SCIWIL SW-G518 E-Bike Display User Guide
- August 15, 2024
- SCIWIL
Table of Contents
SCIWIL SW-G518 E-Bike Display
Safety Notes
PLEASE TAKE CAUTION WHEN USE, DO NOT PLUG OR UNPLUG THE DISPLAY WHILE YOUR E-BlKE IS POWERED ON.
- AVOID CLASHES OR BUMPS TO THE DISPLAY.
- AVOID USING IN HEAVY RAINS, SNOWS OR LONG EXPOSURE TO STRONG SUNLIGHT. DO NOT TEAR THE WATER-PROOF FILM ON THE SURFACE OF THE SCREEN, OTHERWISE THE WATER-TIGHT PERFORMANCE OF THE PRODUCT MAY BE DEGRADED.
- DO NOT PLUG OR UNPLUG THE DISPLAY WHILE THE SYSTEM IS POWERED ON. UNAUTHORIZED ADJUSTMENT TO DEFAULT SETTINGS IS NOT SUGGESTED, OTHERWISE NORMAL USE OF YOUR E-BIKE CAN NOT BE GUARANTEED.
- WHEN THE DISPLAY PRODUCT DOES NOT WORK PROPERLY1 PLEASE SEND THE IT FOR AUTHORIZED REPAIR IN TIME.
Overview
-
Product Name and Model
Product Name: E-Bike Display
Product Model: SW’-G518 -
Product Introduction
SW-G518 features high-brightness anti-glare color LCD and minimalist interface, working as an ideal HMI solution for EN15194 electric bikes. -
Specifications
- Working Voltage: DC 24V/36V/48V/60V/72V
- Rated Working Currer:it: 12mA
- Leakage current: <luA
- Screen Size: 2.3″ LCD
- Communication Type: UART (by default)/ CAN (optional)
- Optional Functions: Bluetooth, NFC
- Working Temperature: -20°C ~ 60°C
- Storage Temperature: -30°C ~ 70°C
- Waterproof Rating: IP65
-
Function
- Boot password
- System unit switE: h (km/h or mph)
- Assist Level Control and Display
- Battery indication: battery level percentage, low voltage indication
- Speed display: (in km/h or mph) real-time speed (SPEED), max speed (MAX)r average speed (AVG)
- Distance: single-trip distance (TRIP), total travel distance (ODO)
- Assist Mode Control and Display (3/5/9 levels)
- Walk assist mode
- Front light indication: front light status supported by controller.
- Error code indication
- Riding Info: Braking Status, Front Li~1ht Status, Cruise, Low Voltage.
- Turning Signals: This function works with controller.
- Dual Drive Control and Display: This function works with controller.
- Status of Double Battery Packs: optional, works with controller.
- NFC Function: optional.
- Bluetooth Connection: optional, support OTA upgrade via mobile phone.
-
**Size
**
- Assembly
- Open the holder ring/ rubber spacer of the display and fix the display on the handlebar, adjust it to a proper facing angle. Use a M4 Hex Wrench to fix and tighten the screws. Standard fixing torque: 1N·m.
-
Damage due to excessive fixing torque is not covered by warranty.
- Open the holder ring/rubber spacer of the keypad and fix it on the handlebar, adjust it to a proper facing angle. Use a M3 Hex Wrench to fix and tighten the screws. Standard fixing torque: 1N·m.
-
Damage due to excessive fixing torque is not covered by warranty. 3. Plug the 5-pin connector of the display to the coupling connector of the Controller. 7. Seria I Code
Example:
111: Customer Code
22: Protocol Code
333333: P.O. Date (YYMMDD)
555: Order Receiving Number
6666: Production Date (YYMM)
Operation
Display Interface
- Riding Interface
- Status: Real-time Riding Status: Bluetooth, Front Light, Brake, Low Voltage, Turning, Cruise, Drive Status, etc.
- Battery Statu s: Residual Battery Percentage
- Multi- Function Section: ODO (total range), TRIP (single ride range), MAX (max . speed)r AVG (average speed), TIME (riding time), VOL (battery voltage), Wh (mot or power), CUR (current), etc.
- Assist Level Mode: 3/5/9 Levels available.
Setting Interface
In the above interface: Setting Item: P01, Parameter Value: 02
Error Interface
In the above interface: Error Indicator: ERROR, Error Code: E10
Key Pad
SWK2 Keypad Illustration:
There are 5 keys on the SWK2 keypad, in the following instructions:
is called Plus Key;
is called On/ Off Key;
is called Minus/Walk Assist Key Key;
Key Operation
Key operation guide as follows:
Press and Hold: means press and hold the key(s) for more than 2s.
Press: means press the key(s) for less than 0.Ss.
-
On/Off
Turn on the Display: When the display is off, press and hold the On/ Off Key to turn on the display, it will show boot interface and then enter riding interface. (If boot password i$ activated, enter the boot password at start) .
Turn off the Display: When the display is on, press and hold the On/ Off Key, the display will be turned off. If no operation is engaged for 10min (0km/ h), the display will be auto-off. Auto-off time can be set in the Settings. -
Assist Level
Press the Plus Key or Minus/ Walk Key to switch assist levels. There are 5 levels by default: 0/ 1/ 2/3/4/5. 0 means no assist power. -
Toggle Displays
When the display is on, press the On/Off Key to toggle among ODO (total range), Trip (single trip range), TIME (riding time) etc. -
Light On/Off
Turn on the Front Light: when the. front light is off, press and hold the
Plus Key to turn it on; and the light icon will be shown on the riding interface (to remove th is functions, please reconfigure the controller).
Turn off the Front Light: when the front light is on, press and hold the Plus Key to turn it off, and the light icon wfll be off on the riding interface. -
Walk Assist Mode
Engage Walk Assist Mode: On the riding interface, press and hold the Minus/Walk Key to enter walk assist mode. Hold the Minus/ Walk Key to engage walk assist mode, the walk mode icon will be shown on the riding interface, the real-time speed will be shown in the speed section .
Disengage Walk Assist Mode: release the Minus/Walk Key to disengage the walk assist mode, the icon will off on the riding interface.
Settings
-
Setting Operations
-
Enter the Settings: when the display is on, press and hold the Up Key and the Down Key together to enter the Settings. Av ailable setting items include: system voltage, wheel size (inch), magnetic steel number for speed gauge, speed limit etc (please refer to 4.2 Setting Items) .
-
Adjust Settings: on the Settings interface, press the Up Key or the Down Key to set values for items. The value will blink after change. Press the Mode Key to save the set value and switch to next item.
-
Save and Exit Settings: press and hold again the Up Key and the Down Key together to exit the Settings and save the set value. The system will save and exit automatically if there’s no operation for 10s.
-
Setting Items
-
POD: Factory Reset: opti’onal ..
-
P01: Backlight Brightness. 1: darkest; 3: brightest.
-
P02: System Unit. O: km (metric); 1: mile (imperial) .
-
P03:System Voltage: 24V/ 36V/ 48V/ 60V/72V.
-
P04: Auto-Off Time
0: never; other value means auto-off time intervaL Unit: minute -
POS: Pedal Assist Level
-
0-3 Level Mode; 1-3 Level Mode (no Level0)
-
0-5 Level Mode; 1-5 Level Mede (no Level0)
-
0-9 Level Mode; 1-9 Level Mode (no Level0)
-
P06: Wheel Size. Unit: inch; Increment: 0.1.
-
P07: Motor Magnets Number for Speed Gauge. Range: 1-100
POS: Speed Limit. Range: 0-100km/ , communications status (controller controlled) -
The max speed will be kept constant at the set value.
Error Value: ±1km/ h (applicable to both the PAS/ throttle mode)
Note: The above-mentioned values are measured by metric unit (km/ h).
When the system unit is set to imperial unit (mph), the speed displayed will be automatically switched to corresponding value in imperial unit, however the speed limit value in the imperial unit interface won’t change accordingly. -
P09: Direct Start/ Kick-to-Start
-
0: Direct Start (Throttle-on-demand)~
-
1: Kick-to-Start
-
P10: Drive Mode Setting
-
0: Pedal Assist – The pedal assist level decides the motor power output. In this status the throttle does not work.
-
1: Electric Drive – Thee-bike is only controlled by the throttle. In this status the pedal assist does not work.
-
2: Pedal Assist + Electric Drive (electric drive does not work in directstart status)
-
P11: Pedal Assist Sensitivity. Range: 1-24.
-
P12.: Pedal Assist Starting Intensity. Range: 0-5.
-
P13: Magnets Number in Pedal Assist Sensor. 3 Types: 5/8/12pcs.
-
P14: Current Limit Val.ue. By default: 12A. Range: 1-20A.
-
P15: Display Low Voltage Value.
-
P16: ODO Clearance. Press and hold the Up l<ey for Ss and ODO value will be cleared.
-
P17: Cruise. 0: cruise function deactivated, 1: cruise function activated.
-
Error Code
Error Code (decimal) | Status | Note |
---|---|---|
E00 | Normal | |
E01 | Reserved | |
E02 | Brake Error | |
E03 | PAS Sensor Error (Riding Mark) | Not Realized |
E04 | Walk Assist Mode | |
E0S | Real-Time Cruise | |
E06 | Low Voltage Protection | |
E07 | Motor Error | |
E08 | Throttle Error | |
E09 | Controller Error | |
E10 | Communications Error | |
E12 | BMS Communications Error | |
E13 | Front Light Error |
Connection
Pin No. | Wire Color | Functions |
---|---|---|
1 | Red (VCC) | Display Power Wire |
2 | Blue (K) | Electric Lock Wire |
3 | Black (GND) | Display Ground Wire |
4 | Green (RX) | Display Data Receiving Wire |
5 | Yellow (TX) | Display Data Sending Wire, |
Extended Functions- Front Light:
Brown (DD): The power wire ( +) of the light
White (GND).: The ground wire ( ~) of the light.
Note: For waterproof connectors, wire .sequences are concealed.
Warranty
In compliance with local laws, Scowl provides limited warranty period covering 24 months after the date of manufacturing (as indicated by the serial number), applies to quality issues during normal operations.
The limited warranty shall not be transferred to a third. party other than as specified in the agreement with Scowl
Warranty Exclusions:
- Scowl products that have been opened: I, modified or repaired without authorization.
- Damage on the connectors.
- Damage to the surface after leaving factory, including shell1 screen, buttons, or other appearance parts.
- Damage to wiring and cables after leaving factory, including breaks. and exterior scratch.
- Damage or loss due to force majeure (e.g. fire or earthquake) or natural disaster (e.g. lightening).
- Out of the warranty peri0d.
Version
This display user manual is in compliance with the general software version (NO) of Changzhou S.ciwil E-Mobility Technology Co .. , Ltd. There are chances that display products 9n some e-bikes may have a different software version , which is subject to the actual versi0n .in use ..
E-Bike Display
Model: SW-G518
Protocol: Lithium II
Version: V6.03
Scan QR Code to Download PDF
Changzhou Sciwil E-Mobility Technology Co., Ltd.
Documents / Resources
|
SCIWIL SW-G518 E-Bike
Display
[pdf] User Guide
SW-G518 E-Bike Display, SW-G518, E-Bike Display, Display
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>