EMPAVA EMPV-71JT802L Massage Bathtub User Manual

EMPV-71JT802L Massage Bathtub

“`html

Product Specifications:

• Model: EMPV-71JT802L
• Size: 5.9 feet
• Features: Transferable switch, hot water/cold water overflow,
  hydrodynamic adjust, water inlet shower head, backwater drainer,
  bubble nozzles massage jets, pillow rest, computer-controlled

Product Usage Instructions:

Electricity Connection:

User needs to purchase two separate 110/120V 15amp plugs and
install the proper dedicated plug with a ground electrode to the
power line. Ensure the plug is inserted firmly. The product uses
universal home power with external circuitry equipped with high
sensitive and fast type leakage protection switch.

Installation:

The product should be installed alongside ground and electric
leakage switches by a licensed electrician. Connect the ground wire
from the switch to the ground terminal of the motor and stainless
steel frame. The bathtub must be connected to the ground and power
outlet must be sealed well.

Operation Guide:

• Press the button shortly to start the system; the display area
  will show the current temperature.

• To turn off the system, shortly press the button when it is on.
  It will auto turn off in two minutes if there is no operation.

• Air Pump: Press the button to turn on/off the air pump. The
  pump starts with maximum wind and changes to default setting level
  in 2 seconds.

• Water Pump: Instructions for operating the water pump are not
  provided in the manual extract.

Testing:

Insert the plug and start all functions for a few minutes,
including massage functions. Inspect the tub thoroughly for any
defects before installation to ensure warranty coverage.

Frequently Asked Questions (FAQ):

Q: How do I connect the electricity?

A: User needs to purchase two separate 110/120V
15amp plugs and install the proper dedicated plug with a ground
electrode to the power line. Ensure a licensed electrician installs
alongside ground and electric leakage switches.

Q: What should I do before installing the bathtub?

A: Ensure the bathtub is connected to the
ground, power outlet is sealed well, and inspect all wires for
intact surfaces. Test all functions for defects before installation
for warranty coverage.

“`

This product uses universal home power.
MASSAGE BATHTUB
MODEL: EMPV-71JT802L
5.9

transferable switch

Size chart

The drain pipe is 31.5″ long and the ground drain

12

should be 12″ ­ 20″ away from the bathtub drain so

that the drainpipe can form an S-bend for

odor isolation

hot water/cold water

overflow

71″

hydrodynamic adjust

water inlet shower head

42″

Backwater
drainer bubble nozzles massage jets

pillow rest
18.9″

Computer-controlled
71″ 3.1″
25″

H ow to connect the e le ctricity? User needs to purchase two separate 110/120V 15amp plugs and
install the proper dedicated plug with a ground electrode to
the power line. Then insert the plug frmly. Note: This product uses universal home power.
External circuitry is equipped with high sensitive and fast type
leakage protection switch. (Induced current rating below 15MA; trip
time should be less than 0.1 second; rated current is above 30A.)

Notice

The product should be installed alongside ground and electric leakage switches by a licensed electrician.

Make sure the ground is connected. One side of the ground should be connected to the ground terminal of the motor and the stainless steel frame; the other side should be connected to the ground wires of the plug.

Tomaincontrolbox N
L
From electrical source 110-120V
Ground terminal The ground wire from the switch goes into this screw

Although all our massage bathtub are water tested before they leave our factory,

Notice

The bathtub must be connected to the ground. The power outlet must be sealed well. Make sure the surface of each wire is intact.

d. Insert the plug, start all the function for few minutes (which includes the functions of massage ), inspect the tub completely any defect must be reported to your dealer/distributor prior to installation in order to have it covered under warranty.

Filter screen

H2208 Control panel operation Water Pump Air Pump
Display Area

Minus key

Lighting

Add Key

Thermostat FM/Bluetooth Setting Key

FM Channel Save OFF/ON

Function 1Air Pump 2.Water Pump 3.Thermostat 4.Lighting 5.FM/Bluetooth music player

6.Ofunction

Operation guide

On/Off

1. start the system

Shortly press the button to start the system, the display area will shows the current

temperature.

turn off

When the system is on, it will auto turn off in one hour.If have the operation,it will reset time for 1

hour.

When the system is on, shortly press the button to turn off the system.

If there is no operation after the system is on, it will auto turn off in two minute. When power is on,

the buzzer will short beeps.

Air Pump

When the bathtub is full of water, shortly press the button to turn on the air pump. The icon of

the button will be lit .The air pump will start with the maximum wind and will change to the default

setting level in 2 seconds. Shortly press the button

again can turn off the air pump.

When the air pump is on, if the bathtub change to less of water, the air pump will be auto off.

When the bathtub works in lack of water condition, the back-light of the button will be lit,The air

pump will turn off after starting with maximum wind in 10 grade for 5 minutes. It will turn off the air

pump when detects with water again in 5 minutes.

Water Pump

hortly press the button to turn on or turn off the water pump function. When the water pump is

on, if the bathtub is full of water, the button will be lit and the water pump works. If the bathtub

lacks of water, the water pump will stop and the back-light of the button will flashes. If the bathtub

is full water again, the water pump works again.

Thermostat

When the bathtub is full of water and water pump function is on, shortly press the button to

open the thermostat function. After thermostat function is on,the icon is lit.Shortly press the

button again can turn off the thermostat heating.

When the thermostat function is on,if the water temperature is 1 degree C lower than the setting

temperature, the thermostat heater will be auto heating until the water temperature is higher

than or equal to the setting temperature. At this time the heater will stop heating. When close the

water pump, the thermostat function will auto off.

After open the thermostat function, the screen shows the setting thermostat temperature and the

icon

is flashing ,after two seconds showed the setting temperature,it will showed the current temperature,the icon will be always lit.

If the bathtub lacks of water and the thermostat function is on, the heater will stop heaatinndgthe icon

will be flashing. If the system detects full water again and water pump is on, the heater will be auto

heating again. When the thermostat function is on.T he first time shortly press to enter the setting of the thermostat
temperature,the icon is flashing and show the temperature on the display area.At this time press the

button or to adjust the thermostat temperature. T he range is from 25 to 45 degree C.

Lighting

When the system detects full water, shortly press the button to open the lighting function and the

icon will be lit. Press again can close the the light and the icon will be off. When the light is on and the

bathtub is less of water, the icon will be flashing. After the bathtub is full of water again, the light will

auto open again.

T he first time shortly press the audio switch key to turn on the radio and the display area will shows the

current radio channel. Icon is bright. T he second time shortly press the button and enter the

Bluetooth station .Icon is bright and the

is dark. T he third time shortly press the audio switch

key to close the Bluetooth function.

When FM is on, at this time press the button or to adjust the volume. is for louder volume, is

for lower volume .Press the icon

until to the flashing

appear, press the button or to

adjust the radio channel.Shortly press icon for next channel,or for last channel.Long press for

1.5 second to search the next channel,or to search the last channel. T he range is :87.5MHz-108.0MHz.
When the radio function is on,press key MEM for 1.5 second to save the channel,Shortly press MEM to exchange the channel,range 110-.

Bluetooth Music Player

When system is on for 5 seconds, use the B luetooth function on your smart device to serach the

B luetooth of the bathtub.And it will auto disconnect for of-fsystem in 10 seconds.Shortly press to switch to Bluetooth music player and the icon is bright.If it doesn’t connect,the icon is

flashing.It will appear bt.F character.If it connect successfully,the icon is bright steady,and show

bt character.

When Bluetooth is playing, shortly press the button or to adjust the volume.Icon

is

for louder volume, is for lower volume.Shortly press the icon

until to the flashing

appear, press the button or to adjust the music. Shortly press icon

for next

song,or for last song.

Bluetooth music player instructions

A.Connect the smart device to Bluetooth after the system is on for 5 seconds ;

B. After successful connecting,open the music player on mobile phone,play the song;

C. Shortly press the icon

to switch to the Bluetooth music function.

D.If it shows bt.F character on display area when the Bluetooth is on,it means it fail to connect and please re –
Panel Lock and Unlock

If there is no operation in 30 seconds or press the SET/Lock Key 1.5 seconds,the panel is locked and all key

is invalid.Shortly press

to unlock.

function
It will auto start the Ofunction after turning off the system for 30 seconds,Icon auto turn off,and the icon will be off.
If start the system while O function is on,and it will stop Ofunction.
Parameters Setting

is bright.After 10 minutes,it

Setting Mode Choice:

When the audio is on,both and are used to adjust the volume,range:0 -15dB;

Touching the setting on the panel,choose the parameters mode.The operation is as below: The first time to press the setting key to control thermostat temperature,the screen shows the setting degree
C.Icon is flashing.(please skip this step if thermostat temperature function is off.) T he second time to press the setting key to control the volume, Icon is flashing (Please skip this step if the FM/Bluetooth function is off.) The third time to press the setting key to adjust the radio channel,searching channel or Bluetooth switch

songs.

is flashing.(Please skip this step if the FM/Bluetooth function is off.)

The fourth time to press the setting key to adjust the wind speed.The screen show the wind speed,such as L5.(Please skip this step if the wind pump is off.)

Parameters Setting: 1.Adjust channel:Enter to the frequency adjust station,press the “add or reduce “key to control the frequency;Long press “the add and reduce “key to the searching channel station.

2.Volume:The range of volume is 1 -10 grades. 3.Adjust/ search channel:When adjust the channel,shortly press

to add 0.1MHz,shortly press to

minus 0.1MHz.When search the channel,long press

1.5 seconds to search upward channel,long press

1.5 seconds to search downward channel,it will stop until searching the valid channel.

4.Wind speed adjust: Enter to adjust the speed of wind pump,touching the “add or reduce “key to control the speed up or down.The range is 1 -10 grade.

5.5.Thermostat Temperature adjust:Enter to adjust thermostat temperature station,touching the “add or reduce “key to increase or reduce the thermostat temperature.T he range is 25 -45 degree C.

Technical parameters:

Rated Working condition and characteristic

Rated voltage Rated current Insulation resistance

AC220

Frequency

15.7A

Rated power

20M

Waterproof

Load parameters

50Hz 3450W IPX5

Loads Thermostat Water Pump Air Pump Light Ozone Speaker

Rated voltage
AC220V AC220V AC220V A C12V DC12V
–

Frequency
50Hz 50Hz 50Hz 50Hz50Hz
–

Rated power
2KW 1KW 400W 10W
6W
8/ 10w

Other
–

Control panel Size

Control panel Control box

Length Width =12075 (mm) Length Width Height =27521892 (mm)

Fault Code Fault Name Fault Reason

Trouble shooting

E16

Temperature probe failure

AtBc..eiTNmrpceomeuprieatrt.auctrouenrnepercpotrbionebge

is

the open

AtBopt..hfleeCCemapphhsreteeeeorccmkbakeetpxit,uefhcrirefhiaetatcdinupsoogrrneceoensobnepnetrcnthtoeceebcdoetnewnnodeeirrwcettnoot;

E17

Temperature probe short circuit

Tciermcpueirtature Probe

is short ApBcpo..raCnCnonebhheleeac;cintksgieiofsnhttoehrmetpoefcrtiaerttcmhuupeireteroamprtrounotroobetre.

DOrisplay Cloingthrtol bright

E2 Cbroemamkudnoiwcantion box
is

Tcioshnentolritgohlbtriobgfohxt CProonbtlroelm

Motor

AmsBdCtch..h.oioeITTotsntrponhhtlreeemacsymcotboirobonwrtrxootocoixrbtruraerinoatdmcdknoaooederctmtnsochmmonnheupontnestebnoiwccerrcoctetar.wietknreitceohoiunrsenitAcBnCi.t…oomCCCmmapahhhculeeehtccckkeokwrrtiihnfitwefohttirmhrt;ioegeh;theotmrocdtoiponsrronpcelecwastyost,rhikbfeox?

Twhoahrvekeipncrgoonbotlerrmothl e

motor motor

stop power

Cmohtaonrg.e

to the new control

Ozone quickly checkL:ong press turning off the function. Enter to the aging mode:Shortly press third times,and then long press 1.5 seconds to open the aging mode.Turning on all function,water pump,air pump,constant temperature and lighting is not controlled by the water level.It will be on for 6 hours.It sLhHows be out of aging mode.
Installation wiring diagram

Open

Close

waterfall sprinkler

cold

A

hot

B

Press this switch to adjust the shower jet mode.

SHOWER INSTALLATION
SHOWER HEAD RUBBER GASKET HOSE CONNECTOR SHOWER HOLDER
BATHTUB
SHOWER HEAD INSTALLATION Tmaking sure it lies flat.o install the shower head, follow the steps shown in Figure A. First, remove the hose connector from the shower holder. Then, insert the rubber gasket into the hose connector, Finally, tighten the shower head and the hose connector securely.

Whirlpool Suction Cover/Strainer Maintain regular cleaning of the suction cover/strainer 1. Rotate the suction cover to the left to detach it. 2. Remove any hair, lint, or debris present on the cover and
housing. 3. Remember to reattach the cover in place.
WARNING! Please orient the cover/strainer with the small notch at the bottom. The gasket must be inserted into the groove of the cover/strainer before mounting it onto the suction ftting. DANGER: RISK OF SEVERE INJURY OR DROWNING!
a. Keep hair a minimum of 6 inches (152 mm) away from the suction ftting at all times when the whirlpool system is operating. Individuals with shoulder- length hair should secure it close to their heads or wear a bathing cap.
b. Do not operate the Whirlpool system with the suction cover/strainer removed! It is a safety device and must always be in place on the suction ftting to minimize the potential hazard of hair and body entrapment.
Always implement countermeasures that help prevent freezing. You must empty the bathtub and the water in the pipe during winter use. If the pipes freeze, the pipes could rupture or equipment could become damaged. Use no water other than standard tap water. The use of well water could cause corrosion, which could lead to leaks.
The bathtub should not be exposed to ultraviolet or bright light, otherwise aging could be accelerated, causing damage.
Keep the bathtub away from cigarette butts, hair dryers, and other heat sources, otherwise the product may be damaged due to high temperature deformation.
When not in use, please keep the bathtub well-ventilated and dry; avoid contact with corrosive substances; cut off electricity and cut off water supply.
To avoid other damage, please do not drop or strike the bathtub with hard objects. Doing so could crack or scratch the bathtub or cause leaks that damage or ruin household property.
When the product is at work, you cannot cut off any connection lines and split the bus master and control panel. Any part of the control panel and the bus master CAN NOT be split by the user. Doing so may cause product leakage, electric shock, or other accidents. The ground fault circuit interrupter (GFCI) should be tested regularly. It is ideal to test before each use.
Use water or mild detergent to clean the product. Do not use acids, alkalis, chemical organic solvents, or acidic/alkaline cleaning agents. Otherwise, the bathtub will experience surface damage. When water or a neutral detergent cannot remove stains, use a clean cloth with a little alcohol to remove stains. Plating parts maintenance: use cotton fabric to scrub.
Light scratches and dulled areas may be restored to original luster by coarse grinding using NO. 1200 waterproof sandpaper dipped in water. Then fne grind by using NO. 2000 waterproof sandpaper dipped in water. Finally, polish with a soft cloth and a polishing agent.
When not in use, please keep the bathtub well-ventilated and dry; avoid contact with corrosive substances; cut off electricity and cut off water supply.

Water level speaker

Working Indicator
Water Pump power
Temperature Probe Display box

Air pump power C onstant temperature Power AC 220V input

Care and Maintenance
Regular bathtub maintenance will keep it clean and working at its best. Pump and pipe circulation systems should be fushed before frst use and on a monthly basis when product is under normal use. Below is the recommended cleaning procedure: 1.Do not run the jet massage system dry. 2.Fill the tub with hot water (about( 40°C ) 2-3 cm (0.9-1.2 inch) above the jets. Add 2-3
teaspoons of low foaming detergent, such as dishwashing machine detergent. 3.Turn on all the functions and run for 10 minutes.
4.Drain tub completely. 5.Fill tub with cold water above jets. 6.Turn on all the functions and run for 15 minutes. 7.Drain tub completely. 8.Clean the “suction cover” by removing any hair or lint.

Empava® APPLIANCES
IF YOU NEED SERVICE: Empava Customer Center Email: support@empava.com Address: 15253 Don Julian Rd, City of Industry, CA 91745

PROOF OF PURCHASE IS REQUIRED TO OBTAIN WARRANTY SERVICE.
Please have the following information available when you call/ email the Empava Customer Center: · Proof of purchase (PO# or screenshot of order confrmation) · Model number and serial number · A clear and comprehensive description of the issue
Website: https://empava.com Call: 888-682-8882 Monday – Friday from 9am – 5pm PST

Empava® APPLIANCES WARRANTY WHAT IS COVERED

WHAT IS NOT COVERED

TWO YEARS WARRANTY (PARTS)

1. Commercial, non-residential or multiple-family use, or use

Empava offers a two-year warranty on parts for the following

inconsistent with published user, operator or installation

categories: induction cooktop, gas cooktop, electrical oven,

instructions.

pizza oven, fre glass, juicer, range hood, wine cooler, beverage 2. In-home Instruction on how to use your product.

refrigerator and toilet seat

3. Service to correct improper product maintenance or

installation, installation not in accordance with electrical or

TWO YEARS WARRANTY (PARTS & LABOR)

plumbing codes or correction of household electrical or

Empava offers a two-year warranty on both parts and labor for plumbing (i.e., house wiring, fuses or water inlet hoses).

the following categories: gas oven and gas range.

4. Defects or damage caused by the use of non-genuine

Empava parts or accessories.

THREE YEARS WARRANTY (PARTS & LABOR)

5. Conversion of your product from natural gas or L.P. gas.

Empava provides a three-year warranty on both parts and labor 6. Damage from accident, misuse, abuse, fre, foods, acts of

for the following categories: freestanding tub, massage tub, and God or use with products not approved by Empava.

walk-in tub.

7. Repairs to parts or systems to correct product damage or

defects caused by unauthorized service, alteration or

This limited warranty is valid for products that are either

modifcation of the appliance.

purchased brand new from an authorized Empava dealer or 8. Cosmetic damage including scratches, dents, chips, and

directly from Empava.

other damage to appliance fnishes unless such damage

The effective date of the warranty commences from the date of original consumer purchase. If the appliance is installed, operated, and maintained in accordance with the user manual, Empava will provide parts at no cost to rectify any defects in materials and workmanship that were present at the time of purchase. Alternatively, at its sole discretion, Empava may replace the product. In the event of product replacement, the warranty for the replacement product shall be valid for the remaining term of the original warranty period.

results from defects in materials and workmanship and is reported to Empava within 30 days. 9. Discoloration, rust or oxidation of surfaces resulting from caustic or corrosive environments including but not limited to high salt concentrations, high moisture or humidity or exposure to chemicals. 10. Food loss due to product failure. 11. Removal or reinstallation of inaccessible appliances or built-in fxtures (i.e., trim, decorative panels, fooring, cabinetry, islands, countertops, drywall, etc.) that interfere with servicing, removal or replacement of the product.

DISCLAIMER OF IMPLIED WARRANTIES IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow limitations on the duration of implied warranties of merchantability or ftness, so this limitation may not apply to you. This warranty gives you specifc legal rights, and you also may have other rights that vary from state to state or province to province.
DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance, you should ask Empava or your retailer about buying an extended warranty.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES·
HEREIN. EMPAVA SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specifc legal rights, and you also may have other rights that vary from state to state or province to province.

WARNING! CALIFORNIA RESIDENTS Cancer and Reproductive Harm AVERTISSEMENT! RÉSIDENTS DE CALIFORNIE Cancer et Dommages à la Reproduction ¡ADVERTENCIA! RESIDENTES DE CALIFORNIA Cáncer y Daño Reproductivo w w w .P 65W arnings.ca.gov
EMPAVA APPLIANCES INC. 15253 DON JULIAN RD CITY OF INDUSTRY,CA 91745 TEL:888-682-8882 WWW.EMPAVA.COM

References

• AREA Design & Möbel in Salzburg, Linz & Wien

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>