BRINKS 7257 LED Large Area Dusk to Dawn Security Light Instruction Manual

BRINKS 7257 LED Large Area Dusk to Dawn Security Light Instruction Manual

INSTALLATION INSTRUCTIONS

Congratulations on your purchase of a Brink’s LED Yard Light Fixture. You have purchased a safe, dependable, easy-to-install security lighting system. You can use this xture at home for outdoor lighting applications.

WHAT’S INCLUDED:

A Metal Pole Clamp

B Fixture Housing

C Wire Connectors (3)

D Mounting Screws (2)

E Clamp Screw

F Clamp Nut

G Canopy Mounting Plate

H 40W LED

J Plastic Lens

RISK OF FIRE. MAINTAIN AT LEAST 2 INCH SPACING BETWEEN FIXTURE HOUSING AND THE MOUNTING SURFACE.

IMPORTANT SAFETY INFORMATION

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH ALL APPLICABLE INSTALLATION CODES.

• IF YOU ARE NOT FAMILIAR WITH ELECTRICAL WIRING, IT IS RECOMMENDED THAT YOU SECURE THE SERVICES OF A WELL QUALIFIED ELECTRICIAN WHO CAN ASSURE THAT THIS INSTALLATION MEETS LOCAL, STATE, AND NATIONAL CODES. THIS PRODUCT MUST BE

INSTALLED BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

• BE SURE POWER IS TURNED OFF AT THE MAIN POWER PANEL OR FUSE BOX PRIOR TO INSTALLATION OR REPLACING FIXTURE.
• Before installing this FIxture, be sure to check with local ordinances regarding approved outdoor lighting. This FIxture style may not be allowed in some areas.
• This FIxture is for outdoor use only.
• This FIxture is for wall mount or pole mount installation only.
• The electrical system and the method of connecting the FIxture to the system must be in accordance with local, state, and national electric codes.
• This FIxture is to be connected to a 120 volt, 60 Hz power source. Connecting to a different power source may create a hazard and will void the warranty.
• This FIxture is suitable for wet locations.
• Do not use near or around FIammable/combustible material or liquids.
• Risk of electric shock. Do not attempt to open the FIxture housing or lamp. There are no serviceable parts inside.
• Fixture must not be installed facing reFIective surfaces closer than FIve (5) feet.
• Carefully read through the entire installation instructions before installing this security light FIxture.

NOTE

• This FIxture is equipped with a photo cell which automatically turns off the light during the day light. To check if FIxture is operable during daylight hours, or to bypass photo sensor as your desire, simply cover the photo sensor with duct tape or black electric tape.
• For pole installation, recommended pipe size is within Ø1-5/8” overall.
• Not intended for use with emergency exit Fixture’s of lights, electronic timers, motion detectors, or dimmer switches.

INSTALLATION INSTRUCTIONS LOCATION

• Select a location on a structurally sound, at wall or pole 10-25 feet above the ground.
• Fixture should be located on wall or pole at least 18 inches below any overhang or other structural detail.
• Fixture should not be recessed and must be positioned with bulb in vertical position and bulb socket base up.
• 120v/60Hz power must be available at the desired location. If not, have a qualified electrician route power to that location.
  

JUNCTION BOX MOUNTING

1. Tum OFF power at the switch or circuit breaker prior to the installation process or when replacing the lamp.

2. Feed wires from junction box through center of Canopy Mounting Plate (G), then connect as follows:
   a. Connect black fixture wire to black supply wire using
   Wire Connector (C).
   b. Connect white fixture wire to white supply wire using
   Wire Connector (C).
   c. If applicable, connect copper fixture ground wire to the ground wire using
   Wire Connector (C) or to junction box grounding screw in accordance with electric codes.

3. Secure Canopy Plate (G) to junction box using two (2) Mounting Screws (D). Tighten with screwdriver and adjustable wrench.

4. Slide Metal Pole Clamp (A) through the center of the integral post.

5. Push Fixture Housing (B) onto Canopy Plate (G) and secure with Metal Pole Clamp (A), Clamp Screw (E), and Clamp Nut (F).

6. Attach Plastic Lens (J) by lining up slots in lens to tabs on Fixture Housing (B), then twist to secure into place.

7. Install Lamp (H) into lamp socket. Do not over-tighten.

8. Apply weatherproof silicone caulk or sealant around the fixture base and to unused screw holes.

9. Tum power back ON.
   

POLE MOUNT INSTALLATION

STEP BY STEP INSTRUCTION FOR POLE MOUNT INSTALLATION:

1. Turn OFF power at the switch or circuit breaker prior to the installation process or when replacing the lamp.

2. Slide Metal Pole Clamp (A) through the center of the integral post.

3. Feed wires from pole and connect as follows:
   a. Connect black fixture wire to black supply wire from junction box using
   Wire Connector (C).
   b. Connect white fixture wire to white supply wire from junction box using Wire Connector (C).
   c. If applicable, connect copper fixture ground wire to the ground wire using
   Wire Connector (C) in accordance with electric codes.

4. Push Fixture Housing (B) onto pole (not included) and secure with Metal Pole Clamp (A), Clamp Screw (E), and Clamp Nut (F).

5. Attach Plastic Lens (J) by lining up slots in lens to tabs on Fixture Housing (B), then twist to secure into place.

6. Install Lamp (H) into lamp socket. Do not over-tighten.

7. Apply weatherproof silicone caulk or sealant around integral post and metal pole surface.

8. Tum power back ON.
   
   

TROUBLESHOOTING

If this fixture fails to operate properly, check to make sure:

• The correct lamp is properly installed
• The fixture is wired correctly
• The lamp is not faulty
• The fixture is grounded correctly
• The line voltage at the fixture is correct

LIMITED LIFETIME WARRANTY – This product is warranted to be free from defects in material and workmanship for life of product. If a defect occurs, call 1-800-562-5625 for instructions on how to have defective product repaired or replaced free of charge. LIMITATIONS – This warranty only covers Brink’s assembled lighting products and accessories and is not extended to other components, Lamp Bulb(s), or equipment used on the product.
Warranty extends to original purchaser of product. Receipt or other approved proof of purchase required for warranty service. NOT LIABLE FOR INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or  exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. NOT COVERED – Product failure not relating to faulty material or workmanship, corrosion of brass components, reimbursement for installation or unauthorized service.

50 Icon, Foothill Ranch, CA 92610-3000 USA
email:info@hamptonproducts.com
www.hamptonproducts.com • 1-800-562-5625 Made in China

Questions: For further assistance or more information, please call 1-800-562-5625,8 am – 5 pm (Pacific Time),Monday – Friday.

Brink’s trademark & copyright work are used with permission.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>