Ivante S18 TWS Earphone User Manual
- August 3, 2024
- Ivante
Table of Contents
Ivante S18 TWS Earphone
Product Usage Instructions
- FCC and IC Compliance:
- Ensure compliance with FCC and IC regulations regarding license-exempt transmitter(s)/receiver(s) for the device to operate legally.
- Interference Conditions:
- Operate the device under the following conditions:
- The device must not cause interference.
- The device must accept any interference, even if it causes undesired operation.
- Operating in Canada:
- If using the device in Canada, adhere to the regulations set by Innovation, Science and Economic Development Canada for license-exempt devices.
FAQs
- Q: What should I do if the device causes interference?
- A: If the device is causing interference, try adjusting its placement or operating frequency. If the issue persists, contact customer support for further assistance.
- Q: How can I ensure my device complies with FCC and IC regulations?
- A: Make sure to read and understand the user manual thoroughly. Follow the guidelines provided for proper installation and operation of the device to maintain compliance.
What include
Connect
- Enable phone Bluetooth function.
- Take out the earbuds from the charging box, the white indication lights flash on the earbuds.
- Locate the device Bluetooth name “S18” on your phone to pair, the green lights will turn off when connected successfully. (The earbuds will auto-turn off if not connected to the device within 5 minutes.)
Touch Control
- X1: Tap once.
- X2: Tap twice.
- X3: Tap thrice.
- 2S: Press and hold for 2 seconds.
- 3S: Press and hold for 3 seconds.
- 6S: Press and hold for 6 seconds.
Troubleshooting
- Connected while no sound: Try to tap the right earbud to increase the volume.
- One earbud can not be charged: Clean the charging contacts of the earbud and its charging box.
- The charging box can not be charged: Ensure the charging cable is normal and there is no alien or over dirt in the type-C port.
Reset Earbuds
If there are connection or functional issues, please reset the earbuds:
- Delete the Bluetooth name “S18” from the phone list and disable the mobile Bluetooth function.
- Put the earbuds into the charging box to charge to full.
- Tap earbuds 4 times then press and hold control area for 3 seconds. (The light flashes quickly and lights off, which means reset successfully.)
- Then pair the phone with the earbuds as per the above Connect Part.
Safety instructions
- Keep the earbuds away from children under 3 years to avoid swallowing by mistake.
- Never listen to music at high volumes in case it damages your listening.
- Keep the product away from extremely hot and cold environments. It will damage the battery and circuit.
- Only charge your device from 5V USB ports in your phones, laptops, or PCs.
- Please clean the charging contacts of the earbuds and charging case frequently to avoid charging failures.
FCC
FCC Information
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, under Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used by the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harm or interfere ence to radio or television
reception, which can be determined by turning the equipment out and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
IC Information
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference. including interference that may cause undesired operation of the device.