mAX PEEDING RODS AAPDIPEI-VLC Air Controller Kit Installation Guide
- August 6, 2024
- mAX PEEDING RODS
Table of Contents
Since 2006
AIR CONTROLLER KIT
INSTALLATION GUIDE
UNIVERSAL
FIT FOR MOST 1/2, 3/4
AND 1TON PICKUPS AND VANS
AIR SPRING LEVELING ELECTRIC CONTROLLER KIT
PACKING LIST
Main parts
1|
| 1X 12V Air
compressor| | | 1X Gauge
panel| 3| | 1X Air Line
φ*1 (6M)
---|---|---|---|---|---|---|---|---
4| | 1X Wire harness
(2.5M) black| 5| | 1X Wire
harness (8.5M) red| 6| | 1X Fuse
harness
(IM)
Hardware kits
7| | 3X T fittin
(stainless)| 8| | 4X Hex screw
M6.325| 9| | 4X Hex
Drill Screw
M4.213
---|---|---|---|---|---|---|---|---
10| | 1X Fuse
adapter a| 11| | 1X Fuse adapter b| 12| | 1X Fuse
adapter c
13| | X T-connector| 14| | 1X Red ring terminal| 15| | 1X Black ring
terminal
16| | X Pre-insulated
wire terminal| 17| | 4X Fully
Insulated wire terminal| 18| | 3X RV wire
terminal (Red)
19| | 1X RV wire
terminal (Black)| 20| | 6X Zip tie
(190*5)| 21| | 4X Air
compressor cushion
(Optional)
22| | 1X Air line cutter| 23| | 1X Car
sticker| | |
PRE-INSTALLATION NOTICE
- This product will not increase the load capacity of your vehicle.
- Do not exceed the manufacturer’s recommended weight limit.
- The installation process may require drilling, professional installation is recommended to ensure personal safety.
- All modifications must be performed by qualified personnel and in compliance with your local modification regulations.
INSTALLATION OVERVIEW
The air spring controller kit is designed to pressurize and depressurize the air springs installed in your vehicle with one button without leaving the cab, bringing great convenience. Moreover, it is a universal kit and suitable for most light or medium duty pickups and vans.
INSTALLATION DIAGRAM
INSTALLING THE GAUGE PANEL
The gauge panel is usually installed under the dashboard in the cab. You may need to drill two holes for installation.
INSTALLING THE COMPRESSOR
Install the compressor at the selected location (i.e. the frame rail on the driver’s or passenger’s side.) and fix it on the vehicle with screws.
NOTE:
Before drilling, please make sure the length of the required air line and
wiring harness is sufficient.
The location should have adequate air circulation and keep out airborne
particles and moisture.
INSTALLING THE AIR LINE
Connect the air line to the air fitting on the compressor and to the back of
the gauge panel, then cut the air line and install it into the T fitting.
Run a length of air line from the newly installed T fitting, then attach the
air line to the air spring bag kit with another T fitting.
The dark part of the picture above is the installation steps of this part.
NOTE:
-
The air line can be cut with an air line cutter. The cut of the air line should be as smooth as possible.
-
The air line may be a little stiff. It is recommended to use a hair dryer to blow hot air on the air tube for 2 to 3 minutes before installing.
CONNECT THE WIRE HARNESS
A. Connect the wire harness (red) to the back of the gauge panel and to the compressor power lead, respectively.
The dark part of the picture above is the installation steps of this part.
NOTE:
You may need to cut the carpet to run the air line and red wire to the cab.
B. Install the ground wire (black) to the compressor mounting screw or frame rail.
The dark part of the picture above is the installation steps of this part.
C. Connect the fuse harness to the terminal of the switch and connect the
other end to the fuse box of the vehicle.
The dark part of the picture above is the installation steps of this part.
D. Choose the Fuse adaptor based on the type of fuse your vehicle uses.
OPERATING INSTRUCTION
A. Test the circuit and turn on the ignition to confirm that the
compressor is working properly. If the compressor is not running, use a test
light to make sure there is power on both sides of the switch.
B. Press and hold the switch to run the compressor, and release the
switch to stop the compressor once the desired height is reached.
C. Check all air line connections with soap solution to make sure there are no air leaks.
INSTALLATION COMPLETED
INSTALLATION COMPLETED
WARNING
Cancer and Reproductive Harm
www.P65Warnings.ca.gov
Since 2006
ABK-AAPDIPEI-VLC