV 12052848)

Pump Connection on 700 Controller Harness (16 AWG Two-Wire Plug)

Star Wheel Sensors

Ref| Description| Part#| Qty| Ref| Description| Part#| Qty
---|---|---|---|---|---|---|---
1| Star Wheel| 006-4642US| 1| 10| Star Wheel Nut| 006-4642U| 1
2| Dust Seal Gasket| 006-4642UG| 1| 11| Swivel Insert| 006-4642B| 1
3| Star Wheel Block (Avail. in 2024 Style Only)| 006-4642UB| 1| 12| Encoder Mount| 006-4512P| 1
4| 3/8” Wire Grommet| 008-0821A| 1| 13| Encoder| 006-4512E| 1
5| 3/8” Grommet Nut| 008-0821B| 1| 14| Electric Swivel| 006-4642A| 1
6A| Encoder Harness Plug (6 Pin)| 006-7307EM| 1| 15| Star Wheel Block Gasket (Fits Pre-2024 Block Style)| 006-4642UG| 1
6B| Moisture Harness Plug (2 Pin)| 006-7307M| 1| 15| Star Wheel Block Gasket (Fits 2024 and Newer Blocks)| 006-4642UG2| 1
7| Spacer (only used in some of the pre-2024 blocks)| 006-4642UBS| 1| 16| Block Cover (Fits Pre-2024 Block Style)| 006-4642UC| 1
8| Thrust Bearing Washer| 006-4642K| 2| 16| Block Cover (Fits 2024 and Newer Block Style)| 006-4642UC2| 1
9| Thrust Bearing| 006-4642TB| 1| | | |

Complete Assembly w/Encoder 030-4642UE
Complete Assembly No Encoder 030-4642U
Twine Diverters and Moisture Harness

Control Box and Wiring Harnesses

AGCO 2100 Series Baler-Pre 2012 will need 006-6650VAX
End of Bale Sensor Kit

Harvest Tec Inc. Warranty and Liability Agreement

Harvest Tec, Inc. will repair or replace components that are found to be defective within 12 months from the date of manufacture. Under no circumstances does this warranty cover any components which in the opinion of Harvest Tec, Inc. have been subjected to negligent use, misuse, alteration, accident, or if repairs have been made with parts other than those manufactured and obtainable from Harvest Tec, Inc.
Our obligation under this warranty is limited to repairing or replacing free of charge to the original purchaser any part that in our judgment shows evidence of defective or improper workmanship, provided the part is returned to Harvest Tec, Inc. within 30 days of the failure. If it is determined that a non-Harvest Tec branded hay preservative has been used inside the Harvest Tec applicator system where the failure occurred, then Harvest Tec reserves the right to deny the warranty request at their discretion. Parts must be returned through the selling dealer and distributor, transportation charges prepaid.
This warranty shall not be interpreted to render Harvest Tec, Inc. liable for injury or damages of any kind, direct, consequential, or contingent, to persons or property. Furthermore, this warranty does not extend to loss of crop, losses caused by delays or any expense prospective profits or for any other reason. Harvest Tec, Inc. shall not be liable for any recovery greater in amount than the cost or repair of defects in workmanship. There are no warranties, either expressed or implied, of merchantability or fitness for particular purpose intended or fitness for any other reason. This warranty cannot guarantee that existing conditions beyond the control of Harvest Tec, Inc. will not affect our ability to obtain materials or manufacture necessary replacement parts. Harvest Tec, Inc. reserves the right to make design changes, improve design, or change specifications, at any time without any contingent obligation to purchasers of machines and parts previously sold. Revised 4/17

HARVEST TEC, INC. P.O. BOX 63
2821 HARVEY STREET
HUDSON, WI 54016
PHONE: 715-386-9100
1-800-635-7468
FAX: 715-381-1792
Email: info@harvesttec.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>