Einhell TC-VC 1930 A Wet and Dry Vacuum Cleaner Instruction Manual

Einhell TC-VC 1930 A Wet and Dry Vacuum Cleaner

Specifications

• Model: TC-VC 1930 A
• Type: Wet and dry vacuum cleaner
• Power: 23.424.90
• Dimensions: Various, refer to manual for details

Product Usage Instructions

Safety Instructions
Always follow the user manual for safe operation. Make sure to:

• Read and understand all safety instructions.
• Check power consumption and connections.
• Use the vacuum cleaner only in specified conditions.

Assembly
Follow these steps for assembly:

1. Mount the wheels as shown in Figure 5.
2. Attach the handle using a screwdriver.
3. Install the filters properly and ensure they are securely in place.

Operation
Operating the vacuum cleaner:

• Switch position 0: Off, I: Normal operation, AUTO: Automatic operation.
• For wet vacuuming, use the foam filter (16) and ensure it is correctly fitted.
• Connect the suction hose (11) to the appropriate nozzle based on your needs.
• To blow air, connect the hose to the blowing connection (10).

Maintenance
Regular maintenance is essential for optimal performance:

• Clean the filters after each use.
• Refer to the manual for filter cleaning instructions.
• For replacement parts, visit www.Einhell-Service.com.

FAQ

• Q: Can I use the vacuum cleaner without filters?
  A: No, it is essential to always use the filters provided with the vacuum cleaner to prevent damage and maintain efficiency.

• Q: How often should I clean the filters?
  A: It is recommended to clean the filters after each use to ensure optimal performance and longevity of the vacuum cleaner.

• Q: Where can I find replacement parts?
  A: For replacement parts, please visit www.Einhell-Service.com for current prices and information.

Danger!
When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care. Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents which arise due to a failure to follow these instructions and the safety instructions.
Explanation of the symbols used (see Fig. 15)

1. Danger!  Read the operating instructions to reduce the risk of injury.
2. Power input
3. Max. power consumption of the automatic socket-outlet
4. Max. total power consumption

Safety regulations

WARNING!
Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.

• Danger! Read the operating instructions before assembling and using the appliance for the first time.
• Check that the mains voltage is the same as the mains voltage specified on the rating plate.
• Pull out the power plug in the following circumstances: Whenever the appliance is not in use, before opening the appliance and before all cleaning and maintenance work.
• Never clean the appliance with solvents.
• Never pull the plug out of the socket by pulling the cable.
• Never leave the appliance unattended when operational.
• Keep away from children.
• Take care to ensure that the power cable does not get damaged by being run over, crushed, pulled or suchlike.
• Do not use the machine if the power cable is in a less than perfect condition.
• If the power cable has to be replaced, the replacement must comply with the design specifications of the manufacturer. Power cable: H 05 VV – F 3 x 1.5 mm2
• Never vacuum the following: Burning matches, smoldering ash and cigarette butts, combustible, caustic, inflammables or explosive substances, vapor or liquids.
• This appliance is not suitable for vacuuming dust which can be harmful to health.
• Store the appliance in a dry indoor location.
• Never use the appliance if it is damaged.
• Only allow the appliance to be serviced by an authorized after sales service outlet.
• Only use the appliance to carry out work for which has been designed.
• Take extra care when cleaning steps.
• Use only genuine accessories and spare parts.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

 Layout and items supplied

Layout (Fig. 1-3 )

1. Handle
2. On/Off switch (with automatic function for specifi c models)
3. Head
4. Filter cage
5. Safety float valve
6. Mains power cable
7. Buckle, prong
8. end
9. Container
10. Suction hose connection
11. Blow connector
12. Flexible suction hose
13. Suction tube
14. Combination nozzle
15. Castors
16. Pleated fi lter
17. Foam fi lter
18. Fastening screw
19. Crevice nozzle
20. Collection bag
21. Hose holder
22. Automatic socket-outlet for electric tools
23. Electric tool adapter
24. Bag for accessories
25. Accessory mount
26. Water drain screw

Items supplied
Please check that the article is complete as specifi ed in the scope of delivery. If parts are missing, please contact our service center or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating instructions.

• Open the packaging and take out the equipment with care.
• Remove the packaging material and any packaging and/or transportation braces (if available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for transport damage.
• If possible, please keep the packaging until the end of the guarantee period.

Danger!
The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. There is a danger of swallowing or suffocating!

• Suction tube (2x)
• Suction hose
• Combination nozzlea
• Pleated filter
• Foam filter
• Crevice nozzle
• Bag for accessories
• Castors (4x)
• Handle
• Fastening screw (6x)
• Original operating instructions

Proper use

The wet/dry vac is designed for wet and dry vacu-uming using the appropriate fi lter. The equipment is not suitable for the vacuuming of combustible, explosive or harmful substances.
The equipment is to be used only for its prescri-bed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or inju-ries of any kind caused as a result of this.
Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.

 Technical data

• Mains voltage: ………………..220-240 V ~ 50/60 Hz
• Power consumption: ………………………….. 1,500 W
• Max. power consumption of the automatic socket outlet: ……………………………………………… 2,000 W
• Max. total power consumption: …………… 3,500 W
• Tank volume: ……………………………………………30 l
• Sound pressure level LpA ………………….. 78 dB(A)
• Uncertainty KpA ………………………………………2 dB
• Weight: ………………………………………………..6.3 kg

Before starting the equipment
Warning! Before you connect the tool to the power supply make sure that the data on the rating plate is the same as the mains data.
The equipment is allowed to be connected only to a shock-proof socket-outlet.

1. Assembling the equipment
   • Fitting the equipment head (Fig. 6)
   • The equipment head (3) is fastened to the tank (8) by the locking hook (7). To remove the equipment head (3), open the locking hook (7) and take off the equipment head (3). When fitting the equipment head (3), make sure that the locking hook (7) locks into place correctly.
   • Fitting the castors (Fig. 5)
   • Fit the castors (14) as shown in Fig. 5.
   • Fitting the handle (Fig. 4)
   • Use a screwdriver to fi t the handle (1).
2. Fitting the filters
   • Important!
   • Never use the wet/dry vac without a filter. Always make sure that the filters are securely seated!
   • Fitting the foam filter (Fig. 7)
   • For wet vacuuming, slip the supplied foam fi lter (16) over the fi lter basket (Fig. 2/4). The pleated fi lter (15) already fi tted upon delivery is not suitable for wet vacuuming.
   • Fitting the pleated fi lter (Fig. 8)
   • For dry vacuuming, slip the pleated fi lter (Fig. 15) over the fi lter basket (Fig. 2/4). The pleated fi lter (15) is suitable for dry vacuuming only.
   • Fitting the dirt bag (Fig. 9)
   • For vacuuming fi ne dry dirt it is recommended that you also fi t the dirt bag (19). This will ensure that the pleated fi lter (15) does not clog up so quickly and help maintain the vacuuming power. It also makes it easier to dispose of the dust. Slip the dirt bag over the vacuuming hole. The dirt bag is suitable for dry vacuuming only.
3. Fitting the suction hose (Fig. 10-13) Connect the suction hose (11) to the corresponding connector on the wet/dry vac, depending on the application required.
   • Vacuuming
   • Connect the suction hose (11) to the suction hose connector (9).
   • Blowing
   • Connect the suction hose (11) to the blow connector (10).
   • To extend the suction hose (11), the elements which make up the multi part suction tube (12) can be attached to the suction hose (11).
4. Suction nozzles
   • Combination nozzle (Fig. 13)
   • The combination nozzle (13) is for vacuuming solids and liquids over medium to large areas.
   • Crevice nozzle (Fig. 12)
   • The crevice nozzle (18) is designed for vacuuming solids and liquids in corners, edges and other areas that are diffi cult to access.

Operation

1. On/Off switch (Fig. 2/2)
   • Switch position 0: Off
   • Switch position I: Normal mode
   • Switch position AUTO: Automatic mode
2. Dry vacuuming
   • For dry-vacuuming, use the pleated filter (15). In addition, you can also fi t the dirt bag. (See point 5.2)
   • Always make sure that the filters are securely seated!
3. Wet vacuuming
   • For wet vacuuming, use the foam filter (16) (see point 5.2).
   • Check that the filter is securely seated at all times.
   • Water drain screw (Fig. 1)
   • To make the tank (8) easier to empty after wet vacuuming, it is fitted with a water drain screw (25). Open the water drain screw (25) by turning it anti-clockwise and drain the liquid.
   • When wet vacuuming, the floating safety switch (5) closes when the maximum tank level is reached. At the same time, the suction noise of the equipment will change and become louder. You must then switch off the equipment and empty the tank.
   • Danger!
   • The wet/dry vac is not suitable for the vacuuming of combustible liquids. For wet vacuuming, use only the supplied foam filter.
4.  Automatic mode
   • Connect the power cable of your electric tool to the automatic socket-outlet (21) and connect the suction hose (11) to the vacuuming connector of your electric tool. Check that the connections are secure and air-tight.
   • Set the switch (2) on the wet/dry vac to position “AUTO “(automatic mode). The moment you switch on the electric tool, the wet/dry vac will switch on as well. When you switch off the electric tool, the wet/dry vac will switch off as well after a pre-set delay.
5. Blowing
   • Connect the suction hose (11) to the blow connector (10) on the wet/dry vac.

Replacing the power cable

• Danger!
• If the power cable for this equipment is damaged, it must be replaced by the manufacturer or its after-sales service or similarly trained personnel to avoid danger.

Cleaning, maintenance and ordering of spare parts

Danger!
Always pull out the mains power plug before starting any cleaning work.

1. Cleaning

   • Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible.
   •  We recommend that you clean the appliance immediately after you use it.

2. Cleaning the appliance head (3)
   Clean the appliance regularly with a damp cloth and some soft soap. Do not use cleaning agents or solvents; these may be aggressive to the plastic parts in the appliance.

3. Cleaning the container (8)
   The container can be cleaned with a damp cloth and some soft soap or under running water, depending on the amount of dirt.

4. Cleaning the filters

   • Cleaning the pleated filter (15)
   • Clean the pleated filter (15) regularly by carefully patting it and cleaning it with a fine brush or hand brush.
   • Cleaning the foam filter (16)
   • Clean the foam filter (16) with a little soft soap under running water and allow it to air-dry.

5. Maintenance
   There are no parts inside the equipment which require additional maintenance.

6. Ordering replacement parts:
   Please quote the following data when ordering replacement parts:

   • • Type of machine
     • Article number of the machine
     • Identification number of the machine
     • Replacement part number of the part required For our latest prices and information please go to www.Einhell-Service.com

Disposal and recycling
The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask in your local council offices.

Storage

Store the equipment and accessories in a dark and dry place at above freezing temperature. The ideal storage temperature is between 5 and 30 °C. Store the electric tool in its original packaging.

Disposal

• Power tools, rechargeable batteries, accessories and packaging should be sorted for environmental-friendly recycling.
• Do not dispose of power tools and batteries/rechargeable batteries into household waste!
• Only for EU countries:
• According to the Directive 2012/19/EU on waste electrical and electronic equipment and its transposition into national law, power tools that are no longer usable, and, according to the Directive 2006/66/EC, defective or drained batteries must be collected separately and disposed of in an environmentally correct manner.
• If disposed incorrectly, waste electrical and electronic equipment may have harmful effects on the environment and human health, due to the potential presence of hazardous substances.
• Only for United Kingdom:
• According to The Waste Electrical and Electronic Equipment Regulations 2013 (SI 2013/3113) (as amended) and the Waste Batteries and Accumulators Regulations 2009 (SI 2009/890) (as amended), products that are no longer usable must be collected separately and disposed of in an environmentally friendly manner.
• The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of the Einhell Germany AG.
• Subject to technical changes

Service information

• We have competent service partners in all countries named on the guarantee certificate whose contact details can also be found on the guarantee certificate. These partners will help you with all service requests such as repairs, spare and wearing part orders or the purchase of consumables.
• Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables.

tool adapter, etc.
Consumables*| Pleated filter, foam filter, dirt bag, additional filter, etc.
Missing parts|

Not necessarily included in the scope of delivery!
In the eff ect of defects or faults, please register the problem on the internet at www.Einhell-Service.com. Please ensure that you provide a precise description of the problem and answer the following questions in all cases:

• Did the equipment work at all or was it defective from the beginning?
• Did you notice anything (symptom or defect) prior to the failure?
• What malfunction does the equipment have in your opinion (main symptom)?Describe this malfunction.

Warranty certificate

Dear Customer,
All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that this equipment develops a fault, please contact our service department at the address shown on this guarantee card. You can also contact us by telephone using the service number shown. Please note the following terms under which guarantee claims can be made:

1. These guarantee terms apply solely to consumers, i.e. natural persons, who do not want to use this product in connection with either their commercial or other self-employed activities. These guarantee terms regulate additional guarantee services which the undermentioned manufacturer promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory rights of guarantee are not aff ected by this guarantee. Our guarantee is free of charge to you.

2. The guarantee services cover only defects due to material or manufacturing faults on the new product which you have bought in the European Union from the undermentioned manufacturer and are limited to either the rectification of said defects or the replacement of the product, whichever we prefer. Please note that only equipment under the brand name “Professional” has been designed for use in commercial, trade or professional applications. For all other products the guarantee is invalidated if the equipment is used within the guarantee period in commercial, trade or industrial applications or for other equivalent activities.

3. Our guarantee does not cover:

   • Damage to the equipment caused by failure to comply with the installation/assembly instructions or by unprofessional installation; damage caused by failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or current type); damage caused by failure to comply with the maintenance and safety regulations; damage caused by exposing the equipment to abnormal environmental conditions; damage resulting from poor care and maintenance.
     Damage to the equipment caused by misuse or incorrect applications (e.g. overloading the equipment or using non-approved attachments or accessories); damage caused by foreign bodies (e.g. sand, stones, dust, ….) getting inside the equipment. Damage in transit; damage caused by force or external influences (e.g. by dropping the equipment).

   • Damage to the equipment or parts of the equipment which is owed to use-related, normal or otherwise natural wear. For example, batteries and battery packs are manufactured with a cycle limit for design related reasons. Wear is negatively influenced in particular by load demands and charging speeds as well as exposure to heat, cold, vibration and impact.

4. The guarantee is valid for a period of 2 years starting from the purchase date of the equipment. Guarantee claims must be submitted before the end of the guarantee period and within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the equipment even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or for any replacement parts fitted. This also applies if on-site service is used.

5. To assert your guarantee claim, register the defective equipment at: www.Einhell-Service.com. You will need to provide proof of purchase of the new item of equipment. Equipment returned without such proof or without a rating plate are excluded from the guarantee services because of the lack of traceability. If the defect is covered by our guarantee, then either the item in question will be repaired immediately and returned to you or we will send you a new replacement.

6. If you have taken the equipment with you to a diff erent EU country than where you bought it, we will arrange for a local service partner to provide the guarantee services. If you take the equipment outside the EU, the guarantee will not apply.

Of course, we are also happy to off er a chargeable repair service for any defects which are not covered or no longer covered by the scope of this guarantee. To take advantage of this service, please send the equipment to our service address. We draw attention to the restrictions of this guarantee concerning wear parts, consumables and missing parts as presented in the service information included in this operating manual.
Warrantor/ Service:
Einhell UK Ltd, Unit 10, 1st Floor, Champion‘s Business Park, Arrowe Brook Road, Upton, Wirral, CH49 0UQ

• Declaration of conformity: We declare conformity in accordance with the EU directive and standards for article

• Standard references: EN 60335-1; EN 60335-2-2; EN 62233;

• EN IEC 55014-1; EN IEC 55014-2; EN IEC 61000-3-2; EN 61000-3-3

• Einhell Germany AG · Wiesenweg 22 · D-94405 Landau/Isar

• Landau/Isar, den 02.10.2023

• • GB Wet and dry vacuum cleaner

Declaration of conformity

• We, Einhell UK Ltd
• Champions Business Park, First Floor Unit 10, Arrowe Brook Rd, Upton, Wirral CH49 0AB,
• United Kingdom declare the conformity to UK standards and legislation was assessed for:
• Wet and dry vacuum cleaner TC-VC 1930 A (Einhell)
• Standards: BS EN 60335-1; BS EN 60335-2-2; BS EN 62233;
• BS EN IEC 55014-1; BS EN IEC 55014-2; BS EN IEC 61000-3-2; BS EN 61000-3-3

References

• Einhell Service
• Service.com is for sale | www.brandforce.com
• Einhell Service
• Herramientas de alta calidad para aficionados al bricolaje y la jardinería | Einhell.es
• Strumenti di alta qualità per gli amanti del Fai da Te e del giardinaggio | Einhell.it

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>