AMPED OUTDOORS AO4S-130 Lithium Iron Phosphate Battery Owner’s Manual

: July 13, 2024
: AMPED OUTDOORS

Table of Contents

AO4S-130 Lithium Iron Phosphate Battery
Product Information
Product Usage Instructions
Features
Applications
General Specifications
User Guide
Frequently Asked Questions
Troubleshooting
Warnings
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AO4S-130 Lithium Iron Phosphate Battery

Product Information

Specifications

Model: AO4S-130 Dual Purpose
Battery Type: Lithium Iron Phosphate Battery LiFePO4
Nominal Voltage: 12.8V
Rated Capacity: 130Ah
Features: Group 31, Bluetooth, IP67 Waterproof, Heated

Product Usage Instructions

Charging the Battery
To charge the battery, follow these steps:

Ensure the charging voltage is set to 14.0~14.4V.
Connect the recommended charge current, which can go up to 100A but is encouraged to be kept below 65A.
Monitor the charging process and disconnect once fully charged.

Discharging the Battery
When discharging the battery:

Avoid discharging too low or causing short circuits.
Maintain uniform voltage during discharge for optimal performance.
Do not exceed the maximum continuous discharge current of 165A.

Environmental Considerations
Ensure the battery operates within the recommended temperature range:

Charge Temperature: @25°C (77°F)
Discharge Temperature: @25°C (77°F)
Storage Temperature: Follow IP Rating Guidelines

Maintenance and Storage
Store the battery in a cool, dry place when not in use. Periodically check the battery status and ensure it is properly maintained to prolong its lifespan.

Features

Wider temperature range: -20°C~75°C. (Lower temperatures will result in decreased capacity)
Lighter Weight: About 40%~ 50% less weight of comparable lead acid battery.
Usable Capacity: Delivers twice the power of lead-acid batteries.
Quality BMS: BMS (Battery Management System) will protect your battery from overcharging, discharging too low, or short circuits with built-in cell balancing. Now with advanced Bluetooth monitoring!
Extraordinary cycle life: Offers 2000+ life cycles, up to 5x longer than lead acid batteries, helping to minimize replacement cost and reduces total cost of ownership.
Series and Parallel Configurations: Up to four batteries in series and eight batteries in parallel.
Voltage: Uniform voltage during discharge.

Applications

Trolling Motors
Fishing Electronics
Solar & Wind power systems
Backup Power
Lighting
Much More!

General Specifications

| Performance Specifications| General Parameters|

Comments

---|---|---|---

Electrical Characteristics

| Nominal Voltage| 12.8V|

Nominal Capacity

|

130Ah

| Standard charge after

Standard discharge

at 80%DOD

Short Circuit Protection| 1780A|

Charge Specifications

| Charging Voltage| 14.6V|
Recommended Charge Voltage| 14.0~14.4V|

Recommended Charge Current

|

Up to 100A. We encourage below .5c (65A or lower)

Max.Charge Current| ≤145A| @25℃ (77℉)
Charge Cut-off Voltage| 14.6V| Resting voltage 13.8V

Discharge Specifications

| Standard Discharge| ≤50A| @25℃ (77℉)
Max. Continuous Discharge Current| ≤165A| @25℃ (77℉)
Max.Pulse Current| 800A(<5s)| @25℃ (77℉)
Discharge Cut-off Voltage| 10.0V| Resting voltage 12.0V

Environmental

| Charge Temperature| Heated to 149℉|

@65±20% Relative Humidity

Discharge Temperature| -20 to 75℃(-4 to 167℉)
Storage Temperature| -20 to 45℃(-4 to 113℉)
IP Rating| IP67 Case Rating|

Mechanical

|

LengthWidthHeight

| 12.9×8.66×6.77″

327220171mm

|

Height without terminals

User Guide

Charging: Using the Amped Outdoors charger, connect the battery to the charger (you will see the charger light turn green)and then plug in the AC cable into the wall outlet. The charging light will turn red when charging and when the charge is complete, the light will turn green again. If you are using our 10A charger, a fan will also kick in while charging. When the charge is complete, remove the battery from the charger as a float charger is not needed with our batteries. If you are not using an Amped Outdoors charger, please refer to the troubleshooting section if your battery will not take charge.
Other Chargers: Using an onboard charger, we highly encourage you to use one made for 12.8V LiFePO4 batteries only. Most aftermarket chargers will not reset a BMS (battery management system) when triggered. How to reset a BMS is explained in the troubleshooting section later in this guide. We DO NOT recommend the use of a Power Pole or other 36v onboard charging systems on this battery, for proper balancing, each 12v battery needs its charging source when wiring in series.
Connecting your battery: With your source being turned off, connect your battery to your source. Ensure that you have a tight, solid connection and use the provided hardware such as lock washers and washers if you have a battery with bolts. It is highly encouraged to use dielectric grease on all connections to prevent any corrosion from water exposure. Check your connections regularly along with cables, connectors, or other components to make sure they are free of corrosion and wear and all connections remain tight.
Housing and mounting: Please ensure your battery is mounted or in the proper box before use. Depending on your application, it is important to keep your battery from moving around or being exposed to elements. Our batteries do not require venting so a sealed case or enclosure will only help protect the battery. Although our batteries have a superior waterproof rating, it is encouraged to keep your products free from elements to prevent the buildup of water, corrosion, and debris. This will ensure your battery will look and perform like new for the expected life of the product.
Long-term battery storage: Never store your battery fully discharged. It is best to put a 50% to full charge on your battery and then remove it from the charger. To ensure the best performance from your batteries for many years, put a short charge or use your battery at least once every 2-3 months. The best temperature to store a lithium battery is between 40-80 degrees F. A cool and dry place is ideal. The maximum discharge rate of our batteries would not exceed 2% per month in storage. Do not place a lithium battery on a charger for extended periods when not in use. Lithium batteries will last longer if not stored at a 100% charge rate for a long period.

Frequently Asked Questions

Can I connect multiple batteries in series or parallel?

A- Yes, you can connect up to four batteries in series and eight batteries in parallel for increased capacity or voltage requirements.

What is the cycle life of the battery?

A- The battery offers over 2000 life cycles, which is up to 5 times longer than lead-acid batteries, providing cost savings in the long run.

Does the battery have Bluetooth monitoring?

A- Yes, the battery features advanced Bluetooth monitoring capabilities to track performance and status remotely.

Do I need a special charger?

A- We HIGHLY encourage the use of the appropriate charger with our batteries to ensure a full charge, speed of charge, and proper cell balancing, it is wise to use our chargers. Chargers that are Lithium, often do not include the feature to reset a battery BMS. This means they will not charge a battery that has been fully drained and may read below 10V.

How do I store my battery?

A- Never store your battery fully discharged. It is best to put a 50% to full charge on your battery and then remove it from the charger. To ensure the best performance from your batteries for many years, put a short charge or use your battery at least once every 2-3 months.

Can I lay my battery on its side?

A- Yes, all of our batteries can be mounted in any orientation as long as you secure them appropriately. Ensure that all terminal posts are free from all metal to prevent a short circuit. We do recommend upright as the battery is intended for stability.

Do I need to discharge my battery before recharging?

A- No, it is advised that you charge your battery before each use. Lithium batteries will not have a memory and even though it is safe to drain the battery 100%, it is advised to drain lower depth of discharge.

For Additional FAQ: https://ampedoutdoors.com/pages/faq.

Troubleshooting

The battery will not hold or accept a charge:
- Lithium Batteries have a built-in BMS (Battery Management system) that will trigger when a battery is depleted or it is triggered into protection. The voltage of the battery may read less than 4v. Our chargers will reset a BMS to begin charging but many on-board or aftermarket chargers may not do this because they think the battery is bad. You can connect another charged 12V battery in parallel (red to red and black to black) like jump-starting a vehicle. This will reset the BMS and allow you to charge again.
- If you have our charger, check the voltage output of the charger. The charger will output 14.4-14.6V and will reset the BMS. If it does not, then you likely have a blown fuse on the charger or the charger is not working. Ensure all connections are tight and your AC outlet is working.
Battery just stops: This is typical of a battery BMS (Battery Management System) being triggered. One of the following has happened: Depleted Capacity, Short Circuit, Over Current, Excessive Heat. You can reset the BMS by connecting another battery in parallel or connecting to the proper charger. The BMS is built in to protect the battery and your components.

Contact for additional troubleshooting: Service@ampedoutdoors.com.

Warnings

Lithium batteries are very safe as long as they are used correctly. Please contact us if you have any questions on your applications.

Do not crush, puncture, or attempt to dismantle the battery.
Do not place the battery near an open flame and try to avoid direct heat.
Do not dispose of the battery in the trash. Please find a local lithium recycler.
Do not place the battery in fluids such as salt water, acid, or alkaline.
Do not short-circuit the battery terminals.
Do only use the approved chargers.
Never store the battery in a fully depleted state of charge.

Warning:
Cancer and Reproductive Harm WWW.P65WARNINGS.CA.GOV.