FitSpark WL-101 Wireless Microphone User Manual

: July 25, 2024
: FitSpark

Table of Contents

FitSpark WL-101 Wireless Microphone
Product Usage Instructions
PRODUCT OVERVIEW
FCC Radiation Exposure Statement
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FitSpark WL-101 Wireless Microphone

Specifications:

Model: WL-101
Microphone: Omni directional radio, DSP intelligent noise reduction
Size: 105*80mm

Product Usage Instructions

Power On/Off:

To power on or off the microphone, long press the power button for 2 seconds. The power indicator light will illuminate when the device is powered on.

Volume Control:

Increase Volume:

Short press once to increase the volume by 1 grid (total of 4 grids). A prompt sound will indicate maximum volume.
Long press to enter mute mode; long press again to exit mute mode.

Decrease Volume:

Short press once to decrease the volume by 1 grid (total of 4 grids). A prompt sound will indicate minimum volume.
Long press to enter noise reduction mode; long press again to exit noise reduction mode.

Charging:

The charging indicator light will flash with a low battery prompt sound when the battery is low. While charging, the indicator light will be on; it turns off when fully charged.

Connection Status:

The connected status light flashes during pairing and remains on steadily when successfully connected to the receiver.

Earphone Monitoring:

For real-time audio monitoring, plug in 3.5mm jack earphones (not included) into the earphone monitoring hole.

FAQ

Q: How do I know if the microphone is fully charged?
- A: The indicator light will turn off once the microphone is fully charged.
Q: Can I use any earphones for audio monitoring?
- A: Yes, you can use any 3.5mm jack earphones for real-time audio monitoring.

PRODUCT OVERVIEW

Fixed clip :

The wireless microphone is fixed within 20cm of the emitting area, such as the collar of a garment.

Microphone:

Omni directional radio, DSP intelligent noise reduction.

Power button:

Long press power button 2 seconds to power on or off, and the power indicator light will be light up when powered on.

Increase volume+:

Short press once to increase the volume 1 grid, there is 4 grid volumes in total. When the volume reaches its maximum, there will be a prompt sound.
Long press to enter the mute mode, and long press again to exit the mute mode.

Decrease volume-:

Short press once to decrease the volume 1 grid, there is 4 grid volume 1n total. When the volume reaches its minimum, there will be a prompt sound.
Long press to enter the noise reduction mode and long press again to exit the noise reduction mode.

Charging indicator:

When it is low battery, the indicator light flashes with a low battery prompt sound.

The indicator light is light up when charging, once fully charged, the indicator light will light off.

Connected status light:

The pairing search status light flashes when turned on, and the light remains on for a long time when successfully connected to the receiver.

Earphone monitoring hole :

Plug in 3.5mm jack earphones (not included) to monitor audio recording effects in real time.

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

CONTACT US

Specifications are subject to change without prior notice. Please refer to the actual specifications!
For any inquiries, questions, or comments about our products, please send an email to SUPPORT@MYFITSPARK.COM.

We will reply as soon as possible.

Customer Care Email : support@myfitspark.com
Website: https://www.myfitspark.com