ideal lux Sole SP1 D50 Sole Pendant Light Instruction Manual
- August 24, 2024
- ideal lux
Table of Contents
ideal lux Sole SP1 D50 Sole Pendant Light
Product Specifications
- Model: Sole SP1 D50
- Socket Type: E27
- Maximum Wattage: 1 x 60W
- Voltage: 220~240V, 50/60Hz
- Color: BIANCO
- Manufacturer: IDEAL LUX srl
- Country of Origin: Italy
Product Usage Instructions
Installation:
The lighting fitting should be installed by a qualified electrician following the assembly instructions provided in numerical order.
Safety Instructions:
- Ensure the installation is carried out by qualified personnel.
- Always disconnect the power supply before installation or maintenance.
- Use appropriate fixing accessories for the material where the fixture will be mounted.
- Do not look directly at the light source.
Maintenance:
If the lamp does not turn on, replace the fuse. Do not attempt to disassemble the LED light source.
Electrical Safety Classes:
- Class I: Requires grounding for electrical safety.
- Class II: Does not require grounding due to double insulation or reinforced insulation.
- Class III: Operates at very low voltage and does not require grounding.
FAQ
Frequently Asked Questions
- Q: Can I replace the LED light source?
- A: The LED light source is non-replaceable. Do not attempt to disassemble it.
- Q: What should I do if the lamp does not turn on?
- A: Replace the fuse. If the issue persists, contact the manufacturer or a qualified electrician for assistance.
- Q: Is grounding mandatory for this lighting fixture?
- A: For Class I fixtures, grounding is mandatory to ensure electrical safety.
Product Information
- Suspension lamp
- E27 max 1 x 60W / 220~240V
- 50/60Hz
- 8021696136011 BIANCO
Dimensions
Symbols
Installation Instructions
FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
SAFETY INSTRUCTIONS
- This fitting is produced and tested in accordance with the strictest European safety standards (EN 60.598-1).
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
- Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems.
- This fitting should only be installed indoors.
- Luminaires not suitable for recessed on normally flammable surfaces.
- Luminaire not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing to the ceiling.
- This fitting is only suitable for fixing to the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps which do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
- Cracked or broken safety glass has to be replaced immediately. Use only manufcturer approved parts complying with regulations.
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
- Class I Electrical safety guaranteed by the main insulation and an additional protective conductor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
- Class II Electrical safety guaranteed by the main insulation and a double or reinforced insulation. Earthing not necessary.
- Class III Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
- Not protected
- Protected against solid objects greater than 50 mm.
- Protected against solid objects greater than 12 mm.
- Protected against solid objects greater than 2,5 mm.
- Protected against solid objects greater than 1mm.
- Dust protected.
- Totally protected against dust infiltration.
- Not protected.
- Protected against vertically falling water drops.
- Protected against water drops falling with a maximum angle of 15° to the vertical axis.
- Protected aqainst rain.
- Protected against splashing water.
- Protected against water jets.
- Protected against strong water jets.
- Protected against temporary immersion.
- Protected against prolonged immersion.
- Luminaire not suitable for covering with thermally insulating material.
- Caution, risk of electric shock.
- Do not stare at the operating light source.
Contact
IDEAL LUX s.r.l.
- Via Taglio Destro 32 30035 Mirano (VE) Italy
- www.ideal-lux.com
IDEAL LUX Warehouse
- Via delle Industrie, 8/D
- 30036 Santa Maria di Sala (Venezia)
- 8.00 – 12.00 / 13.30 – 17.00
Read User Manual Online (PDF format)
Loading......