ALATECH WT001 Weight Training Bluetooth Sensor User Manual
- June 3, 2024
- ALATECH
Table of Contents
WEIGHT TRAINING
BLUETOOTH SENSOR WT001
User Manual
FEATURES
Wireless Connection
Bluetooth Low Energy technology connectivity via app.
Quick installation
Once fixed on the training equipment, the sensor will start to record reps in
sets.
Accurate Measurement
With an app that quantifies and analyzes your hard work, you can have a grasp
of your progress.
APP (Android / iOS)
Scan to download AlaFitness.
System Requirements:
- iOS 11.0 or later
- Android 5.0 or later
- Bluetooth 4.0
https://www.alatech.com/Download/action-download.htm
IN THE BOX
PLACE BATTERY
- Twist the battery cover counter-clockwise to OPEN and remove the cover.
- Place the battery (CR2032) into the cover with positive (+) side facing the inside of the battery cover. Make sure the sealing ring is in the groove of the battery cover.
- To reinstall the battery cover, align the cover dot with OPEN.
- Press and twist the cover clockwise back into place (the cover dot points to LOCK).
- Check if the battery back cover is securely locked to ensure water resistance.
INSTALLATION
First Fasten Sensor into Base
- Face the side with logo upward and slide the sensor into the base.
- Be sure to fit in the hole and the bump on the sensor and base.
Install on Barbell
- Place the sensor and the base on the barbell, logo facing upward.
- Use the Rubber O-ring to tie the sensor on the barbell. The Rubber O-ring should be attached to the hooks on both sides of the sensor.
- Make sure the sensor is fixed and will not hinder your movement.
Install on Weight Plate
- Place the sensor (with base) on top of the weight plate, logo facing upward.
- Lift the weight plate/weight stack for a couple of times to confirm the sensor is fixed and immovable, and will not hinder your movement.
TROUBLE SHOOTING
How to connect the sensor via Bluetooth within App?
– Please install AlaFitness on your mobile device.
– Turned on Bluetooth® on your mobile device.
– Open the app. Follow the on-screen instructions to register on App and set
up User’s Profile.
– Swipe left and select [Weight Training] > Connect: [wtSensor]. On the
displayed device list, select [WT001].
– Select [NEXT STEP] > [Start], and follow the on-screen instructions to
complete the operation.
Why can’t I connect the sensor in App?
– Please use AlaFitness on your mobile device.
– Make sure the Bluetooth® on your mobile device has been turned on.
– In order to save battery power, the sensor will enter sleep mode after 5
minutes of no action or Bluetooth connection. Please shake it slightly to
wake it up. Please repeat this step if it has been left idle for another 5
minutes.
– Keep the transmission distance between the sensor and your mobile device
within 2 meters.
– Check the battery. If exhausted, please replace the battery.
SPECIFICATIONS
- Name: Weight Training Bluetooth Sensor WT001
- Dimension: L37.4×W35.5×D16.85 mm (Base included)
- Weight: 14.7g (CR2032 + Base included)
- Waterproof: IPX7
- Operating temperature: -10~60°C (14~140°F)
- Wireless transmission interface: Bluetooth 4.0
- Wireless transmission frequency: 2.402~2.480 GHz
- Battery: CR2032
- Battery life: approx.300 Hours
Note: The flashing green light in every 5 seconds indicates Bluetooth
connection; red light indicates no connection.
FCC
Federal Communications Commission Statement
This device complies with FCC Rules Part 15. Operation is subject to the
following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a class
B digital device, pursuant to Part 15 of the Federal Communications Commission
(FCC) rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment causes harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by doing one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user‘s authority to operate the equipment.
The antenna(s) used for this transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. To maintain compliance
with FCC exposure compliance requirement, please follow operation instruction
as documented in this manual.
PRODUCT WARRANTY
We thank you for purchasing. We provide a one-year manufacturer’s warranty
from the date of purchase.
Warranty period:
We provide repair service free of charge but such service will be limited to
normal use only. Any damage caused by misuse of users shall not be covered by
the warranty hereof.
- We offer a risk free 90 day warranty on all replacement parts that we offer for you.
- User will pay for postage of replacement products from home to our service center.
(Please pack properly)
Non-Warranty Repair Policy: (User needs to pay for the repairs.)
- If malfunction or damage is caused by improper use, disassembly and modification.
- If damage is caused by accident, abuse, misuse, flood, fire, earthquake, any other natural disasters or human negligence.
- Due to normal wear and tear of consumptive parts such as battery, battery cover, base, rubber O-ring, etc.
- If any serial number has been removed or defaced.
- If it is damaged after the warranty expires.
Model
Date of purchase
YYYY / MM / DD
Serial No.*
SN:
Dealer’s Stamp
Customer Service
ALATECH TECHNOLOGY LIMITED
39F., No.758, Jungming S. Rd.
Taichung City 40255
TEL:+886-4-2260 8341#14
9:30-17:30, PST, M-F
(Only applies to the Taiwan Area.)
Manufacturer
Zhejiang ALA Fitness Technology LTD.
No.405 Tongxin Road, Tongxiang Economic
Development Zone, Zhejiang, China
- The serial number is printed directly on the back of device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>