TEKBOX TBS-200K500 50 omega High Power VSWR Bridge User Guide
- August 6, 2024
- TEKBOX
Table of Contents
TEKBOX TBS-200K500 50 omega High Power VSWR Bridge
Specifications
- Characterized frequency range: 200 kHz to 500 MHz
- Directivity: > 20 dB
- Coupling: < 0.3 dB
- Operating temperature range: Not specified
- Impedance: 50 Ohms
- Port matching: < 0.7 dB
- RF connectors, through ports: Not specified
- RF connectors, coupling ports: Not specified
- Max. power handling: 100W
- Output shorted or open power handling: Max. 35W
- Dimensions: Not specified
- Weight: Not specified
Product Usage Instructions
Installation
Ensure the VSWR bridge is connected in line with the RF setup according to the
desired measurement configuration.
Power Measurement
The VSWR bridge allows for inline RF power measurements up to 100W. Ensure
proper power handling procedures are followed.
Frequency Range
The bridge is characterized for use in the frequency range from 200 kHz to 500
MHz. Ensure your application falls within this range for accurate
measurements.
Directivity Adjustment
The ports Input/Output and Forward/Reflected can be exchanged,but note that
directivity may slightly deviate from the specified values.
Introduction
The TBSWR-200K500 high power VSWR – bridge is designed for forward / reverse power measurement in EMC immunity test setups with BCI probes (Substitution Method) and general high power applications in the HF and VHF range. The bridge combines the wide frequency range and directivity of a directional bridge and the low insertion loss and power handling capability of a directional coupler.
The TBSWR-200K500 is characterized in the frequency range from 200 kHz to 500 MHz. The high power handling capability of up to 100W allows inline RF power measurements, and a variety of other applications. The insertion loss over the frequency range is typically between 0.2 and 0.7 dB, which is significantly smaller than the average 7 dB associated with VSWR – bridges.
Typical data
Characterized frequency range: 200 kHz – 500 MHz
Directivity: 200 kHz – 500 MHz| > 20 dB| Coupling:| 200 kHz – 300 MHz|
-40 dB ± 0.3 dB
---|---|---|---|---
800 kHz – 50 MHz| > 30 dB| | 300 MHz – 500 MHz| -40 dB ± 1 dB
Insertion loss: 200 kHz – 200 MHz| < 0.3 dB| Max. power:| 200 kHz – 200 MHz|
100 W CW )
---|---|---|---|---
200 MHz – 500 MHz| < 0.7 dB| | 200 MHz – 500 MHz| 70 W CW )
| | *) Short time (max. 1 minute): 150 W
| | Output shorted or open: max. 35 W
Operating temperature range:| – 20 °C to + 40 °C|
Impedance:| 50 Ω|
Port matching:| > 20 dB|
RF connectors, through ports:| N-female|
RF connectors, coupling ports:| SMA-female|
Dimensions:| 113 mm x 60 mm x 35 mm|
Weight:| 290 g|
Measurement Plots
Operating principle
The ports Input/Output and Forward/Reflected can be exchanged. However, directivity may deviate slightly from the specified values.
Mechanical Drawing
Ordering Information
| Part Number | Description |
|---|---|
| TBSWR-200K500 | VSWR – Bridge, 200 kHz – 500 MHz, 100 W; wooden box, 2 pcs SMA |
terminations
History
| Version | Date | Author | Changes |
|---|---|---|---|
| V1.0 | 20.11.2023 | Mayerhofer | Creation of the document |
TekBox Digital Solutions Vietnam Pte. Ltd.
Factory 4, F4, Lot I-3B-1, Saigon Hi-Tech Park, Tan Phu Ward, District 9, Ho
Chi Minh City, Vietnam
FAQ
Q: What is the maximum power handling of the TBSWR-200K500 VSWR Bridge?
A: The TBSWR-200K500 can handle up to 100W for inline RF power
measurements and a maximum of 35W for output shorted or open configurations.
Q: What is the typical insertion loss of the VSWR Bridge over its frequency
range?
A: The insertion loss of the bridge typically ranges between 0.2 and 0.7
dB, which is significantly lower than the average 7 dB associated with VSWR
bridges.
Q: Can the directivity of the VSWR Bridge be adjusted?
A: The ports Input/Output and Forward/Reflected can be exchanged,
allowing for adjustments, but directivity may deviate slightly from the
specified values.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>