Kunli Fan Remote Controller Instruction Manual
- August 17, 2024
- Kunli
Table of Contents
Kunli Fan Remote Controller
Product Specifications
- Product Name: Fan Remote Controller
- Model: KLJSQ4001
- Frequency: 315MHz
- Power Source: 23A 12V battery
- Country of Origin : China
Product Usage Instructions
Installation:
- Turn off the power supply.
- Connect the ceiling fan wires according to the manual.
- Turn on the power switch.
- Long press the OFF key on the remote for code matching.
- When you hear a BEEP sound from the receiver, it indicates successful code matching.
- In case of code matching failure, repeat the above steps.
Operating Instructions:
- Lights Control: Press the (light) key to turn on/off the lights. Long press to adjust brightness.
- Fan Speed Control: Use the + and – buttons to adjust fan speed – Growth rate for higher speed and Moderate for lower speed.
- Reversible Function: Press the (Reversible) key to change the fan direction.
FAQ
-
What should I do if the remote is not working?
If the remote is not working, check the battery and ensure it is inserted correctly. If issues persist, refer to troubleshooting in the manual. -
Can I use this remote with any type of ceiling fan?
The remote is designed for use with compatible ceiling fans. Make sure to check the product compatibility before installation. -
How do I know if the code matching was successful?
A successful code match is indicated by a BEEP sound from the receiver. If you don’t hear the sound, repeat the code matching process.
INTRODUCTION
- This unit is mainly for fan and its lighting function.
- This product has an FCC ID certificate. Adopted frequency:315MHz.
- Please turn off the power first, then refer to the manual for installation instruction.
Setting up the remote
-
The wireless control is designed to operate both the light and speed of the fan. The remote uses a 23A 12V battery. Remove the remote’s back cover and insert the battery.
-
Please make sure the battery is inserted in the right direction or the remote may not function.
-
The installation direction of the battery is shown in the battery identification on the back of the remote control, and the negative pole of the battery is installed towards the spring end. If the keystroke indicator does not light, it means that the battery direction is wrong or the battery has no power.
-
Connect the ceiling fan wire.turn on the power switch and long press the “OFF” key for code matching. when the receiver makes a “ BEEP ” sound.it indicates that the codes are successfully matched.
In case of code matching failure,turn off the power and repeat the above operations. -
Remove the battery from the remote if you do not plan to use the remote for a long time.
Operating instructions
- Turn on power and press (light) key on the remote to turn on the lights. Press the key again to turn off. Press this key for a long time to turn the light to the brightest or darkest.
- (Two speed buttons) These are the two keys for adjusting fan speed.Press + Growth rate.press – Moderate
- Press ( Reversible) to turn on the direction . Press it again to reversal
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference
- This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
FCC Radiation Exposure Statement:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
ISED Statement
- This device complies with Industry Canada license-exempt RSS standard(s).
- Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
- The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
- This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
- This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.
- This equipment should be installed and operated distance between the radiator & your bodywithout restriction.