SUNTEC HB200 Wireless Bluetooth Remote Control User Manual
- August 7, 2024
- SUNTEC
Table of Contents
SUNTEC HB200 Wireless Bluetooth Remote Control
Specifications
- Operation temperature: 20% to 80% non-condensing
- Storage temperature: 20% to 80% non-condensing
- Relative humidity: 700 to 1060 hPa
- Approvals: IEC 60601-1, IEC 60601-1-6, IEC 60601-1-2, ANSI/AAMI ES60601-1, CSA CAN/CSA-C22.2 NO. 60601-1, RED 2014/53/EU, FCC Part 15.249, IC RSS247, Telec MIC
- Compatibility: All OpenBusTM BLE control boxes
- Magnet key ordering no.: 0858008 (RAL 7035 light grey)
- Battery cover ordering no.: SA1031W9012
Product Usage Instructions
Pairing Bluetooth devices
- Enter pairing mode.
- Move the hand control closer to the control box you want to pair with.
- Pair the hand control with the control box.
Entering Pairing Mode
When in pairing mode, the control box buzzer will beep, and the LED will
blink. Place the magnet key over the Hall ( ) and press down for 3 seconds to
enter pairing mode.
Connecting to the control box
When the hand control LED blinks fast and the control box gives a high
frequency sound at the same speed, press down key on the hand control to
finalize pairing.
Programming of Memory Buttons:
Press Buttons 1+2 for 1 sec, release, then press 1 until 2 beeps are heard
to set Memory 1. Repeat the procedure for Memory 2.
Functionality – Locking
To lock using the magnet, hold it over the marking ( ) and press down key
number. To unlock, use the magnet key and press up key.
Recommendations
Follow the user manual for detailed instructions on usage and maintenance
of the product.
FAQ
-
Q: Can I order extra battery covers for the HB200?
A: Yes, it is possible to order extra battery covers for the HB200. The ordering number is SA1031W9012. -
Q: How do I pair a SUNTEC control directly to a SUNTEC control box that supports BLE?
A: To pair directly, enter pairing mode, move the hand control closer to the control box, and then follow the pairing steps as mentioned in the user manual.
Controls User Manual
SUNTEC ApS – Østergade 33 – 3200 Helsinge – Denmark www.suntec.dk
HB200
The HB200 Wireless is a Bluetooth® Low Energy (BLE) hand control for
medical treatment chairs. LED light will function as pairing and battery
indicator.
Usage
- Operation +5 °C to + 40 °C
- temperature: Storage -10 °C to + 50 °C
- temperature: Relative 20% to 80% non-condensing
- humidity: Operation +5 °C to + 40 °C
- temperature: Storage -10 °C to + 50 °C
- temperature: Relative 20% to 80% non-condensing
- humidity: Atmospheric 700 to 1060 hPa
- pressure: Approvals:
- IEC 60601-1
- IEC 60601-1-6
- IEC 60601-1-2
- ANSI/AAMI ES60601-1
- CSA CAN/CSA-C22.2 NO.
- 60601-1 RED 2014/53/EU
- FCC Part 15.249
- IC RSS247
- Telec MIC.
- Compatibility: All OpenBusTM BLE control boxes
Magnet key
Magnet key – ordering no. 0858008 (RAL 7035 light grey)
Battery
The battery in the HB200 is a standard CR2032 coin cell battery.
Battery lifetime
With a usage of 140 sec/day, the HB200 will last approximately two years.
Changing the battery
To change the HB200 battery, open the battery cover on the back using a coin
or a similar tool to turn the arrow counterclockwise from the locked state to
the unlocked state.
- Low battery indication – When the battery power level falls below 20%, the LED will flash 4 times when a key is pressed.
- New battery indication – When the battery has been changed, the LED will be lit for 4 seconds after the first keypress.
Battery cover
It is possible to order extra battery covers. Battery cover ordering no.
SA1031W9012
Pairing Bluetooth devices
Direct pairing. Direct pairing is used for pairing a SUNTEC control directly to a SUNTEC control box that supports BLE.
- Enter pairing mode
- Move the hand control closer to the control box you want to pair with
- Pair the hand control with the control box
Entering Pairing Mode
In pairing mode, the light/sound frequency will increase when the HB200 gets closer to a control box.
Connecting to the control box
When the hand control LED is blinking fast and the control box gives a high
frequency sound in the same speed, the devices are ready for pairing. To
finalise the pairing, press down key on the hand control.
Programming of memory
Buttons 1+2 are pressed for 1 sec.
Then release and press 1 until 2 beeps are heard. Memory 1 is now set. Same
procedure repeated for memory 2.
Functionality
Locking
Locking is possible with the magnet and pressing a key on the remote control.
To lock with magnet: hold the magnet key over the marking ( ) and press down
key number
To unlock use the magnet key and press up key.
Recommendations
- Do not submerge the hand control in water.
- Unless otherwise specified or agreed with SUNTEC, the hand control is only intended to be used for SUNTEC/LINAK systems.
- It is recommended to check the hand control for damage and holes caused by violent handling before washing the application or at least once a year.
- Always perform the pairing of hand control and control box in close proximity to the application. Also ensure that the pairing has been made with the correct application by operating the application after ended pairing.
- When intending to operate an application with LINAK BLE, please ensure that the correct BLE hand control is used. Otherwise, there is a risk of unintended movement of the application that has been paired with the BLE hand control.
- When changing the battery, the battery cover must be lubricated with technical white Vaseline for easy mounting and to avoid fluids from entering the hand control.
- The string attachment hole must not be used as a magnet key placeholder. The HB200 locking mode can be activated by the magnet key both on the front and the back of the hand control resulting in unavailable drive functions.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>