NIGHT OWL FBWNIP4U Wire Free Spotlight Camera User Guide

NIGHT OWL FBWNIP4U Wire Free Spotlight Camera

Product Information

Specifications

• Camera Type: Wire-free Spotlight Camera
• Resolution: 2K
• Connectivity: Micro USB
• Features: LED Lens, PIR Sensor, Microphone, microSD Card Slot

Product Usage Instructions

Initial Setup

1. Remove the protective lid to access the micro USB port.
2. Connect the micro USB cable to the camera and the USB power adapter.
3. Plug the USB power adapter into an outlet.
4. Wait for the camera to enter Pairing Mode.

Downloading the App

If you are a new user, download the Night Owl app from your app store. Create an account or log in if you already have one.

Adding the Camera

1. Open the Night Owl app.
2. Tap on “Add New” or “+”.
3. Scan the QR code on the camera.
4. Follow the on-screen instructions to add the camera.

Connecting to Wi-Fi

Make sure your Wi-Fi router’s security protocol is set to WPA/WPA2. Follow the app instructions for connecting your camera to the network.

Camera Installation

1. Use the holes on the back of the camera to mark screw positions on the mounting surface.
2. Insert screw anchors and secure the camera in place using the provided screws.

Frequently Asked Questions (FAQ)

• Q: What should I do if my camera is not entering Pairing Mode?
  A: Make sure the camera is fully charged by keeping it plugged in for up to 3 hours. If the issue persists, contact customer support.

• Q: Can I use a different USB power adapter?
  A: Yes, you can use any USB power adapter as long as it provides the required power output for the camera.

What’s Included

Wire Free Camera

NOTE : If mounting the camera, you will need a screwdriver or drill (not included).

Items Not Included

• Screwdriver
• Drill
• Drill Bit (15/64) (3/64)
• Router / Modem
• USB Power Adapter
• Mobile Device (Phone/Tablet)
• microSD Ca

Camera Details

Download the Night Owl App

• If you are a first-time user, go ahead and download the Night Owl app. Quickly create an account and log in.
• Already have an account? Simply log in.

Initial Start-up Steps

• Carefully lift off the rubber piece at the bottom of your camera to gain access to the micro USB charging port. Plug in the small end of the micro USB cable into the camera.

• Connect one end of the USB cable to a USB power adapter and plug it into an outlet. If you do not have a USB power adapter, you may use a USB charging port.

• After a few seconds of your camera being plugged in you will hear “Camera is in Pairing Mode”. You can now begin the installation process using the Night Owl application
  NOTE : Keep your camera plugged in for up to 3 hours to fully charge.

Add Your Camera

To begin viewing your camera, add it to the Night Owl app or to a compatible recorder.
For more detailed setup steps, scan the QR code below.

Connecting to a Wi-Fi router

Adding your camera.

1. Open Night Owl Protect app
2. Tap on “Add New” or “+”
3. Scan the QR code at the side of the camera
4. Follow the on-screen display to add the camera step by step.
   NOTE: The Router’s security protocol MUST be set to WPA/WPA2 (strong security).

If setup is completed using Network Discovery or Manual setup by UID once your device is added to the network you will need to select the category of the device to proceed.

Camera Installation

1. Use the holes in the back of each camera as a template to mark the screw positions on the surface where you plan to mount the camera.
2. Insert the screw anchors. Line up the camera base holes with the screw anchors, insert the screws through the base and tighten to secure the camera in place.

Need Help?

For more help, please follow the steps below to access your Series support page:

1. Please visit: Support.NightOwlSP.com
2. Enter FBWNIP4U into the Search bar or scan the QR Code

FCC RADIATION NORM FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Compliance Statement These limits are designed to provide reasonable protection against frequency interference in residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed or used in accordance
with the instructions, may cause harmful interference to radio communication.
However, there is no guarantee that interference will not occur in television reception, which can be determined by turning the equipment off and on. The user is encouraged to try and correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CAUTION!
The Federal Communications Commission warns the user that changes or modifications to the unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment should be installed and operated with a minimum distance of 8 inches between the radiator and your body.

QSG-FBWNIP4U 3-240717

References

• NightOwl SP

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>