HUMAN CARE 10624 Slow Down Brake Instruction Manual

HUMAN CARE 10624 Slow Down Brake Instruction Manual

Accessory Overview

| Tray
Practical for resting light weight items.| C-O & Rebel:
all sizes: 10651
C-O RA/TW, Rebel RA/TW with seat
Staffan RA/TW, Svea TW:
Not available
| Cane holder
Simplifies the transportation of a cane or umbrella.| C-O & Rebel, C-O RA/TW, Rebel RA/TW:
10603
Staffan RA/TW:
40603
Svea TW:
Not available
| One-hand brake
Allows the user to control brake functions with one hand.| C-O & Rebel, C-O RA/TW, Rebel RA/TW:
10652
C-O RA/TW, Rebel RA/TW, Svea TW:
10653
Staffan RA/TW:
10653 (low) 10654 (high)
| Backrest
Gives support to the back while seated.| C-O and Rebel:
57 cm, 62cm and 67 cm models: 10621. Part no. for 72cm model: 10655
All other models:
Not available
| Curb climber
Helps raise the rollator onto a curb.| C-O & Rebel, C-O **RA/TW, Rebel RA/TW, Svea TW:
10612
---|---|---
Staffan RA/TW:
Not available
| Splash guard
Protects legs and clothes.
Sold in pairs.| C-O, C-O RA/TW:
10608
All other models:
Not available
| Oxygen holder
Holds oxygen tube firmly in place.| C-O & Rebel, C-O RA/TW, Rebel
RA/TW:
10615
Staffan RA/TW:
40605
Svea TW:
Not available
| Basket with handle
Basket ideal for shopping.| C-O & Rebel, C-O **RA/TW, Rebel
RA/TW:
10605
Staffan RA/TW:
40601
Svea TW:
Not available
| Bag
Kit of two bags that offers storage space for shopping or personal belongings.| C-O & Rebel:
Carl-Oskar and Rebel 57 and 62) Part no:
Carl-Oskar and Rebel 67 and 72) Part no:
---|---|---
C-O RA/TW, Rebel RA/TW:
Not available
Staffan RA/TW, Svea TW:
Not available

Assembly Tray

Carl-Oskar, Rebel, C-O RA/TW, Rebel RA/TW
The tray rests on the seat of the rollator (see icture). Wrap tray clip on one side and push down firmly into position with both hands.
Remove from the seat by pulling up from the back side of the tray.
For the RA/TW models the tray is only suitable for models with a seat. Maximum weight: 5 kg.

Assembly Cane Holder

Assembly – Upper Part
Verify that you have all components before assembly. The cane holder comes in two parts – an upper and a lower part – both of which are composed of two separate pieces.

1. Open the clamp that is secured to the frame tubing so that the clips come closer to each other.

2. Fit the cane holder hole through the clips of the attachment. Release slightly so that the cane holder is secure and place the clamp
   around the handle frame.

3. Close the clamp and tighten with the screw, taking care not to strip the screw. Note! Make sure that the attachment is secured.

Assembly – Lower Part

1. Open the clamp that is secured to the frame tubing so that the clips come closer to each other.
   

2. Fit the clips into the cup hole and release slightly to secure. into position.
   Turn the cup into the correct position to hold the cane/umbrella bottom tip before securing onto lower frame.
   

3. Close the clamp and tighten with the screw, taking care not to strip the screw. Note! Make sure that the cup is secured.
   

Assembly One-Hand Brake

The one-hand brake allows the user to brake the walking-aid with one hand.
The single hand brake can be assembled afterwards or be ordered as pre- assembled unit.
When ordering pre-assembled, please state on which side of the walking aid the handle should be placed.

Disassembly

1. Disassemble the cables from the wheels on both sides of the rollator. Disassemble the end cover (1) from the brake housing (5) and remove the cables and cable housings from the rollator.
2. Remove the brake lever (2) on the side that will not be used as a one-hand brake.

Assembly

1.  Attach the two adapters (6) into the end cover (7).\
2. Pull through the two assembled cables and reattach into the end cover (7). Pull the cables through the housing (5) and around the washer (3) and secure it to the brake lever with the brake handle pin (4). Attach the brake lever to the housing.
3. Assemble the shorter cable assembly to the bottom wheel on the side where the one-hand brake is placed. The longer cable assembly should be attached to the other wheel.
4. Adjust the brake with the adjustment screw for increased / decreased braking action.
   

Assembly Back Support

• The back support comes with the following parts:
  A: Holder (2/ea)
  B: Holder (2/ea)
  C: Screw M4x14 (4/ea)
  D: Screw M4x20 (4/ea)
  E: Nut M4 (8/ea)
  

The back strap can be cut to achieve different lengths.

Fold one end over onto the other side to the desired length (so they overlap each other).
Using the existing holes from the top belt as a guide, mark the hole positions and the cut required for the end.
Note! The distance from the hole to the end should be 7mm.

Use a hole puncher to punch the holes in the positions marked. Cut the end using a belt cutter.

Assembly onto a Rollator

Line up clamps on both sides of the rollator tubing at the bend as shown.
Place the backstrap between the two clamps, lining up the holes.
While holding the backstrap, press clamp A with clamp B and secure in position with screws.
Take care not to strip the screws while tightening. Screw D is used to secure closest to the frame and screw C is used to secure the backstrap.
Do not rest anything on the back support as damage may occur. Check frequently for any loose, cracked or corroded plastic. Check frequently to ensure screws are tightened firmly.

Assembly Curb Climber

1. Remove existing bolt and nut.

2. Assemble the curb climber on the inside of the rollater (between the wheels) on either the right or left side according to the
   suggested heights indicated in the table.

3. Secure in position with new bolt and nut.

The curb climber has three holes for height adjustment which allows it to be suitable for the Carl-Oskar, Rebel and Svea, and also
allows height adjustment from ground level to accommodate the user’s requirements.

Height Adjustment Table (suggested distance between curb climber and ground).

Note! Bolt and nut must be replaced when adding a curb climber. Do not re-use existing bolt and nut

Using the Curb Climber
Place the foot onto the curb climber to act as a lever and raise the rollator slightly upwards towards you to raise the front wheels. Place
onto a curb. Do not step on the curb climber!

Assembly Splash Guard

Place the splash guard onto the rear wheel and secure on the inside of the rollator by securing the attachment on to the rear fork.

Assembled on the rollator

Assembly Oxygen Holder

Assembly – Oxygen Tank
The oxygen holder is delivered complete with two preassembled straps.

1. Loosen the straps before the tank is put in lace by pushing the lock, on the strap, and pulling out the loop to preferred size.
   

2. Tighten both straps when the tank is in place to secure it.

Assembly – On Rollator

1. Tilt the oxygen holder and pull it through the upper gate. The holder shall be placed in the middle of the gate.
   

2. Hook the oxygen holder to the lower tubes of the gate and tilt it back (vertically) so that the upper attachment on the holder slides under the upper tubes of the gate.

3. Ensure the oxygen holder is secure before use.
   

Assembly Basket

C-O & Rebel, C-O RA/TW, Rebel RA/TW:
Place and attach the basket onto the hooks with the straight side of the basket against the gate (see picture). Note! Basket can only be used when the rollator is in the unfolded position. Max load 10kg.

Staffan RA/TW:
Assemble the basket onto the rollator by hanging the basket on the hooks on the front of the rollator.

Assembly Bag Kit

Attaching the small bag

• The small bag is placed with the opening towards the user for easy access to personal belongings.
  

• Center the bag onto the middle of the rollator seat.
  

• Using the velcro straps located on either side of the bag, secure tightly onto each frame handle.
  

Attaching the big bag

• Place the bag into the hard basket, pushing down so it is a snug fit. Ensure that the back of the bag flap is secured as shown.
  

• Ensure that the front is secured as shown.
  

• Snap all the push buttons around the bag to secure into position.
  

• Attach the basket with the inserted bag onto the rollator.
  

CUSTOMER SUPPORT

HUMAN CARE UNITED STATES
4210 S. Industrial Drive, Suite 160 Austin, TX 78744
Phone: 512.476.7199
Fax: 512.476.7190
Email: info.us@humancaregroup.com
www.humancaregroup.com

References

• comhumancaregroup.com
• Safe Patient Handling Products and Walking Aids - Human Care
• Safe Patient Handling Products and Walking Aids - Human Care

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>