W T RS485 Screw Cord Instructions

July 10, 2024
W T

W T RS485 Screw Cord Instructions

Legal information

As we can make mistakes, none of our statements may be used without verificati- on. Please notify us of any errors or misunderstandings you become aware of so that we can recognise and correct them as quickly as possible.

Warning concept

These instructions contain information that must be observed for your personal safety and to prevent damage to property. The instructions are emphasised by a warning triangle. Depending on the hazard level, the warnings are shown in descending order as follows:

Danger

Indicates a hazard that will result in death or serious injury if appropriate precautions are not taken.

WARNING

Indicates a hazard that could result in death or serious injury if appropriate precautions are not taken.

__ CAUTION

Indicates a hazard that could result in minor injury if appropriate precautions are not taken.

ATTENTION

Indicates  a  hazard  that  can  result in  property damage if  appropriate precautions  are not  taken. If there are several hazard levels, the warning of the highest level is always used. If a warning notice with a warning triangle warns of personal injury, a warning of property damage may also be included in the same warning notice.

Qualified personnel

The product described in these instructions may only be installed and commissioned by personnel who are qualified for the respective task. The relevant documentation for the respective task must be observed, in particular the safety instructions and warnings contained therein. Qualified personnel are able to recognise risks and avoid potential hazards when handling the described products due to their training and experience.

Disposal

Electronic devices must not be disposed of with household waste, but must be disposed of properly as electronic waste.

Symbols on the product

Saftey instrucions

General instructions

These instructions are intended for the installer of the RS485 Schraubschnurzel de- scribed in the manual and must be read and understood before starting work. The devices may only be installed and commissioned by qualified personnel.

Intended user

__ DANGER

The  RS485  Schraubschnurzel  sold  by  Wiesemann  &  Theis  is  an adapter that is used to extend the RS485 interface on W&T devices. Any other use or modification of the adapter is not intended.

Electrical safety

__ DANGER

Before  starting  any  work  with  the  Schraubschnurzel,  the  pow- er supply  must  be  completely  disconnected  using  suitable  measu- res. Ensure that the device cannot be switched on again accidentally! The Schraubschnurzel  may  only  be  used  in  closed  and  dry  rooms. The adapter should not be exposed to high ambient temperatures or di- rect sunlight and should not be operated in the vicinity of heat sources. Plea- se note the restrictions with regard to the maximum ambient temperature. A distance of 10-15 cm should be maintained between the adapter and neighbou- ring heat sources.
Ensure that no individual wires are protruding from strands, that the complete strand is in the terminal and that the screws of the connection terminals are tight. Tighten the screws of unused terminals.

ATTENTION

The complete declarations of conformity for the devices described in the instructions can be found on the respective Internet data sheet page on the W &T homepage at http://www.wut.de.

Product description

RS485 Schraubschnurzel with 1x RS485 (DB9) & A-/B+/GND

RS485 DB9 socket to 3-pole screw contact for tapping, forwarding or distributing an RS485 signal

Pinout

Compatibility

The RS485 Schraubschnurzel is compatible with the following RS485 capable W&T devices

Overview

Devices Article number
Serial PC cards #13631, #13610, #13611, #13601
Modules #18611, #18613, #18813
Interfaces #86201, #86203, #64201, #38211,

#61201, #81215, #61210, #65210

COM-Server| #58665, #58662, #58661, #58651,

#58652, #58034, #58669

**** DIL switch settings

To extend the RS485 2-wire signal, the DIL switches on the W&T interface must be set correctly. For details, see the instructions for your device.

Termination

All RS485 operating modes require the bus system to be terminated with a termi- nation network, which ensures a defined idle state in the high- impedance phases of bus operation. The bus system can be connected to a termination network in the in- terfaces by closing DIL switches 6 and 7 on the RS422/RS485 module. A maximum of 2 terminations per segment are permitted.

Connection example

Mounting

The RS485 Schraubschnurzel is intended for mounting on a W&T RS485-capable interface. The adapter has two screws for mechanical fixing.

Product dimension

Technical data

Connections

Connection             1x DB9 RS485 2-wire socket
1x 3-pole screw contact (A-/B+/signal-ground)
Other data
Housing:                                 Plastic
Protection class:                    IP20 Storage temperature:  -25°C .. 70°C Operating temperature:  0°C .. 70°C
Permissible humidity:            5..95% Relative humidity (non-condensing)

Wiesemann & Theis GmbH Porschestraße 12
42279 Wuppertal / Germany

Mail           info@wut.de
Web           www.wut.de
Tel.            +49 (0)202 2680-110
Fax             +49 (0)202 2680-265

Read More About This Manual & Download PDF:

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals