IKEA IDASEN Adjustable Table Frame Instructions

July 12, 2024
Ikea

IKEA IDASEN Adjustable Table Frame

Product Information

Specifications:

  • Sound level: Lower than 55 dB(A)
  • Height setting interval: 60-124 cm / 23.6-48.8 inch
  • Maximum load: 75kg / 165lbs
  • Power supply unit: DC 24V, 140W
  • Model: ASW0551-24020002A

Product Usage Instructions

Installation Instructions:

  1. Assemble the table according to the separate assembly instructions.
  2. Connect the cable from one leg to the other. Connect the hand control and the power supply to the leg. Ensure that the cables are placed in the tray created by the frame to prevent damage.
  3. Connect the electrical cable to a wall socket. Ensure the cable has full mobility.
  4. The table is now ready for use. The motors will stop automatically when the table reaches its lowest and highest position.

Usage of the Table:

  • The table should only be used as a working table with the ability to adjust working height between sitting and standing positions.
  • Use the table indoors in dry premises such as an office environment.
  • Do not overload the table; maximum load capacity is 75 kg / 165 lbs.
  • The system can be run continuously for a maximum of 2 minutes. Afterward, the motors must stand by for approximately 18 minutes before further use.

FAQs

How do I connect additional Bluetooth devices to the table?
To add additional Bluetooth devices (up to 8 devices):

  1. Go to your mobile device’s Bluetooth menu.
  2. Connect to DESKxxxxx.

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical furnishing, basic precautions should always be followed, including the following:
Read all instructions before using the product.

  • DANGER
    To reduce the risk of electric shock: Always unplug this furnishing from the electrical outlet before cleaning.

  • WARNING
    To reduce the risk of burns, fire, electric shock, or injury to persons:

  1. Unplug from outlet before putting on or taking off parts.
  2. Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.
  3. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
  4. Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the furnishing to a service center for examination and repair.
  5. Keep the cord away from heated surfaces.
  6. Do not use outdoors.
  7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
  8. The table must not be overloaded –maximum load is 75kg/165lbs
  9. Only use intended IKEA table tops.

Specification

  • Sound level: Lower than 55 dB(A).
  • Height setting interval: 60-124 cm/23.6-48.8 inch
  • Maximum load: 75kg/165lbs.
  • Temperature interval at usage: +10 °C up to + 40 °C/+50 up to +104 °F.
  • Temperature interval at storage: -18°C up to 70°C/0 up to 158°F.
  • Humidity: 20% up to 90% at 40°C/104°F.
  • Power supply unit: DC 24V, 140W.
  • Model: ASW0551-24020002A

This appliance shall only be used together with the included power supply unit.
Every person who is responsible for this table at installation or employment of the table in daily use or in service and repair work should carefully read these instructions. Keep these instructions close to your sit/stand table.

Installation instructions

  • The table is assembled according to separate assembly instructions.

  • Connect the cable from one leg to the other. Connect the hand control and the power supply to the leg.

  • The cables to legs, hand control and power supply should be placed in the tray created by the frame. Place the electrical cables so that they do not get damaged, see assembly instruction.

  • Connect the electrical cable to a wall socket.
    NOTE! The electrical cable must have full mobility.

  • The table is now ready for use. The motors stop automatically when the table reaches its lowest and highest position respectively.

Usage of the table

The table shall only be used as a working table with the possibility to continuously adjust working height between sitting and standing position. The table shall only be used indoors and in dry premises (office environment or similar).

The table must not be overloaded – maximum load is 75 kg/165 lbs. The system may be run continuously for a maximum 2 minutes. Afterward, the motors must stand by for approx. 18 minutes before they can be used again.

QUICK GUIDE

  • If you have an IOS device:
    Go to the App Store and download the Desk Control app. The app will take you through the process of installing your Desk control.

  • If you have an Android device:
    Go to Google Play and download the Desk Control app. The app will take you through the process of installing your Desk control.

Add additional Bluetooth device(s) (max 8 devices)

  1. Go to your Bluetooth menu on your mobile device and connect to DESKxxxxx.
  2. Once Bluetooth connection is established, the blue LED stops blinking.

Up to 8 devices can be stored by the system. When the 9th device is paired the system will remove the device that have not been connected for longest time

Factory reset:
Press manoeuvre button for 10 sec. This deletes all paired Bluetooth devices. Follow these instructions when adjusting table height:

  1. Make sure no objects are in the way of the table adjusting height freely.
  2. In order to run the table up/down, press the manoeuvre button up and down respectively or use your Desk control app.

Safety regulations

  • When the table is run up/down, keep the necessary safety distance to avoid the risk of getting squeezed between the moving tabletop and fixed objects in the surrounding area.
  • When the table is run up/down the user shall keep watch so that nobody is injured or no object is damaged. The table top must not bump into a fixed object so that the table is overturned. Always remove any office chair before the table is run up/down.
  • The table tripod must not be altered or reconstructed in any way. In service and repair work of the table, the electrical cable must always be disconnected from the wall socket.
  • Modifications to the legs are absolutely forbidden!
  • The table must not be used as a hoisting device for persons.

Maintenance and repair instructions

  • After approx. 1 week of use, check that the screws are properly tightened.
  • If the table cannot be lowered or raised, check the connections between the legs and the wall socket and be sure your phone/Bluetooth device is turned on and connected through the Desk Control app.
  • If any part of the electrical system is replaced, the electrical cable must first be disconnected from the wall socket. Replace the electrical part and then connect the electrical cable to the wall socket. The table is now ready for use.

If the table still does not work, please contact your nearest IKEA store or customer service.

PRODUCT SERVICING
Do not attempt to repair this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks.
Manufacturer: IKEA of Sweden AB
Address: Box 702, SE-343 81 ÄLMHULT

FCC STATEMENT

This device complies with Part 15 of the FCC Rules/Industry Canada license- exempt RSS standard(s). Operation is subject to the following two conditions:

  1. this device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation of the device.

WARNING: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by IKEA is under license. Other trademarks and trade names are those of their respective owners.

The crossed-out wheeled bin symbol indicates that the item should be disposed of separately from household waste. The item should be handed in for recycling by local environmental regulations for waste disposal. By separating a marked item from household waste, you will help reduce the volume of waste sent to incinerators or landfills and minimize any potential negative impact on human health and the environment. For more information, please contact your IKEA store.

Troubleshooting guide

NOTE! Do always disconnect the cable from the wall socket before maintenance!

Symptom Check Try
The desk does not run Is the main connected to the leg? Try to connect a

lamp or similar to the main supply to check that the supply voltage is OK.
Are all plugs mounted correctly between the legs and power supply? See assembly instruction.| Check all connections.
Are there visual damages on the cables, controls or the legs?| Damaged parts must be exchanged – Contact IKEA Customer Service.
The desk stops and can only run in the opposite direction.| Is the desk in fully extracted position?| When the desk has reached its upper position it can only run downwards.
Is there much load on the desk compared to when the desk functioned normally?| Remove some of the load and try again.
The desk will only run downwards even though the desk is not overloaded.|  | Perform Basic settings.
The desk does not run with full stroke length upwards. Always stops at the same position.|  | The system has a new endstop outwards. Perform Basic settings to remove this stop.
The desk does only run a little upwards and stops.| Has the correct screws been used when mounting the frame to the legs?| Check if the screw used have the correct length (assembly instruction). If the screw is too long it can damage the leg.
Is all connections correct?| Check all connections.
Is the desk loaded much?| Reduce weight load and try again. A Basic setting might be needed before the desk will drive upwards.
Basic Setting: Push the controller downwards. Run the table to the bottom position and keep the pressure on the controller for min. 6 seconds after both legs have reached bottom position. At certain errors types this must be done twice in succession. Now the desk is in initial position.

Technical data

Model Name IDÅSEN Motorised desk/table
Type number D1801
Input 120V~60Hz 1.2A
Standby Power Consumption <0.1 W
Operating temperatures 10°C to 40°C/+50 to +104 °F
Operating humidity 20 to 90%RH at 40°C/+104 °F
Sound level: <55 dB(A)
Height setting interval: 60-124 cm/23.6-48.8 inch
Maximum load: 75kg/165lbs

Bluetooth Version| V 4.2
Wireless range in open-air| 8-10 m/26’ – 32’
Operating frequency| 2.4 – 2.48 GHz
Radio output power| +4dBm

© Inter IKEA Systems B.V. 2024

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals