KLIMATECHAIKI 801013369 Kitchen Hood Installation Guide
- July 26, 2024
- KLIMATECHAIKI
Table of Contents
KLIMATECHAIKI 801013369 Kitchen Hood
Product Information
Specifications
- Product Name: Hood for Kitchen
- Model: XYZ-123
- Power Supply: 220-240V, 50/60Hz
- Power Consumption: 150W
- Material: Stainless Steel
- Dimensions: 80cm x 60cm x 40cm
Product Usage Instructions
UseThe hood is designed to be used either for exhausting or filter versions.
Extraction Version
In this case, the fumes are conveyed outside of the building by means of a
special pipe connected with the connection ring located on top of the hood.
CAUTION! The exhausting pipe is not supplied and must be purchased
separately. The diameter of the exhausting pipe must be equal to that of the
connection ring.
Filtration Version
The aspirated air will be degreased and deodorized before being fed back into
the room. To use the hood in this version, install asystem of additional
filtering based on activated charcoal.
Installation
The minimum distance between the supporting surface for the cooking equipment
on the hob and the lowest part of the range hood must be not less than 50cm
from electric cookers and 65cm from gas or mixed cookers. Follow the gas hob
installation instructions if specifying a greater distance.
Instruction on mounting and use
Closely follow the instructions set out in this manual. All responsibility,
for any eventual inconveniences, damages or fires caused by not complying with
the instructions in this manual, is declined. This appliance is intended to be
used in household and similar application such as: – staff kitchen areas in
shop, offices and other working environments; – farm houses; – by clients in
hotels, motels and other residential-type environments; – bed and breakfast-
type environments.
The hood can look different to that illustrated in the drawings in this
booklet. The instructions for use, maintenance and installation, however,
remain the same.
- It is important to conserve this booklet for consultation at any moment. In the case of sale, cession or move, make sure it is together with the product.
- Read the instructions carefully: there is important information about installation, use and safety.
- Do not carry out electrical or mechanical variations on the product or on the discharge conduits.
- Before proceeding with the installation of the appliance verify that there are no damaged all components. Otherwise contact your dealer and do not proceed with the installation.
Note: The parts marked with the symbol “(*)” are optional accessories supplied only with some models or otherwise not supplied, but available for purchase.
Caution
- Before any cleaning or maintenance operation, disconnect hood from the mains by removing the plug or disconnecting the mains electrical supply.
- Always wear work gloves for all installation and maintenance operations.
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
- Children shall not be allowed to tamper with the controls or play with the appliance.
- Cleaning and user maintenance shall not be made by children without supervision.
- The premises where the appliance is installed must be sufficiently ventilated, when the kitchen hood is used together with other gas combustion devices or other fuels.
- The hood must be regularly cleaned on both the inside and outside (AT LEAST ONCE A MONTH).
- This must be completed in accordance with the maintenance instructions provided. Failure to follow the instructions provided regarding the cleaning of the hood and filters will lead to the risk of fires.
- Do not flambé under the range hood.
- For lamp replacement use only lamp type indicated in the Maintenance/Replacing lamps section of this manual.
- The use of exposed flames is detrimental to the filters and may cause a fire risk, and must therefore be avoided in all circumstances.
- Any frying must be done with care in order to make sure that the oil does not overheat and ignite.
CAUTION : Accessible parts of the hood may become hot when used with cooking appliances.
- Do not connect the appliance to the mains until the installation is fully complete.
- With regards to the technical and safety measures to be adopted for fume discharging it is important to closely follow the regulations provided by the local authorities.
- The air must not be discharged into a flue that is used for exhausting fumes from appliance burning gas or other fuels.
- Do not use or leave the hood without the lamp correctly mounted due to the possible risk of electric shocks.
- Never use the hood without effectively mounted grids.
- The hood must NEVER be used as a support surface unless specifically indicated.
- Use only the fixing screws supplied with the product for installation or, if not supplied, purchase the correct screws type.
- Use the correct length for the screws which are identified in the Installation Guide.
- In case of doubt, consult an authorized service assistance center or similar qualified person.
WARNING
- Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.
- Do not use with a programmer, timer, separate remote control system or any other device that switches on automatically.
- This appliance is marked according to the European directive 2012/19/EC on Waste Electrical and Electronic Equipment (WEEE).
- By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of the product.
- The symbol n the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal.
- For further detailed information regarding the process, collection and recycling of this product, please contact the appropriate department of your local authorities or the local department for household waste or the shop where you purchased this product.
Appliance designed, tested and manufactured according to:
- Safety: EN/IEC 60335-1; EN/IEC 60335-2-31, EN/IEC 62233.
- Performance: EN/IEC 61591; ISO 5167-1; ISO 5167-3; ISO 5168; EN/IEC 60704-1; EN/IEC 60704-2-13; EN/IEC 60704-3; ISO 3741; EN 50564; IEC 62301.
- EMC: EN 55014-1; CISPR 14-1; EN 55014-2; CISPR 14-2; EN/IEC 61000-3-2; EN/IEC 61000-3-3. Suggestions for correct use in order to reduce the environmental impact: Switch ON the hood at minimum speed when you start cooking and kept it running for few minutes after cooking is finished. Increase the speed only in
- case of large amount of smoke and vapor and use boost speed(s) only in extreme situations. Replace the charcoal filter(s) when necessary to maintain a good odor reduction efficiency. Clean the grease filter(s) when necessary to maintain a good grease filter efficiency. Use the maximum diameter of the ducting system indicated in this manual to optimize efficiency and minimize noise.
Use
The hood is designed to be used either for exhausting or filter version.
Extraction version
In this case the fumes are conveyed outside of the building by means of a
special pipe connected with the connection ring located on top of the hood.
CAUTION!
The exhausting pipe is not supplied and must be purchased apart.
The diameter of the exhausting pipe must be equal to that of the connection
ring.
CAUTION!
- If the hood is supplied with active charcoal filter, then it must be removed.
- Connect the hood and discharge holes on the walls with a diameter equivalent to the air outlet (connection flange).
- Using the tubes and discharge holes on walls with smaller dimensions will cause a diminution of the suction performance and a drastic increase in noise.
Any responsibility in the matter is therefore declined.
- Use a duct of the minimum indispensable length.
- Use a duct with as few elbows as possible (maximum elbow angle: 90°). ! Avoid drastic changes in the duct cross-section.
Filtration version
- The aspirated air will be degreased and deodorised before being fed back into the room.
- In order to use the hood in this version, you have to install a system of additional filtering based on activated charcoal.
- The models with no suction motor only operate in ducting mode, and must be connected to an external suction device (not supplied).
- The connecting instructions are supplied with the peripheral suction unit.
Installation
The minimum distance between the supporting surface for the cooking equipment
on the hob and the lowest part of the range hood must be not less than 50cm
from electric cookers and 65cm from gas or mixed cookers.
If the instructions for installation for the gas hob specify a greater
distance, this must be adhered to.
Electrical connection
The mains power supply must correspond to the rating indicated on the plate situated inside the hood. If provided with a plug connect the hood to a socket in compliance with current regulations and positioned in an accessible area, after installation. If it not fitted with a plug (direct mains connection) or if the plug is not located in an accessible area, after installation, apply a double pole switch in accordance with standards which assures the complete disconnection of the mains under conditions relating to over-current category III, in accordance with installation instructions.
WARNING!
Before re-connecting the hood circuit to the mains supply and checking the
efficient function, always check that the mains cable is correctly assembled.
The hood is provided with a special power cable ; if the cable is damaged,
request a new one from Technical Service.
Mounting
This type of cooker hood must be fixed to the ceiling.
Very heavy product; hood handling and installation must be carried out by at
least two persons.
Before beginning installation
- Check that the product purchased is of a suitable size for the chosen installation area.
- Remove the charcoal (*) filter/s if supplied (see also relative paragraph). This/these is/are to be mounted only if you want lo use the hood in the filtering version.
- Check (for transport reasons) that there is no other supplied material inside the hood (e.g. packets with screws (), guarantees (), etc.), eventually removing them and keeping them.
- Expansion wall plugs are provided to secure the hood to most types of walls/ceilings. However, a qualified technician must verify suitability of the materials in accordance with the type of wall/ceiling. The wall/ceiling must be strong enough to take the weight of the hood.
- Do not tile, grout or silicone this appliance to the wall. Surface mounting only.
Operation
- = ON/OFF – Speed increase
- = Lights ON/OFF
- = Selection of the desired function
- = Setting the function in use
- = The display shows:
- a – list of available functions
- b – indicator of the function currently in use c – indicator of the speed in use
- d – clock / data related to the function in use e – saturation of the anti-grease filter
- f – saturation of the carbon anti-odor filter
Available functions
SPEED
Switch on/Speed increase
- press button 1 to switch on the hood
- press button 1 to go to the next speeds, until the hood is switched off
The extraction speed is shown on the display (c), in the following manner:
*** The percentage displayed refers to the indicative value of the performance
The high speed is timed for 10 minutes; to interrupt the timing and switch off
the hood press button 1.
NB= the speed might increase automatically during use, this is because the
control is fitted with a system that protects the display in case of over
temperatures.
CLOCK
To set the clock
- press button 3 until moving the indicator(b) on the function
CLOCK”
- press button 4 to access clock setting
- keep button 4 pressed:
- keeping it pressed for one second increases the time by one minute
- after 10 seconds, each second it is pressed increases the time by 10 minutes
To store the set time
- press button 3
TIMER
Stopwatch Function
- press button 3 until moving the indicator(b) on the “TIMER” function
- press button 4 to access timer setting
- to start the stopwatch: simultaneously press button 3 and button 4, for 5 seconds
- to stop the stopwatch: simultaneously press button 3 and button 4, for 5 seconds
- Note= After 60 minutes the stopwatch stops automatically
“Countdown” Function
- press button 3 until moving the indicator(b) on the “TIMER” function
- press button 4 to access timer setting
To set the “Countdown” timer:
- keep button 4 pressed:
- keeping it pressed for one second increases the timer by one minute
- after 10 seconds, each second it is pressed increases the timer by 5 minutes
- To save the “Countdown” timer- press button 3
- The Timer indicator(b) will start flashing to indicate the start of the “Countdown”
- When the “Countdown” reaches “0:00” the motor is switched off
- Note = to set a new timer, button 4 must be pressed until the indication “0:00” is displayed again
- Note = the maximum countdown setting time is 60 minutes
GREASE FILTER
Display percentage of utilization:
- Press button 3 until moving the indicator(b) on the “GREASE
FILTER” function
- press button 4 to display the percentage of utilization of the grease filter
Grease filter reset warning
The grease filter warning is displayed after 40 hours of utilization with the
wording “RESET”(e) next to the “GREASE
FILTER” function
When this warning is displayed the grease filter must be washed.
After performing maintenance
- press button 3 until moving the indicator(b) on the “GREASE FILTER” function
- press button 4, for 5 seconds, to disable the warning and restart the grease filter efficiency percentage counting.
ODOUR FILTER
Display percentage of utilization: – press button 3 until moving the
indicator(b) on the “ODOUR FILTER” function
- press button 4 to display the percentage of utilization of the carbon anti-odor filter
Carbon anti-odor filter reset warning
The carbon anti-odour filter warning is displayed after 160 hours of
utilization with the wording “RESET”(f) next to the “ODOUR FILTER” function
When this warning is displayed the carbon anti-odor filter must be washed or
replaced (depending on the model you have)
After performing maintenance:
- press button 3 until moving the indicator(b) on the “ODOUR FILTER” function
- press button 4, for 5 seconds, to disable the warning and restart the carbon anti-odor filter efficiency percentage counting.
NB= The anti-odor carbon filter function is disabled by default -to enable the anti-odor carbon filter signal, please follow these steps: with the cooker hood turned off, simultaneously press buttons 3 and 4 for 5 seconds; the words “ODOUR FILTER” will appear on the display, indicating that the signal is on. Repeat the same procedure to disable it.
Maintenance
Cleaning
Clean using ONLY the cloth dampened with neutral liquid detergent. DO NOT
CLEAN WITH TOOLS OR INSTRUMENTS. Do not use abrasive products. DO NOT USE
ALCOHOL!
Grease filter-Fig. 23-26
- Traps cooking grease particles.
- This must be cleaned once a month (or when the filter saturation indication system – if envisaged on the model in possession – indicates this necessity) using nonaggressive detergents, either by hand or in the dishwasher, which must be set to a low temperature and a short cycle.
- When washed in a dishwasher, the grease filter may discolor slightly, but this does not affect its filtering capacity.
- To remove the grease filter, pull the spring release handle.
Charcoal filter (filter version only)-Fig. 25
It absorbs unpleasant odors caused by cooking.
The activated charcoal filter can be one of these types:
- Washable activated charcoal filter.
- NON-washable activated charcoal filter.
Washable activated charcoal filter
- The charcoal filter can be washed once every two months using hot water and a suitable detergent, or in a dishwasher at 65°C (if the dishwasher is used, select the full cycle function and leave dishes out).
- Eliminate excess water without damaging the filter, then remove the mattress located inside the plastic frame and put it in the oven for 10 minutes at 100° C to dry completely. Replace the mattress every 3 years and when the cloth is damaged.
NON-washable activated charcoal filter
- The saturation of the charcoal filter occurs after more or less prolonged use, depending on the type of cooking and the regularity of cleaning of the grease filter.
- In any case it is necessary to replace the cartridge at least every four months.
- The charcoal filter may NOT be washed or regenerated.
Assembly
- Hook the charcoal filter at the back on the metal tongue of the hood first, then on the front with the two knobs. Disassembly
- Remove the charcoal filter by turning the knobs and fixing it to the hood by 90°.
Replacing lamps
- The hood is equipped with a lighting system based on LED technology.
- The LEDs guarantee optimum lighting, a duration up to 10 times as long as the traditional lamps and allow to save 90% electrical energy.
- For replacement, contact the technical service.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>