ELED LPV-150RF-12 RF Constant Voltage LED Driver Owner’s Manual

: August 2, 2024
: ELED

Table of Contents

ELED LPV-150RF-12 RF Constant Voltage LED Driver
Product Information
Product Usage Instructions
Frequently Asked Questions
Features
Applications
Mechanical Structures and Installations
Technical Parameters
Wiring Diagram
Light on/off fade time
Match Remote Control
Output Load VS Temperature
Static characteristic
Installation precautions
Dimming Curve
Failure analysis and troubleshooting
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ELED LPV-150RF-12 RF Constant Voltage LED Driver

Product Information

Product Specifications:

Model: LPV-150RF-12, LPV-150RF-24
Type: RF Constant Voltage LED Driver
Dimming Interface: RF wireless, AC Push-dim
Input Voltage: Universal AC 110-277VAC
Output: 1 channel constant voltage, Max. 150W
Active PFC Function: 0.95 Typ
Protection: IP20
Compliance: IEC/EN standards, EN55015, EN61000-3-2 Class C, etc.

Product Usage Instructions

Wiring Diagram:
Refer to the provided wiring diagram for proper installation.
Dimming Methods:
- Short Press: Turn on or off the light.
- Long Press (1-6s): Step-less dimming; every other long press changes the light level direction.
- Dimming Memory: Light returns to the previous dimming level after power failure.
Synchronization:
To synchronize multiple LED drivers connected to the same push switch, do a long press for more than 15s. Ensure not to exceed 25 LED drivers per push switch and keep wire length under 20 meters.
Light On/Off Fade Time:
To set the light on/off time, follow the provided instructions for the long press and short press of the match key.
Match Remote Control:
Choose between two match ways: Use Match Key or Use Power Restart. Follow the steps provided to match or delete remote controls accordingly.

Frequently Asked Questions

Q: How many remote controls can one RF LED driver accept?

A: One RF LED driver can accept up to 10 remote controls.

Q: What is the maximum total output power of the LED driver?

A: The LED driver has a maximum total output power of 150W.

Q: How to reset the light on/off time to factory default?

A: Long press the match key for 10s to restore factory default parameters.

Features

Dimming interface: RF Wireless, AC Push-dim
Match with RF 2.4G single color remote control, one RF LED driver accepts up to 10 remote controls
Universal AC input/110-277VAC
1 channel constant voltage output, Max. total output power 150W
Built-in active PFC function: 0.95 Typ, THD<10%
Light on/off fade time 3s selectable
No load/Standby power<0.5W
Load / Over-heat / Short circuit protection
Suitable for indoor LED lighting application
5 Year, 50,000hr warranty

Applications

Suitable for LED-related fixtures or appliances that use LED light bars and LED tape (like LED Decoration or Advertisement devices).
Office/Commercial/Domestic Lighting, Hotels, Retail and Display.
Use for retrofit upgrades & new luminaire designs.

Mechanical Structures and Installations

Technical Parameters

Model	LPV-150RF-12	LPV-150RF-24

Output

Input

Protection

| Over Load| Output hiccups occur when the load is 110% to 140%, and recovery occurs automatically when the fault condition is removed.

℃

Over Temperature| Current decrease when PCB temp>110, recovers automatically after fault condition is removed
Short Circuit| Shut down the output voltage, which recovers automatically after the fault condition is removed

Environment

Safety&EMC

Wiring Diagram

RF Connection
AC Push-Dim connection

The provided AC Push-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switches.

Short press: Turn on or off the light.
Long press (1-6s): Press and hold to step-less dimming, with every other long press, the light level goes to the opposite direction.
Dimming memory: Light returns to the previous dimming level when switched off and on again, even at power failure.
Synchronization:
- If more than one LED driver is connected to the same push switch, do a long press for more than 15s, then the system is synchronized and all lights in the group dim up to 100%.
- This means there is no need for any additional synchrony wire in larger installations.
- We recommend the number of LED drivers connected to a push switch does not exceed 25 pieces,
- The maximum length of the wires from the push to the LED driver should be no more than 20 meters.

Light on/off fade time

Long press match key 5s, then short press match key 3 times, the light on/off time will be set to 3s, and the indicator light blink 3 times.
Long press match key 10s, restore factory default parameter, the light on/off time also restore to 0.5s.

Match Remote Control

Match Remote Control (two match ways)
The end user can choose the suitable match/delete ways. Two options are offered for selection:

Use Match key

Match:
- Short press the match key, and immediately press the on/off key (single zone remote) or zone key (multiple zone remote) on the remote.
- The LED indicator fast flashes a few times means the match is successful.
Delete:
- Press and hold the match key for 5s to delete all matches,
- The LED indicator fast flashes a few times means the match was deleted.

Use Power Restart

Match:
- Switch off the power 5s, then switch on the power 2s, repeat.
- Immediately short press the on/off key (single zone remote) or zone key (multiple zone remote) 3 times on the remote.
- The light blinks 3 times means the match is successful.
Delete:
- Switch off the power 5s, then switch on the power 2s, and repeat.
- Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times on the remote.
- The light blinks 5 times means all matched remotes were deleted.

When using multiple RF drivers, two application methods:

Auto-transmitting:
One driver can transmit the signals from the remote to another driver within 30m, as long as there is a driver within 30m, the remote control distance can be extended.
Auto-synchronization:
- Multiple drivers within a 30m distance can work synchronously when they are controlled by the same remote.
- Driver placement may offer up to 30m communication distance. Metals and other metal materials will reduce the range.
- Strong signal sources such as WiFi routers and microwave ovens will affect the range.
- We recommend for indoor applications that driver placements should be no further apart than 15 m.

Output Load VS Temperature

Static characteristic

Installation precautions

This product must be installed and adjusted by a qualified professional.
This product is non-waterproof. When installed outdoors, please ensure it is mounted in a waterproof enclosure.
The ambient temperature in which the product is installed must not exceed the value of Ta at any time.
LED drivers should keep a certain distance from the heating stuff(such as the luminaries radiator). The installation interval between the product and the product is recommended to be 20cm, so as not to affect the service life due to poor heat dissipation.
The installation height shall be ≥ 1m from the floor to avoid shortening the remote control distance due to too weak a reception signal.
The products are not allowed to be close to or covered by metal objects, with an interval of ≥ 20cm to avoid signal attenuation and shorten the remote control distance.
Avoid installation at the corner of the wall or the corner of the beam, with an interval of ≥ 20cm to avoid signal interference.

Dimming Curve

Failure analysis and troubleshooting

Fault

| Cause|

Solution

---|---|---
The light can not be turned on| 1. No power

2. Wrong wiring

| 1. Check the power supply

2. Connection test

The brightness of the light is inconsistent| 1. Output cable is too long

2. The wire diameter is too small

| 1. Reduce wire length or loop power supply

2. Replace Replace to thicker wires

Hiccup flashing light| Overload| Check the power of the LED light

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual >>