LG LTE, WCDMA, GSM Wireless Module Instruction Manual

LG LTE, WCDMA, GSM Wireless Module

Important Information

This document has been submitted under terms of Non-Disclosure Agreement. By accepting deliver of this document, the recipient acknowledges and agrees that: i) the recipient will use this document only for the purpose for which it has been supplied; ii) the recipient will not disclose this information to anyone not covered by our mutual NDA; and iii) all the information contained herein will be treated as strictly confidential material.

Revision History

Executive Summary

Device Introduction

Cellular modem_LW-9880G is a telecommunication (PLS63-W) modem module that supports LTE / WCDMA / GSM with up to 10.2Mbps download, and 5.2Mbps upload.

Electrical Specifications

General Specifications

UART serial interface
Common Air interface| FDD-LTE / TDD-LTE / WCDMA / GSM
Frequency band (LTE & WCDMA & GSM)| B2, 4, 5, 12, 13, 26, 66 / II, IV, V / 850, 1900
DC input operating voltage| Typical Input 5V, DC Converter output 3.8V
Maximum current @ +5VDC, Maximum TX Power (23dBm)| Under 1 A
Dimensions| 33.0 x 29.0 x 2.5mm
Operating temperature(board temperature)| Normal operation: -30°C to +75°C
Extended operation: -40°C to +85°C

Table 2-1 General Specifications

HW Specifications

WCDMA

| Standard| 3GPP Release 7|
UE Category| WCDMA|
WCDMA Support| Band 2, 4, 5|
Duplex Mode| HD-FDD|
RF Paths| 2 x Rx / 1 x Tx|
Reference Sensitivity| 3GPP Spec all eet|
Maximum Tx Power| 24dBm +1.7/-3.7dBm| @Antenna Port
UMTSTransmit Data Rate| PS data rate – 384 kbps DL / 384 kbps UL CS data rate – 64 kbps DL / 64 kbps UL|
HSDPA

Transmit Data Rate

| DL 7.2Mbps, UL 5.7Mbps|
ITEM| SPECIFICATION
---|---
GSM| Standard| GSM / GPRS / EDGE|
GSM Support| 850, 1900|
Duplex Mode| Time Domain|
RF Paths| 1 x Rx / 1 x Tx|
Max power| 850 : +33dBm ±2 dBm
1900 : +30dBm ±2 dBm| @Antenna Port

Table 2-2 HW Specifications

Environmental Specifications

Automatic shutdown2

Temperature measured on PLS63 Board

| Non-condensing| <-40| >+95| °C

Mechanical Specifications

Table 3-1 Mechanical Specifications

Mechanical Appearance

Mechanical Dimensions

Cellular modem_LW-9880G Interface

Application Note of Cellular modem_LW-9880G Interface

Power Supply

The input power of Cellular modem_LW-9880G is Typical DC+5.0V. (+5% / -5%)

UART Signal

Data communication between HOST and Cellular modem_LW-9880G is through TTL Level (3.3V). The signals and specifications are as stated below.

• M : Module H : HOST * Signal name is based on module
  Table 4-1 UART Interface description

USB Interface

Cellular modem_LW-9880G supports USB 2.0 High speed via 5 Pin Connector

Table 4-2 USB Interface description

4 E-SIM Interface

Cellular modem_LW-9880G supports E-SIM interface via 8 Pin.

Table 4-3 E-SIM Interface Description

Antenna Approved Source

Description

This is the product specification of Internal Antenna applied to Set

Electrical Properties

Specification

Impedance`

Nominal Impedance

– R = 50Ω

Measuring Method

By using Network analyzer , connect the antenna-installed handset to the reflection Point of Analyzer and measure the impedance value within the designated frequency band.

Directive ness Omni-directional

Gain( Free Space)

Radiation Pattern (XY-Plane)

Compliance with FCC Rules and Regulations

FCC Identifier: BEJ-LW9880G

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Regulatory notice to host manufacturer according to KDB 996369 D03 OEM Manual List of applicable FCC rules

• FCC Part 22, 24, 27, 90 of the FCC rules.
  Summarize the specific operational use conditions

• The OEM integrator should use equivalent antennas which is the same type and equal or less gain then an antenna listed below this instruction manual.
  Limited module procedures

• The module is a single module.
  Trace antenna designs

• The module with trace antenna designs, and the Antenna Specification document includes the layout of trace design and measurement data.

RF exposure considerations

• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
• This equipment should be installed and operated with a minimum distance of 20 cm (7.8 inches) between the antenna and your body. Users must follow the specific operating instructions for satisfying RF exposure compliance.

Mobile use

• As long as the conditions above are met, further transmitter testing will not be required.
• OEM integrators should provide the minimum separation distance to end users in their end-product manuals.

Antennas:

• This module is certified with the following integrated antenna.
• Max. Antenna gain: 3.08 dBi / Ant. Type: Carrier press Type
  Any new antenna type, higher gain than listed antenna should be met the requirements of FCC rule 15.203 and 2.1043 as permissive change procedure.

Label and compliance information

• The module is labeled with its own FCC ID. If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following:

“Contains FCC ID: BEJ-LW9880G”

Information on test modes and additional testing requirements

• OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, additional transmitter in the host, etc.). Additional testing, Part 15 Subpart B disclaimer
• The final host product also requires Part 15 subpart B compliance testing with the modular transmitter installed to be properly authorized for operation as a Part 15 digital device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>