YeCeny YC-ANT001 TV Remote Controlled Rotating Antenna User Manual
- August 20, 2024
- YeCeny
Table of Contents
YeCeny YC-ANT001 TV Remote Controlled Rotating Antenna
FCC
Caution:
The user is cautioned that changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
TV REMOTE CONTROLLED ROTATING ANTENNA
Installation of the components
Durable
Use the new material and streamline shape in an improved feature for overall
and complete seal up against wind and sunshine.
Easy to install
Use Sophisticated unity design to avoid complexity in installation process
Super strength in receipt of signal
Reasonable structure and low noise amplifier tube to increase the resolution
of image.
360° Rotation
Main Technical Criteria
- Frequency(VHF):40-230MHz
- Frequency(UHF):470-860MHz
- VHF Gain:28-32dB
- UHF Gain:32-36Db
- Impedance:750 F connector
- Max Rotation: Max 360*
- Power:3 W
- Noise Figure: < 2.5Db
- Output Level: 105dBu
- Voltage Input: AC120V 10%60Hz
Feature
- Parabolic focusing reception
- UHF/VHF TV and FM radio
- Super active outdoor antenna
- High quality far ranging reception
- Can operate antenna manually
- With infrared remote control
- Easy to install and operate
- 360* all directional rotation
- Built-in high-gain booster
- Built-in low-noise circuit
Packing List
INSTALLATION
-
Step 1: Assemble 8pcs of directors
-
Step 2: Unfold the antenna VHF dipoles
-
Step 3: Fix the directors by M4*18mm screw
-
Step 4:Unfold the antenna reflectors.
-
Step 5:Fix the motor bolster by M5*25mm bolt.
-
Step 6: Install the RG6 coaxial cable with waterproof cap on the F Connector of the main unit and put on the waterproof cap.
-
Step 7:Install the antenna on the pole
-
Step 8: To prevent the damage of F Connector, reserve RG6 coaxial cable of more than 50cm, and fix it on the pole with cable tie. Important: Ensure the antenna faces the location of the signal tower.
*Antenna pole (Optional)**
Find a convenient outdoor location to mount your antenna, then scan for
channels.
Note: Before final mounting, first test your selected antenna location by scanning for channels. In some instances, you may decide to relocate the antenna for better reception.
Antenna Accessories
Optional 75-ohm coaxial Grounding Block
There are some basic Standard Practices for installing an antenna and cables to get the best signal and have a safe (as possible) and durable installation. Outside antennas must be grounded for safety and reception. Sometimes attic antenna’s are grounded when the cable run is greater than 30 feet. Indoor antennas do not need a ground.
How to install?
You should fix the antenna on a desired position. First, turn on the TV to
search channels and adjust the angle of the antenna until the screen is clear
enough.
How to confirm that the antenna is working properly?
Connect the antenna with power supply, make sure the indicator light lights
on. Then plug the antenna into the tuner of your TV and make sure there are
input signals.
How do you do when your TV signals are not strong?
Check if the antenna is powered normally. the power indicator lights light
on, you should adjust the antenna position and direction for the best
reception, then resource the channels
What if I can not receive a signal with antenna?
Signal strength will vary based on certain variables, such as distance from
the transmitter, hills, buildings, and even tall trees can impact reception,
to check the exact distance from your residence to the nearest transmitters
and getan idea of what to expect in the way of reception go to
antennapoint.com antenna web. org and type in your zip code.
Are all broadcasts now in High Definition?
Answer: Not all digital signals are High Definition. Ensure you digital
receiver is a HD receiver, otherwise, no HD channels can be viewed
How to rotate your antenna?
The antenna will rotate 360 degree until the end then rotate backward
automatically.
- Press to red button, the antenna will start to rotate with clockwise or anti-clockwise.
If you lift your fingers from the button when pressed again it may turn toward any direction.
ANY OTHER QUESTION?
SEND US AN EMAIL WITH DETAIL:
- Your order number
- Your situation or question.
Only supply on Amazon
Contact us:
Email: yeceny@outlook.com
MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>