ideal lux Admiral PL8 Wall and Ceiling Lamp Instruction Manual

ideal lux Admiral PL8 Wall and Ceiling Lamp

Product specifications:

• Brand : Admiral
• Model : PL8 G9
• Maximum Wattage : 8 x 40W
• Voltage : 220-240V, 50/60Hz
• Product Code : 8021696080352
• Material : Chrome

Product Usage Instructions

Installation:

• The lighting fitting should be installed by a qualified electrician.
• Follow the assembly instructions by reading the numerical progression provided.

FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION

Energy Efficiency:
This product is provided with a light source with an energy efficiency class of F.

Light Source Information:

• Replaceable light source by an end-user.
• Replaceable LED light source by an end-user.
• Replaceable light source by authorized personnel only.

Control Gear:

• Replaceable control gear by an end-user.
• Replaceable control gear by authorized personnel only.

Safety Instructions:
European Safety Standards:
Compliant with European safety standards EN 60 598-1.

Additional Safety Instructions:

1. According to regulations, the installation should be done by a qualified electrician.
2. If the external power cable is damaged, it should be replaced only by the manufacturer, retailer, or a qualified electrician.
3. Always disconnect the power supply before installation or any maintenance work.
4. The device has parts that can get hot, and handle with care.
5. Use specific fastening accessories suitable for the material during installation.

Dimension

SYMBOLS

This product is provided with a light source with efficient energy class of:

EAN: Energy Efficiency Class 8021696209043 F

LEGENDA ICONE

SAFETY INSTRUCTIONS

1. This fitting is produced and tested in accordance with the strictest European safety standards (EN 60.598-1).
2. This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
3. As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
4. If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
5. Always isolate power before commencing installation, maintenance or repair.
6. The luminaire contains certain parts which can be very hot.
7. Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
8. Always tighten the screws firmly to avoid contact problems.
9. This fitting should only be installed indoors.
10. Luminaires not suitable for recessed on normally flammable surfaces.
11. Luminaire not suitable for direct mounting on normal flammable surfaces.
12. This fitting is only suitable for fixing to the ceiling.
13. This fitting is only suitable for fixing to the wall.
14. The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
15. Only use lamps which do not exceed the maximum specified wattage.
16. Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
17. Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
18. Cracked or broken safety glass has to be replaced immediately. Use only manufcturer approved parts complying with regulations.
19. Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
20. This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
21. Class I Electrical safety guaranteed by the main insulation and an additional protective conductor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
22. Class II Electrical safety guaranteed by the main insulation and a double or reinforced insulation. Earthing not necessary.
23. Class Ill Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
24. Not protected.
25. Protected against solid objects greater than 50 mm.
26. Protected against solid objects greater than 12 mm.
27. Protected against solid objects greater than 2,5 mm.
28. Protected against solid objects greater than 1mm.
29. Dust protected.
30. Totally protected against dust infiltration.
31. Not protected.
32. Protected against vertically falling water drops.
33. Protected against water drops falling with a maximum angle of 15° to the vertical axis.
34. Protected against rain.
35. Protected against splashing water.
36. Protected against water jets.
37. Protected against strong water jets.
38. Protected against temporary immersion.
39. Protected against prolonged immersion.
40. Luminaire not suitable for covering with thermally insulating material.
41. Caution, risk of electric shock.
42. Do not stare at the operating light source.

FAQ

Q: Can I replace the light source myself?
A: Yes, this product allows for the replacement of the light source by the end-user.

Q: What is the maximum wattage supported?
A: This product supports a maximum of 8 x 40W bulbs.

Q: Is the product compliant with European safety standards?
A: Yes, this product complies with European safety standards EN 60 598-1.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>