Newland FM530 IVD Scanners User Guide
- July 15, 2024
- Newland
Table of Contents
Newland FM530 IVD Scanners
- Type: Red Laser
- Wavelength: 515nm
- Pulse Width: 200us
- Classification: Class 1
- Output: Less than 1.0 mW
Wire Color Functions
- Red: Power Supply
- Orange: Switch Input
- Purple: Ground
- Black: Switch Output
- White: RS-232 Input
- Green: RS-232 Output
- Yellow: Shield
Signal Descriptions
- DC IN: Power supply
- SW IN: Switch input
- GND: Ground
- SW OUT: Switch output
- RS 232 RXD: RS-232 input
- RS 232 TXD: RS-232 output
- FE/Shield: Shield
Additional Information
Reserved for future use. Visit our website at newland-id.com for updates and support.
Frequently Asked Questions (FAQ)
Q: What should I do if the red LED is on?
A: If the red LED is on, it indicates a device malfunction. Please contact
customer support for assistance.
Laser safety warning
Warning!
Please note the following safety guidelines
- The FM530 is a laser class 1 device. Do not stare into the beam.
- Turn off the laser aimer upon completion of scanner positioning/ aiming. Aiming is not needed in operation.
Appearance
Dimensions
(unit: mm)
installation
Note: Note: Use the laser aimer in debug mode to ensure the reading area is centered on the codes to be read.
Note:
- When the scanner is initially powered, the laser aimer is disabled by default.
- The laser aimer is intended to be used during installation via debugging mode to optimize installation and then disabled in normal use.
- For more details on using the laser aimer, refer to the Key Operation section and the user guide.
Scanning range
Interface pinouts
Functions
LED Indicators
| Item | Description |
|---|---|
| Status | Green LED on: the device is powered on and enters the standby state. |
Red LED on: it indicates device malfunction. Orange LED on: the device enters the debugging mode.
Read| Green LED flashes, and it indicates a good read.
Link| Not provided currently’ with ‘Reserved for future use
USB debugging interface
The Type-C interface is used to upgrade the device and update and download the
firmware.
Key operations
Enter Debug Mode
- While pressing the key button, apply power to the scanner. Continue to press the key button until the aiming laser turns on and the scanner emits three beeps, then release the key button.
- While in debug mode, the laser aimer will come on, indicating the center of the scan area.
- While in the debug mode, the scanner will prefix the number of good reads as a prefix to the barcode data, allowing optimization of the scanner position and aiming.
- To exit debug mode, either depress the key button until the scanner emits three beeps, then release the key button, or cycle power to the scanner. While in working mode, press the key button once and the scanner will emit a single beep and go into single read mode, turning on illumination until a code is read or the key button is pressed again.
- While in working mode, holding the key button down until the scanner beeps three times will enable continuous mode. Holding the button down again until the scanner beeps three times and exits the continuous mode.
Marking and European Economic Area (EEA)
Statement of Compliance
We hereby declare that this device is compliant with the mandatory
requirements and provisions under Directive 2014/53/EU, EN 62471:2008 IEC
60825-1:2014, EN 60825-1:2014+A11:2021, EN 50689:2021
Recycling
This product bears the selective sorting symbol for waste electrical and
electronic equipment (WEEE), meeting EU directive 2012/19/EU
Programming barcodes
FCC
- Radiofrequency interface requirements Radio transmitters (part 15)
- This device complies with part 15 of FCC standards, concerning RF compatibility and susceptibility
Tested to comply with FCC Standards
- FOR HOME OR OFFICE USE
Maintenance and repair
Caution!
- Protect the scan window from abrasion and contamination.
- If the scan window needs to be cleaned, use a clean, lint-free cloth and commercially available window cleaner.
- There are no user-serviceable parts within this product.
- Upon encountering faults, please refer to Newland technical support and service for repair and advice.
More information
Visit our website newland-id.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>