hobbydrone 2 IN 1 Repeater Better Wireless Range Instruction Manual

2 IN 1 Repeater Better Wireless Range

“`html

Specifications:

• Voltage input: 2-6S Lipo
• RC IN Protocol: SBUS/CRSF, auto detection
• Video: 1.2G to 5.8G
• 5.8G VTX: 1.2W 48CH

Product Usage Instructions:

Radio System:

1. Solder the receiver with duppond cable, plug the receiver to
   the repeater.

2. Plug the ELRS/CRSF TX module to the repeater.

3. Bind the radio with receiver on repeater.

4. Bind the ELRS/CRSF TX module on repeater with drone
   receiver.

Video System:

1. Set the 1.2G VRX to match the CH on drones.

How to Change the CH:

Hold the button for 2 seconds to enter setting mode. Press the
button to change CH. If there is no button control for 3 seconds,
the VRX will save and exit the setting mode.

For stock antenna, it is suggested to use CH4/5/6/8 for the best
range.

VTX Setting:

Set the 5.8G VTX to match with the Goggles or ground
station.

FAQ:

How do I change the VTX settings?

To change VTX settings, follow these steps:

1. Hold the button for 3 seconds to enter setting mode.

2. In setting mode, short press the button to change the
   band.

3. Hold the button for 3 seconds to enter CH setting mode, then
   short press the button to change the channel.

4. To adjust power settings, hold the button for 3 seconds. A
   short bar on LED will indicate power levels – 1 bar for 200mW, 2
   bars for 800mW, and 3 bars for 1200mW.

“`

2 IN 1 Repeater Manual

Specs:
Voltage input: 2-6S Lipo RC IN Protocol: SBUS/CRSF, auto detection Video: 1.2G to 5.8G 5.8G VTX: 1.2W 48CH
How to use:
Radio System: 1.Solder the receiver with duppond cable, plug the receiver to the
repeater 2. Plug the ELRS/CRSF TX module to the repeater 3.Bind the radio with receiver on repeater 4.bind the ELRS/CRSF TX module on repeater with drone receiver
Video System: 1.Set the 1.2G VRX to matched the CH on drones
How to change the CH:Hold the button for 2s to in to setting mode, press the button to change CH, no button control for 3s,the vrx will save and quit the setting mode
For stock antenna, its suggest to use at CH4/5/6/8 to get best range.

CRSF_TX/S.PORT

CRSF_RX/SBUS

+5V

GND

TBS Receiver

GND

5V

TX

RX

GND 5V
S.port
Sbus Sbus In

Frsky R-XSR B P

1.2G VRX Setting Button

VTX Setting
Set the 5.8G VTX to matched with the Goggles or ground station

Band
Band A Band B Band E Airwave/FS Race Band L Band

1
5865 5733 5705 5740 5658 5362

2
5845 5752 5685 5760 5695 5399

3
5825 5771 5665 5780 5732 5436

Channel

4
5805 5790 5645 5800 5769 5473

5
5785 5809 5885 5820 5806 5510

6
5765 5828 5905 5840 5843 5547

7
5745 5847 5925 5860 5880 5584

1.Hold button 3 seconds into setting mode. 2.In setting mode. short press the button to change band. 3.Then hold button 3 seconds into CH setting mode, short press button to change CH. 4.Hold button 3 second to get into Power setting mode, there is short bar on LED, short
press to switch power, 1 bar means 200mW, 2 bar means 800mW, 3 bar means 1200mW.

8
5725 5866 5945 5880 5917 5621

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>