tacautoparts #123300O Viewpoint Running Boards Installation Guide
- August 12, 2024
- tacautoparts
Table of Contents
tacautoparts #123300O Viewpoint Running Boards
INSTALLATION INSTRUCTIONS
Viewpoint Running Boards 2021-2024 Jeep Grand Cherokee L 2022-2024 Jeep Grand Cherokee (Excl. 2022-2024 4xe Models) PART#123300
PARTS LIST
| 1 | Driver/Left Running Board | 1 | 10mm x 40mm Hex Bolt |
|---|---|---|---|
| 1 | Passenger/Right Running Board | 3 | 10mm Lock Washers |
| 1 | Driver/Left Front Mounting Bracket | 3 | 10mm x 30mm OD x 2.5mm Flat Washers |
| 1 | Passenger/Right Front Mounting Bracket | 1 | 10mm x 27mm OD x 3mm Flat Washer |
| 1 | Driver/Left Center Mounting Bracket | 1 | 10mm Hex Nut |
| 1 | Passenger/Right Center Mounting Bracket | 1 | 10mm Threaded Insert |
| 1 | Driver/Left Rear Mounting Bracket | 1 | 10mm Insert Tool |
| 1 | Passenger/Right Rear Mounting Bracket | 6 | 6mm x 30mm Hex Bolts |
| 3 | 12mm x 50mm Hex Bolts | 12 | 6mm x 18mm OD x 1.6mm Flat Washers |
| 3 | 12mm Lock Washers | 6 | 6mm Lock Washers |
| 3 | 12mm x 32mm OD x 3mm Flat Washers | 6 | 6mm Hex Nuts |
| 3 | 10mm x 50mm Hex Bolts |
PROCEDURE
- REMOVE CONTENTS FROM THE BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. USE ILLUSTRATION TO IDENTIFY BRACKETS AND TYGER FURY STEPS.
- Starting on the Driver/Left front of the vehicle, remove the cover on the bottom car. Select the Driver/Left Front Mounting Bracket. Attach the Mounting Bracket to the threaded insert in the front location with (1) 12mm Hex Bolt, (1) 12mm Lock Washer, and (1) 12mm Flat Washer, (Figures 1 & 2). Do not tighten the hardware.
- Attach the Mounting Bracket to the pinch trim with (1) 6mm Bolt Plate, (1) 6mm Flat Washer, (1) 6mm Lock Washer, and (1) 6mm Hex Nut, (Figure 3). Do not tighten the hardware.
- Move along the body panel to the center mounting location, (Figure 4). Select the Drier/Left Center Mounting Bracket. Repeat Step 2 to install the Bracket, (Figures 3 & 4). Do not tighten the hardware.
- Continue to the rear mounting location in front of the rear tire, (Figure 5). Select the Driver/Left Rear Mounting Bracket. Attach the Bracket to the threaded insert with (1) 10mm Hex Bolt, (1) 10mm Lock Washer, and (1) 10mm Flat Washer, (Figures 5 & 6). Do not tighten the hardware. Repeat Step 3 to attach the Bracket to the pinch trim.
- Select the Driver/Left Viewpoint Running Board. Insert (6) T-Bolts into the channels at the bottom of the Running Board, (3) per channel, (Figure 7). Place the Running Board onto the Mounting Brackets and line up the T-Bolts. Attach the Running Board to the Mounting Brackets with (6) 6mm Flat Washers, (6) 6mm Lock Washers, and (6) 6mm Hex Nuts, (Figure 8). Do not tighten the hardware.
- Level and adjust the Running Board and tighten all hardware.
- Move to the Passenger/Right side. Repeat Steps 1,2 & 5 to attach the Passenger/Right Front and Rear Mounting Brackets.
- Locate the center mounting location, (Figure 9). Select the Passenger/Right Center Mounting Bracket. Hold the Bracket and line up to the hole in the pinch trim to the lower slot in the top of the Bracket. Mark where the top slot is located on the floor panel. Using a 1/2” drill bit, (not included) to drill through only the bottom layer of the floor panel.
- Select the 10mm Threaded Insert and the 10mm Insert Tool. Push the Tool and Insert the assembly into the factory hole. NOTE: If the Insert fits too tight, lightly tap it into place with a small hammer.
- Firmly hold the handle on the Tool and tighten the hex bolt in the Insert until it is fully collapsed and locked in place, (Figures 10 & 11). NOTE: Do not over-tighten the Insert or a pull-out may occur. Once the Insert is collapsed, remove the tool from the Insert.
- Attach the Passenger/Right Center Mounting Bracket to the Threaded insert with (1) 10mm Hex Bolt, (1) 10mm Lock Washer, and (1) 10mm Flat Washer. Do not tighten the hardware. Repeat Step 3 to attach the Bracket to the pinch trim.
- Repeat Steps 6 & 7 to attach the Passenger/Right Running Board. Do not tighten the hardware.
- Level and adjust the Running Board and tighten all hardware.
- Do periodic inspections of the installation to make sure that all hardware is secure and tight.
To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Running Boards.
Driver Side Installation Pictured
Passenger Side Installation Pictured
- (Fig 9) Locate the Passenger/Right center mounting location. Line up the top of the Passenger/Right Center Mounting Bracket to the hole in the pinch trim. Mark the top slot for drilling. Use a 1/2” drill bit, not included
- (10-A) Select Insert Tool and (1) Insert. Thread Insert onto the end of Insert Tool. Hand tighten only, do not tighten the hex bolt
- (10-B) Firmly hold the assembly and push Insert into the drilled hole.
- (10-C) Hold the Tool Assembly up tight in the body panel. Turn the hex bolt in the Tool clockwise to expand the insert in the body panel. Remove the Tool once the Insert is fully tightened. Do not overtighten or Insert may be damaged.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>